• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.3
• /
• pp.300-310
• /
• 1999

A constant-volume combustion chamber is developed to measure the burnt gas temperature over the wide ranges of equivalence ratio from 1.5 to 2.7 and pressure from 0.1 to 2.7 and pressure from 0.1 to 6 MPa by two-color method. The combustion temperature is also calculated by the conventional two-region model. The premixed fuel rich propane-oxygen-inert gas mixtures under high pressures are simultaneously ignited by eight spark plugs located on the circumference of combustion chamber with 45 degree intervals. The eight converging flames compress the end gases to high pressures. The transmissiv-ity in the chamber center during the final stage of combustion at the highest pressure is measured by in situ laser extinction method. Comparisons are made with the combustion temperatures between two-color method and two-region model. It is found that the burnt gas temperature mea-sured by two-color method is higher than that calculated by two-region model because of being the negative temperature gradient on the calculation and the temperature distribution of light path-length on the measurement and the burnt gas temperature for the turbulent combustion is higher than that of the laminar combustion under the same conditions because the heat loss for turbulent combustion is lower due to the shorter combustion period.

• International Journal of Aeronautical and Space Sciences
• /
• v.12 no.4
• /
• pp.379-384
• /
• 2011

This paper performs numerical prediction of fuel temperature in the fuel tanks of unmanned air vehicles for both ground static non-operating and in flight transient conditions. The calculation is carried out using a modified Dufort-Frankel scheme. For this calculation, it is assumed that a non-operating vehicle on the ground is subjected to repeating daily cycles of ambient temperature with solar radiation and wind under 1%, with a 20% probability of hot day conditions. The energy conservation equation is used as the governing equation to calculate heat transfer between the fuel tank surface and the ambient environment. Results of the present analysis may be used as the estimated initial values of fuel temperatures in a vehicle's fuel tank for the purpose of analyzing transient fuel temperatures during various flight missions. This research also demonstrates that the fuel temperature of the front tank is higher than that of the rear tank, and that the difference between the two temperatures increases in the later phases of flight due to the consumption of fuel.

• Journal of the Korean Dietetic Association
• /
• v.27 no.1
• /
• pp.45-58
• /
• 2021

This study evaluated the sanitation management standards for vegetable preparation processes without a cooking stage. The aerobic plate counts (APC), coliform counts, and Escherichia coli of the samples at each production step were analyzed, and microbial growth of the samples stored at different temperatures was measured. The validation was judged in accordance with the microbial criteria stipulated by the British PHLS. After washing and disinfection, the APCs of the two samples decreased to 3~4 log CFU/g in both seasons. Compared to the purchasing stage, the decrease in coliform counts was approximately 0~3 log CFU/g in both seasons; E. coli was not detected. The initial APC and coliform levels of two vegetable samples were 4~5 log CFU/g in both seasons, with an increase of 1 log CFU/g taking more than 6 h at 25℃ and 2 h at 35℃. More than 10 h at 25℃ and 6 h at 35℃ were required to increase the E. coli O157:H7 count by 1~2 log CFU/g for two seasoned samples. In conclusion, washing and disinfection effects and changes in microbial growth during room temperature storage were similar in the two vegetables. Despite the low sanitizing effect of the two vegetables, when cut vegetables were stored under the critical limit within 2 h at two different room temperatures, seasoned lettuce and chicory were at the 'satisfactory' or 'acceptable' levels of PHLS regardless of the storage temperatures. The validation of sanitation management standards applied to vegetable preparation with the no-cook step was approved.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.2
• /
• pp.517-522
• /
• 2013

Small size ice-cream maker has two evaporators having different evaporating temperatures of $4^{\circ}C$ and $-8^{\circ}C$. In such case, ice-cream maker system design becomes complicated because multiple capillary tubes affects one another. In this study, performance analysis was conducted for the soft ice-cream maker having two evaporators operating at different temperatures. The compressor was analyzed using efficiency models, the capillary tube was modeled assuming one-dimensional flow, the condenser and the evaporators were modeld based on UA-LMTD method. The refrigeration cycle simulation program was developed applying the enthalpy, pressure and mass balance on each component. Comparison of the test data with the simulated results for R404A revealed that evaporator temperatures of refrigerator and freezer agreed within $3^{\circ}C$.

