• Journal of Korean Society on Water Environment
• /
• v.22 no.5
• /
• pp.905-912
• /
• 2006

In this paper, simulation methods of the system dynamics model developed by Das et al. (1997) for activated-sludge wastewater treatment plants are illustrated in an attempt to determine the operating rules and the policies related to capacity expansion of an activated-sludge wastewater treatment plant. For existing conditions, the analyses were performed by varying activated-sludge return rate to observe changes in effluent water quality and treatment efficiency. The effluent water quality is also analyzed for various average daily inflow conditions and activated-sludge return rates. As a result, without expanding the aeration tank, maximum average daily inflow that can satisfy the effluent water quality standard of BOD $0.02kg/m^3$ was determined as $2,840m^3/hr$, subject to 100% of activated-sludge return rate while other factors remain constant. When the activated-sludge return rate is less than 100%, expansion of the aeration tank is necessary and minimum sizes of the aeration tank to satisfy the effluent water quality standard were determined for various activated-sludge return rates. In addition, the total operating and maintenance as well as unit treatment cost regression equations for activated-sludge wastewater treatment plants are suggested by using the cost data that are obtained from Water and Wastewater Division, Ministry of Environment. The regression analyses showed that the economies of scale phenomena exist in the operating and maintenance costs of activated-sludge wastewater treatment plants.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.2
• /
• pp.61-68
• /
• 2023

Ti and Ti alloys are used in the automobile and aerospace industries due to their high specific strength and excellent corrosion resistance. However their application is limited due to poor formability at room temperature and high unit cost. In order to overcome these issues, dissimilarly jointed materials, such as cladding materials, are widely investigated to utilize them in each industrial field because of an enhanced plasticity and relatively low cost. Among various dissimilar bonding processes, the rolled cladding process is widely used in Ti alloys, but has a disadvantage of low bonding strength. Although this problem can be solved through post-heat treatment, the mechanical properties at the bonded interface are deteriorated due to residual stress generated during post-heat treatment. Therefore, in this study, the microstructure change and residual stress trends at the interfaces of Ti/Al cladding materials were studied with increasing post-heat treatment temperature. As a result, compared to the as-rolled specimens, no difference in microstructure was observed in the specimens after postheat treatment at 300, 400, and 500℃. However, a new intermetallic compound layer was formed between Ti and Al when post-heat treatment was performed at a temperature of 600℃ or higher. Then, it was also confirmed that compressive residual stress with a large deviation was formed in Ti due to the difference in thermal expansion coefficient and modulus of elasticity between Ti Grade II and Al 1050.

• Clinical and Experimental Pediatrics
• /
• v.56 no.4
• /
• pp.145-150
• /
• 2013

Endoscopic treatment is a minimally invasive treatment for managing patients with vesicoureteral reflux (VUR). Although several bulking agents have been used for endoscopic treatment, dextranomer/hyaluronic acid is the only bulking agent currently approved by the U.S. Food and Drug Administration for treating VUR. Endoscopic treatment of VUR has gained great popularity owing to several obvious benefits, including short operative time, short hospital stay, minimal invasiveness, high efficacy, low complication rate, and reduced cost. Initially, the success rates of endoscopic treatment have been lower than that of open antireflux surgery. However, because injection techniques have been developed, a recent study showed higher success rates of endoscopic treatment than open surgery in the treatment of patients with intermediate- and high-grade VUR. Despite the controversy surrounding its effectiveness, endoscopic treatment is considered a valuable treatment option and viable alternative to long-term antibiotic prophylaxis.

• Journal of Periodontal and Implant Science
• /
• v.26 no.3
• /
• pp.689-699
• /
• 1996

The purpose of this research is to determine elements affecting the out-of-pocket cost of woman. The sample consisted of 1907 women living Iksan city. The survey was conducted by means of questionnaires. The model used in the analysis of out-of-pocket cost was the Andersen-Newman model, while the analysis techniques used were stepwise multiple regression and path analysis. The number of independent variables used in the analysis was 28 in total, ie 19 predisposing components, 6 enabling components, and 3 need components. In this study, the amount of variance by the model was 17 percent. Number of restricted activity days caused by oral disease, perceived susceptibility of dental disease, having a regular dental care, dental treatment costs, education level and income were found to have significant major effects on out-of-pocket cost. Number of restricted activity days caused by oral disease was the most important variable affecting out-of-pocket cost of woman. Also out-of-pocket cost shows larger effect due to enabling components than frequency of dental utilization.

