• Geomechanics and Engineering
• /
• v.14 no.1
• /
• pp.61-69
• /
• 2018

The first part shows the optimal contact surface for T-shaped combined footings to obtain the most economical dimensioning on the soil (optimal area). This paper presents the second part of a new model for T-shaped combined footings, this part shows a the mathematical model for design of such foundations subject to axial load and moments in two directions to each column considering the soil real pressure acting on the contact surface of the footing with one or two property lines restricted, the pressure is presented in terms of an axial load, moment around the axis "X" and moment around the axis "Y" to each column, and the methodology is developed using the principle that the derived of the moment is the shear force. The classic model considers an axial load and a moment around the axis "X" (transverse axis) applied to each column, i.e., the resultant force from the applied loads is located on the axis "Y" (longitudinal axis), and its position must match with the geometric center of the footing, and when the axial load and moments in two directions are presented, the maximum pressure and uniform applied throughout the contact surface of the footing is considered the same. To illustrate the validity of the new model, a numerical example is presented to obtain the design for T-shaped combined footings subjected to an axial load and moments in two directions applied to each column. The mathematical approach suggested in this paper produces results that have a tangible accuracy for all problems.

• Korean Management Science Review
• /
• v.24 no.1
• /
• pp.91-111
• /
• 2007

In this paper an effective two-phase approach adopting modified p-median mathematical model is proposed for grouping machines and parts in cellular manufacturing(CM). Unlike the conventional methods allowing machines and parts to be improperly assigned to cells and families, the proposed approach seeks to find the proper block diagonal solution where all the machines and parts are properly assigned to their most associated cells and families in term of the actual machine processing and part moves. Phase 1 uses the modified p-median formulation adopting new inter-machine similarity coefficient based on the non-binary production data-based part-machine incidence matrix(PMIM) that reflects both the operation sequences and production volumes for the parts to find machine cells. Phase 2 apollos iterative reassignment procedure to minimize inter-cell part moves and maximize within-cell machine utilization by reassigning improperly assigned machines and parts to their most associated cells and families. Computational experience with the data sets available on literature shows the proposed approach yields good-quality proper block diagonal solution.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.17 no.2
• /
• pp.223-234
• /
• 2014

This paper proposes a flexible and highly reusable modeling methodology for a next-generation combat entity which enables joint analysis of performance/engagement effectiveness. According to the scope of the proposed work, the paper is divided into two parts; Part 1 focuses on a conceptual model design, whereas Part 2 proposes detailed model specification and implementation. In Part 1, we, first, classify the combat entity model as combat logic and battlefield function sub-models for joint analysis. Based on the sub-models, we propose two dimensional model partition method, which creates six groups of a single combat entity model by two dimensions: three-activity and two-abstraction. This grouping enables us to reconfigure the combat entity model by sharing the same interface within the group, and the same interface becomes the fundamental basis of the flexible model composition. Furthermore, the proposed method provides a model structure that effectively reflects the real world and maximizes the multi-level reusability of a combat entity model. As a case study, we construct a model design for anti-surface ship warfare. The case study proves enhancement of model reusability in the process of scenario expansion from pattern running to wire guided torpedo operations.

• Journal of Korean Institute of Industrial Engineers
• /
• v.22 no.1
• /
• pp.105-114
• /
• 1996

Telecommunication services are typically offered with two-part tariffs which consist of the access charges and the usage charges. In the previous analyses of optimal two-part tariffs, consumers have been assumed to be final users. In this paper, we take the telecommunication service as an input factor which is purchased by business consumers. We proposed a two-stage market model in which the good in queston is produced by an upstream monopolist and purchased as an input by firms and they sell their final outputs in a downstream market. We derive the optimal two-part tariffs of inputs in the case of oligopolistic downstream market with heterogeneous downstream firms. It is shown that two-part tariffs are more desirable than uniform prices from a welfare standpoint. It is also shown that if an upstream monopolist earns positive profits, usage charge is less than marginal cost in the optimal two-part tariffs.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.143-146
• /
• 1996

In this paper, we propose a hopfield model for solving the part-matching which is the number of parts and positions are changed. The goal of this paper is to minimize part-connection in pairs and net total path of part-connection. Therefore, this kind of problem is referred to as a combinatorial optimization problem. First of all, we review the theoretical basis for hopfield model to optimization and present two method of part-matching; Traveling Salesman Problem (TSP) and Weighted Matching Problem (WMP). Finally, we show demonstration through computer simulation and analyzes the stability and feasibility of the generated solutions for the proposed connection methods.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.51 no.2
• /
• pp.203-211
• /
• 2015