• Fisheries and Aquatic Sciences
• /
• v.17 no.2
• /
• pp.229-247
• /
• 2014

Seven feeding trials were conducted to determine the effects of feeding rate and frequency in the Korean rockfish Sebastes schlegeli at seven different water temperatures. Two feeding-rate experiments for 5-g Korean rockfish at $17^{\circ}C$ and $20^{\circ}C$; three feeding rate experiments for 16-g Korean rockfish at $16^{\circ}C$ and $24^{\circ}C$; and finally, two feeding frequency experiments for 93- and 100-g at $15^{\circ}C$ and $20^{\circ}C$ were conducted. Twenty fish averaging $5.5{\pm}0.2$ g ($mean{\pm}SD$) were randomly distributed into 18 indoor tanks containing 40-L seawater from a semi-recirculation system. Fish were fed a commercial diet for 4 weeks at water temperatures of $17^{\circ}C$ and $20^{\circ}C$. Two feeding trials were conducted to determine the optimum feeding frequency in growing Korean rockfish reared at temperatures of $15^{\circ}C$ and $19^{\circ}C$. Broken line regression analysis of weight gain (WG) indicated that the optimum feeding rates of 5-g growing Korean rockfish were 4.48% (BW/day; BW, body weight) at $17^{\circ}C$ and 4.83% (BW/day) at $20^{\circ}C$. Broken line regression analysis of WG showed optimum feeding rates of 16-g juvenile Korean rockfish of 3.41% (BW/day) at $16^{\circ}C$, 3.75% (BW/day) at $20^{\circ}C$, and 3.34% (BW/day) at $24^{\circ}C$. The biological performance, results, along with morphological indices and serological characteristics, suggest that a feeding frequency of 1 meal/day was optimal to improve WG in growing Korean rockfish grown from 93 to 133 g at a water temperature of $15^{\circ}C$, and 100 to 132 g at $19^{\circ}C$.

• The Journal of Korean Obstetrics and Gynecology
• /
• v.23 no.2
• /
• pp.116-123
• /
• 2010

Purpose: During Postpartum period many women complain multiple pain, cold hypersensitivity, hot flush, sweating and so on. We call the postpartum disease as San Hu Pung. We studied DITI Characters of women suffering from Postpartum disease. Methods: We studied 74 postpartum women visiting OOhospital from February 2006 to December 2009. The subjects were categorized in two groups, symptom group and no symptom group. We measured the temperatures of abdomen, upper and lower limb and back. We studied the difference of DITI between two groups by Student T-test using SPSS for windows(version 17.0). Results: The general characteristics were not different statistically. Temperatures of abdomen and back of two groups were not different statistically. Temperatures of both LR3 of symptom group were statistically higher than no symptom group. The difference of both PC8 and LU4, both LR3 and ST32 of symptom group were statistically higher than no symptom group. Conclusion: The results suggest that women suffering from Postpartum disease shows high temperatures on hand and foot. It seems that postpartum disease patients tend to have blood deficiency. DITI can be useful to diagnose San Hu Pung. More studies to diagnose San Hu Pung would be needed.

• Fisheries and Aquatic Sciences
• /
• v.14 no.4
• /
• pp.323-332
• /
• 2011

To find seasonally optimal microalgae for mass culture of the rotifer Brachionus plicatilis, the growth rates of 12 microalgal species (two marine Chlorella spp., five marine Nannochloris spp., two marine Nannochloropsis spp., one estuarine Nannochloropsis sp., and two estuarine Chlorella spp.) were compared at $25^{\circ}C$ at 15 psu and 30 psu. Among these, six species showing high growth rates were chosen and examined again at high ($30^{\circ}C$ and $32^{\circ}C$) and low ($10^{\circ}C$) temperatures. Their amino and fatty acids and the dietary value of the rotifers that fed on each microalgal species were examined. Nannochloris sp. (KMMCC-119) and Chlorella vulgaris (KMMCC-120) showed the highest growth rates at temperatures over $30^{\circ}C$ and at $10^{\circ}C$, respectively. The growth rate of Nannochloris was higher than those of Chlorella and Nannochloropsis at high temperatures, but lower than those of the latter at low temperatures. The growth rate of rotifers fed on Nannochloropsis was highest and that of those fed on Chlorella was lowest. Levels of eicosapentaenoic acid and docosahexaenoic acid were highest in Nannochloropsis and lowest in Nannochloris. However, total amino acid content was highest in Nannochloris and lowest in Chlorella. In conclusion, Nannochloropsis sp. (KMMCC-33) was the best microalgal species for the mass culture of the rotifer. However, during high- or low-temperature seasons in which Nannochloropsis does not grow well, Nannochloris spp. (KMMCC-119, 395) and C. vulgaris (KMMCC-120) would adequately replace Nannochloropsis sp. (KMMCC-33).