• Journal of the Korean Society of Safety
• /
• v.30 no.5
• /
• pp.29-36
• /
• 2015

Common utility tunnel is essential to the daily lives of people underground utilities (electricity, gas and supply facilities such as water, communication facilities, sewer facilities, etc.) to improve the appearance by co-acceptance and disaster prevention, important for the conservation of the city's population was concentrated road construction the city-based facilities. There is recognition of the importance of the various supply treatment facilities in common utility tunnel as infrastructure to accommodate joint according to the city expanded, the demand for infrastructure. In this paper, a cost-benefit analysis using a one-time occurrence, without simply relying on cost or current cost, project manager for the city-dimensional feasibility study conducted, the user level of the maintenance costs and user costs, including social costs items from various angles can be investigated and proposed a mechanism of economic feasibility common utility tunnel. Evaluation of the proposed technique is cost-benefit and cost caused by installing common utility tunnel the existing pipeline area - was investigated by the benefit analysis, extended and repeated common utility tunnel installation depends much affected by the excavation, so users of reducing the number of repeat excavation convenience can be seen that this occurs.

• The Journal of Korean Medicine Ophthalmology and Otolaryngology and Dermatology
• /
• v.23 no.1
• /
• pp.260-269
• /
• 2010

Background : Bojungikgitang(BJT) and Banhabaekchulchonmatang(BBT) are known to treat the tinnitus patients, which were registered Korean National Health Insurance coverage lists. Objective : Few studies have evaluated economic benefits of both herbal medicines. This research is to investigate the cost-effectiveness of Bojungikgitang(BJT) and Banhabaekchulchonmatang(BBT) in chronic tinnitus patients over nineteen years old. Method : We built the decision tree model of chronic tinnitus and executed the deterministic analysis and threshold sensitivity analysis based on randomized clinical trial. Effectiveness was measured in quality-adjusted life-years(QALYs), and costs were in 2009 KRW(South Korean Currency). The perspective is societal, time horizon is 10 weeks, and Korean willingness to pay threshold is assumed to 20,000,000KRW. Results : In the base case analysis, BJT treatment resulted is better outcomes as low cost, so BJT is dominant medicine and BBT is dominated. But both cost per QALYs (BJT is 3,120,339KWN per QALY, BBT is 3,505,780KWN per QALY) are lower than the threshold, that could be covered by Korean National Health Insurance(KNHI). Conclusion : This study results showed that BJT was more cost-effective than BBT treating tinnitus patients for 10 weeks, and the cost per QALYs of both alternatives were lower than Korean national threshold.

• Environmental Analysis Health and Toxicology
• /
• v.30 no.sup
• /
• pp.6.1-6.4
• /
• 2015

Objectives This study is conducted to estimate the cost paid by the public suffering from disease possibly caused by chemical and to examine the effect on public health. Methods Cost-benefit analysis is an important factor in analysis and decision-making and is an important policy decision tool in many countries. Cost-of-illness (COI), a kind of scale-based analysis method, estimates the potential value lost as a result of illness as a monetary unit and calculates the cost in terms of direct, indirect and psychological costs. This study estimates direct medical costs, transportation fees for hospitalization and outpatient treatment, and nursing fees through a number of patients suffering from disease caused by chemicals in order to analyze COI, taking into account the cost of productivity loss as an indirect cost. Results The total yearly cost of the diseases studied in 2012 is calculated as 77 million Korean won (KRW) per person. The direct and indirect costs being 52 million KRW and 23 million KRW, respectively. Within the total cost of illness, mental and behavioral disability costs amounted to 16 million KRW, relevant blood immunological parameters costs were 7.4 million KRW, and disease of the nervous system costs were 6.7 million KRW. Conclusions This study reports on a survey conducted by experts regarding diseases possibly caused by chemicals and estimates the cost for the general public. The results can be used to formulate a basic report for a social-economic evaluation of the permitted use of chemicals and limits of usage.