The purpose of this study is to identify the flow resistance of the bottom pair trawl nets. The bottom pair trawl nets being used in fishing vessel (100G/T, 550ps) was selected as a full-scale net, and 1/10, 1/25 and 1/50 of the model nets were made. Converted into the full-scale net by Tauti's modeling rule and Kim's modeling rule, when resistance coefficient k of each net was calculated by substituting into above equation for flow resistance R and wall area of nets S values of each net ${\upsilon}$. Because resistant coefficient k decreases exponentially according as flow velocity ${\upsilon}$ increases to make $k=c{\upsilon}^{-m}$, c and m values of each net were compared. As a result, as the model was smaller, c and m values was smaller in the two rule into standard of 1/10 model value, decrease degree of 1/25 model was almost same in the two rule, decrease degree of 1/50 model was very big in Tauti's modeling rule. Therefore, in the result of experiment, because average of c and m values for similarly 1/10 and 1/25 model were given $c=4.9(kgf{\cdot}s^2/m^4)$ and m=0.45, R (kgf) of bottom pair trawl net could show $R=4.9S{\upsilon}^{1.55}$ using these values. As in the order of cod-end, wing and bag part for 1/25 and 1/50 model net were removed in turn, measured flow resistance of each, converted into the full-scale, total resistance of the net and the resistance of each part net were calculated. The resistance ratio of each part for total net was not same in 1/25 and 1/50 model each other, but average of two nets was perfectly same area ratio of each part as the wing, bag and cod-end part was 43%, 45% and 12%. However, the resistance of each part divided area of the part, calculated the resistance of per unit area, wing and bag part were not big difference each other, while the resistance of cod-end part was very large.

• Proceedings of the KSRS Conference
• /
• 2004.10a
• /
• pp.87-90
• /
• 2004

Telematics is an emerging industrial field made up of the convergence of technologies. The key technologies for Telematics are server-side technology, terminal-side technology, communication-related technology, and positioning technology. Standardization in Telematics is now getting more notice these days. Domestic situation is explained for several related facilities such as ETRI, TTA, and Telematics Standardization Forum. In this paper, we will focus especially on the standard reference model that is the most fundamental framework of Telematics technology standardization. In the reference model, the Telematics system is composed of Telematics client part, communication part, and Telematics server part. The Telematics client part consists of terminal, positioning device, and car electronic devices. Communication part can be composed of various telecommunication channels such as CDMA, WLAN, DMB, WiBro, etc. which can guarantee the seamless two-way communication. Telematics server part is composed of TSP(Telematics Service Provider) server and CP(Contents Provider) servers gathering and managing the various Telematics services. This Telematics reference model is expected to be utilized as the base architecture in developing the technology and standards from now on.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.11
• /
• pp.80-85
• /
• 2001

In Part 2, dynamic cutting force model, thermal behavior model, and feed drive model are presented for development of a virtual machine tool. Some relevant results with brief descriptions for each model are presented to verify the proposed models. Experimental results for each model agreed well with the estimated ones. The developed models in this two-part paper are partially integrated as a comprehensive software environment.

• Wind and Structures
• /
• v.25 no.6
• /
• pp.537-549
• /
• 2017

In this study, the turbulent flow around a bluff body for different wind velocities was investigated numerically by using its two- and three-dimensional models. These models were tested to verify the validity of the simulation by being compared with experimental results which were taken from the literature. Variations of non-dimensional velocities in different positions according to the bluff body height were analysed and illustrated graphically. When the velocity distributions were examined, it was seen that the results of both two- and three-dimensional models agree with the experimental data. It was also seen that the velocities obtained from two-dimensional model matched up with the experimental data from the ground to the top of the bluff body. Particularly, compared to the front part of the bluff body, results of the upper and back part of the bluff body are better. Moreover, after comparing the results from calculations by using different models with experimental data, the effect of multidimensional models on the obtained results have been analysed for different inlet velocities. The calculation results from the two-dimensional (2D) model are in satisfactory agreement with the calculation results of the three-dimensional model (3D) for various flow situations when comparing with the experimental data from the literature even though the 3D model gives better solutions.

• Journal of Drive and Control
• /
• v.13 no.3
• /
• pp.1-7
• /
• 2016

A cold gas blow-down hydraulic actuation system is widely used in missiles that require an actuation system with a fast response time under a limited space with a short operating time and large loads on the actuators. The system consists of a pneumatic part that supplies the regulated high-pressure gas to a reservoir, and a hydraulic part that supplies pressurized hydraulic oil to the actuators by the pressurized gas in the reservoir. This paper proposes a mathematical model to analyze and simulate the pneumatic part of an actuation system that supplies the operating power to the actuators. The mathematical model is based on the ideal gas equation and also considers the models for heat transfer. The model is applied to the pressure vessel and the gas part of the reservoir, and the model for the pneumatic part is established by connecting the two models for the parts. The model is validated through a comparison of the simulation results with the experimental results. The comparison shows that the suggested model could be useful in the design of the pneumatic part of a cold gas blow-down type hydraulic actuation system.