• Economic and Environmental Geology
• /
• v.24 no.2
• /
• pp.151-165
• /
• 1991

The Au-Ag deposits of the Euiseong area occurred in quartz veins which filled fissures in Cretaceous sedimentary and volcanic rocks. These ore veins can be classified in two types of deposits based on metallic mineral assemblages as follow: a pyrite type gold-silver deposit (Hoedong mine), characterized by Cu sulfides with Au-Ag alloy, and a Sb-rich silver deposit (Keumdongdo mine), characterized by base metal with Ag-bearing sulfosalts. Mineralogic and fluid inclusion evidences suggest that the ore minerals of these deposits was deposited from initial high temperatures (near $350^{\circ}C$) to later lower temperatures ($200^{\circ}C$) with moderate salinity fluids ranging from 5.8 to 3.8 eq. wt. % NaCl. The gold-silver mineralization of the Hoedong mine occurred at temperatures between 300 and $200^{\circ}C$ from fluids with log $f_{s_2}$ of -10 ~ -16 atm. The antimony - silver mineralization of the Keumdongdo mine were deposited at the higher temperatures (350 to $250^{\circ}C$) and $f_{S_2}$ (-10 ~ -13 atm) than gold mineralization of the Hoedong mine. The calculated log f02 of fluids at $250^{\circ}C$ in two deposits are -32 to -34 atm and -36.5 to -38.5 atm, respectively. Boiling evidences indicate that the ore mineralization of the Hoedong mine occurred at more shallow depth (0.5km) than that (1km) of the Keumdongdo mine. The above differences of depositional environments between two deposits caused the compositional changes of ore minerals such as electrum and sphalerite.

• Journal of Korean Society for Atmospheric Environment
• /
• v.32 no.1
• /
• pp.46-56
• /
• 2016

In order to analyze the surface temperature in accordance with the surface material, surface temperatures between Thermal InfraRed Image (TIRI) and Landsat 8 satellite observed at the commercial area (Gwanghwamun) and residential area (Jungnang) are compared. The surface temperature from TIRI had applied atmospheric correction and compared with that from Landsat 8. The surface temperatures from Landsat 8 at Gwanghwamun and Jungnang are underestimated in comparison with that from TIRI. The difference of surface temperature between the two methods is greater in summer than in winter. When the analysis area was divided into detailed regions, depending on the material and the position of the surface, correlation of surface temperature between TIRI with Landsat 8 is as low as 0.29 (Gwanghwamun) and 0.18 (Jungnang), respectively. The results were caused from the resolution difference between the two methods. While the surface temperatures of each zone from Landsat 8 were observed almost constant, high-resolution TIRI observed relatively precise surface temperatures. When the each area was averaged as one space, correlation of surface temperature between TIRIs and Landsat 8 is more than 0.95. The spatially averaged surface temperature is higher at Jungnang, representing residential areas, than at Gwanghwamun, representing commercial areas. As a result, the observation of high resolution is required in order to observe the precise surface temperature. This is because it appears that the spatial distribution of the various surface temperature in the range of micro-scale according to the conditions of the ground surface.

• Advances in concrete construction
• /
• v.15 no.6
• /
• pp.359-376
• /
• 2023

Ultra-high-performance concrete (UHPC) has become an attractive cast-in-place repairing material for existing engineering structures. The present study aims to investigate age-dependent high-early-strength UHPC (HESUHPC) material properties (i.e., compressive strength, elastic modulus, flexural strength, and tensile strength) as well as interfacial shear properties of HESUHPC-normal strength concrete (NSC) composites cured at different season temperatures (i.e., summer, autumn, and winter). The typical temperatures were kept for at least seven days in different seasons from weather forecasting to guarantee an approximately consistent curing and testing condition (i.e., temperature and relative humidity) for specimens at different ages. The HESUHPC material properties are tested through standardized testing methods, and the interfacial bond performance is tested through a bi-surface shear testing method. The test results quantify the positive development of HESUHPC material properties at the early age, and the increasing amplitude decreases from summer to winter. Three-day mechanical properties in winter (with the lowest curing temperature) still gain more than 60% of the 28-day mechanical properties, and the impact of season temperatures becomes small at the later age. The HESUHPC shrinkage mainly occurs at the early age, and the final shrinkage value is not significant. The HESUHPC-NSC interface exhibits sound shear performance, the interface in most specimens does not fail, and most interfacial shear strengths are higher than the NSC-NSC composite. The HESUHPC-NSC composites at the shear failure do not exhibit a large relative slip and present a significant brittleness at the failure. The typical failures are characterized by thin-layer NSC debonding near the interface, and NSC pure shear failure. Two load-slip development patterns, and two types of main crack location are identified for the HESUHPC-NSC composites tested in different ages and seasons. In addition, shear capacity of the HESUHPC-NSC composite develops rapidly at the early age, and the increasing amplitude decreases as the season temperature decreases. This study will promote the HESUHPC application in practical engineering as a cast-in-place repairing material subjected to different natural environments.