• 한국생산제조학회지
• /
• 제20권3호
• /
• pp.257-262
• /
• 2011

A low capacity generator converted to high capacity of 40m3 is designed and developed in order to use the hydroxy gas in the steel manufacturing process. For efficient design, it is increased from 8 electrode tubes to 10 electrode tubes as well as expanding the diameter of cell integument up to two times bigger, which can increase the amount of hydrogen occurrence per a cell significantly. In addition, circulating pump and pipe, heat exchanger of affiliated SUS material have been used in the circulation of electrolysis catalyst, and circulating cooling section and piping design are also developed. The flame trap is designed into all-in-one suitable check valve in the flow rate of 28-35m3/h and its application is possibly applied in work operation. It is found that the efficiency of generator developed is enhanced substantially up to 84%. It is expected that the application in this field can be expanded significantly by this study.

• 한국수자원학회논문집
• /
• 제36권6호
• /
• pp.1059-1068
• /
• 2003

본 연구는 아산만으로 유입되는 유사량을 추정하기 위하여 Landsat-5 TM 위성영상과 NGIS 수치자료를 이용하여 대상유역의 기본도와 USLE 주제도를 구축하고, 범용토양유실공식(USLE)을 이용하여 아산만 유역의 토양유실량을 추정하였다. 유사운송비와 포착률을 이용하여 아산만으로 유입되는 유사량을 추정하였으며, 이를 농업기반공사의 배수갑문 관리자료와 환경부의 담수호 부유물 측정자료로부터 구한 실측 유사량과 비교하였다. USLE와 유사운송비, 포착률을 이용해 추정된 값과 실측 유입유사량을 비교한 결과, 아산호의 경우 연평균 추정치는 5,665tonnes/yr, 실측치는 12,937tonnes/yr, 삽교호의 경우 추정치는 6,765tonnes/yr, 실측치는 12,395 tonnes/yr 으로 나타났다.

• 한국자동차공학회논문집
• /
• 제24권3호
• /
• pp.345-351
• /
• 2016

This study was carried out to determine an optimal lean $NO_x$ trap (LNT) regeneration condition based on a $NO_x$ storage fraction. The LNT regeneration was performed by an in-cylinder post fuel injection method. A $NO_x$ storage fraction is defined by the ratio of current cumulated $NO_x$ amount in the LNT to the $NO_x$ storage capacity: 0 means empty and 1 fully loaded. In this study five engine operating conditions were chosen to represent the New European Driving Cycle. With various $NO_x$ storage fractions each engine operating condition, the LNT regeneration was executed and then $NO_x$ conversion efficiency, additional fuel consumption, CO and THC slip, peak catalyst temperature were measured. The results showed that there exist an optimal condition to regenerate the LNT, eg. 1500 rpm 6 bar BMEP with below 0.7 $NO_x$ storage fraction in this experimental constraint.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2019년도 학술발표회
• /
• pp.247-247
• /
• 2019