• Journal of Korean Society of Water and Wastewater
• /
• v.31 no.6
• /
• pp.529-537
• /
• 2017

Membrane filtration process is an advanced water treatment technology that has excellently removes turbidity and microorganisms. However, it is known that it has problems such as low economic efficiency and the operating stability. Therefore, this study was to evaluate on the economical feasibility and operational stability comparison of membrane and sand filtration process in Im-sil drinking water treatment plant. For the economic analysis of each process, the electricity cost and chemical consumption were compared. In the case of electric power consumption, electricity cost is $68.67KRW/m^3$ for sand filtration and $79.98KRW/m^3$ for membrane filtration, respectively. Therefore, membrane filtration process was about 16% higher than sand filtration process of electricity cost. While, the coagulant usage in the membrane filtration process was 43% lower than the sand filtration process. Thus, comparing the operation costs of the two processes, there is no significant difference in the operating cost of the membrane filtration process and the sand filtration process as $85.94KRW/m^3$ and $79.71KRW/m^3$ respectively (the sum of electricity and chemical cost). As a result of operating the membrane filtration process for 3 years including the winter season and the high turbidity period, the filtrated water turbidity was stable to less than 0.025 NTU irrespective of changes in the turbidity of raw water. And the CIP(Clean In Place) cycle turned out to be more than 1 year. Based on the results of this study, the membrane filtration process showed high performance of water quality, and it was also determined to have the economics and operation stability.

• Journal of Korean society of Dental Hygiene
• /
• v.15 no.5
• /
• pp.899-905
• /
• 2015

Objectives: This study aimed to investigate the regional difference of chronic periodontal care services in Korea by the analysis of 2010 raw data from Health Insurance Review and Assessment Service. Methods: The subjects were the chronic periodontitis patients over 35 years old from dental care facilities in Korea. The study population was 278,319 including 264,994 claims made by dental clinics, 8,084 by dental hospitals, 3,509 by general hospitals, and 1,732 by tertiary hospitals. Results: There was a significant difference in medical care cost benefit between the provinces(p<0.0001). The age groups showed a clear difference in the patient charge, cost of insurance, and medical care cost benefit(p<0.0001). In consideration of the first visit or revisit, there were differences in the rate of prescription, dental examination, and surgical procedures of the chronic periodontal patients from dental facilities. The radiographic use rate in the tertiary hospitals was 2.6 times higher than that of the dental clinic in the treatment of the new chronic periodontal patients. Conclusions: The use of dental services in the periodontitis is influenced by the types of medical services facility, cost of medical insurance, and patient charge. In consideration of cost benefit analysis, prevention is the most important care for the periodontitis. Regional difference in peridontitis is cause by the use of medical services and quality of treatment.

• Korean Journal of Materials Research
• /
• v.25 no.11
• /
• pp.636-641
• /
• 2015

Titanium has many special characteristics such as specific high strength, low elastic modulus, excellent corrosion and oxidation resistance, etc. Beta titanium alloys, because of their good formability and strength, are used for jet engines, and as turbine blades in the automobile and aerospace industries. Low cost beta titanium alloys were developed to take economic advantage of the use of low-cost beta stabilizers such as Mo, Fe, and Cr. Generally, adding a trace of boron leads to grain refinement in casted titanium alloys due to the pinning effect of the TiB phases. This study analyzed and evaluated the microstructural and mechanical properties after plastic deformation and heat treatment in boron-modified Ti-2Al-9.2Mo-2Fe alloy. The results indicate that a trace of boron addition made grains finer; this refinement effect was found to be maintained after subsequent processes such as hot forging and solution treatment. This can effectively reduce the number of required manufacturing process steps and lead to savings in the overall cost as well as low-cost beta elements.