수력발전 사업에 있어 Desander 구조물은 주로 고산지대 수력발전댐의 Run-of-river 형식의 발전방식에서 유사로 인한 터빈의 손상을 방지하기 위한 목적으로 설치된다. Desander의 적정 규모는 터빈의 손상을 일으킬 수 있는 유사 입경에 대해 안정적으로 침전을 시킬 수 있는 폭/길이/깊이로 평가할 수 있으며 상대적으로 Desander의 규모가 크게 설계된 경우 초기 공사비 증가하고 반대로 규모가 작게 설계된 경우 터빈의 교체 주기 단축으로 인한 유지관리비가 증가된다. 현재까지 일반적인 Desander 구조물의 설계 방식은 제거 입경의 침전 속도, 유입유량 및 깊이를 변수로 사용하여 경험식(L. Sudry method, Guicciardis method 및 Rouse method)을 통해 규모를 결정해 왔다. 하지만, 3-D 전산유체해석을 통해 유속 흐름 분석으로 직 간접적 Desander 규모의 적정성을 평가할 수 있는 현 시점에서 경험식으로부터 도출된 결과의 신뢰성과 객관성을 검증할 필요가 있다고 판단된다. 본 연구에서는 노르웨이 NSTU에서 개발한 유사의 이송 및 확산해석 기능이 내장된 범용 소프트웨어인 SSIIM을 이용하였다. SSIIM(Simulation of Sediment movements In water Intakes with Multiblock)은 개수로 흐름 상태에서 유사 이동 및 하상 변동을 분석할 수 있도록 개발된 3-D 해석 프로그램이다. SSIIM은 수치해석 방법으로 유한체적법(Finite Volume Method)를 채택하였으며 Navier-Stokes equations을 통해 유체의 흐름을 해석한다. 입력 자료는 유입 유량($m^3/sec$), 유입 유사량(kg/sec), 유출부 수위 및 해당 Desander Structure grid 자료가 사용되며 해석 결과로 Desander 내 grid 별 유속, 수위, 유사 농도 변화 등을 제공한다. 본 연구에서는 SSIIM을 이용하여 제거 목표 유사 입경의 차집 효율(Trap efficiency)로 Desander의 적정 규모를 평가 할 수 있는 설계법을 제안하며 설계 단계에서 결정되는 최소 제거유사 입자와 차집 효율에 의한 Desander의 적정 규모 평가 분석을 파키스탄 A 프로젝트를 대상으로 수행하였다. 연구 성과로 (1)SSIIM을 통해 해석된 차집 효율을 기초로 Desander의 적정 규모를 계획할 경우 경험적 방식에 비해 설계의 객관성과 신뢰성을 제고할 수 있으며 (2)3-D 수치해석을 통해 grid 별 유사농도를 확인 할 수 있어 Desander 형상과 규모에 대한 평가가 가능하다.

• 한국토양비료학회지
• /
• 제50권6호
• /
• pp.554-561
• /
• 2017

Under the projected global warming, release of carbon as $CO_2$ through soil organic matter decomposition is expected to increase. Therefore, accurate measurement of $CO_2$ released from soil is crucial in understanding the soil carbon dynamics under increased temperature conditions. Sodium hydroxide (NaOH) traps are frequently used in laboratory soil incubation studies to measure soil respiration rate, but decreasing $CO_2$ gas solubility with increasing temperature may render the reliability of the method questionable. In this study, the influences of increasing temperature on the $CO_2$ capture capacity of NaOH traps were evaluated under $5{\sim}35^{\circ}C$ temperature range at $10^{\circ}C$ interval. Two closed-chamber experiments were performed where NaOH traps were used to capture $CO_2$ either released from acidified $Na_2CO_3$ solution or directly injected into the chamber. The sorption of ambient $CO_2$ within the incubators into NaOH traps was also measured. The amount $CO_2$ captured increased as temperature increased within 2 days of incubation, suggesting that increased diffusion rate of $CO_2$ at higher temperatures led to increases in $CO_2$ captured by the NaOH traps. However, after 2 days, over 95% of $CO_2$ emitted in the emission-absorption experiment was captured regardless of temperature, demonstrating high $CO_2$ absorption efficiency of the NaOH traps. Thus, we conclude that the influence of decreased $CO_2$ solubility by increased temperatures is negligible on the $CO_2$ capture capacity of NaOH traps, supporting that the use of NaOH traps in the study of temperature effect on soil respiration is a valid method.

• 한국환경보건학회지
• /
• 제25권3호
• /
• pp.103-107
• /
• 1999

Even if odorous compounds remain very low concentration in water, it cause strong odor. Because Geosmin and most of odorous compound had very low vaporization, those were difficult to analyze with GC/MSD and Purge & Trap. So, we needed pre-treatment method for decreasing amounts of extracting solvents, improving recovery efficiencies and increasing analytical efficiencies. This study developed efficient technology for analyzing odorous compounds, using various adsorbents and extracting solvents. The optimum adsorbent was XAD resins. Especially, XAD-2, XAD-7 and XAD-2010 were superior, but XAD-2 of these and the optimum extraction solvent is MTBE. Other extraction solvents' efficiency is in order of MTBE>Dichloromethane>n-Hexane>Diethylether. The optimum NaCl dosage for increasing efficiency is 5 g in liquid-liquid extraction method. The shaking time(0~24hr) has no concern with adsorption efficiency. The optimum adsorbent is XAD-2 resin and extraction solvent is MTBE. Dosing NaCl, adsorption efficiency is increased in liquid-liquid extraction method, but NaCl has no effect on liquid-solid extraction method. In this experimental results, this algae toxins(Mycrocystin, Anatoxin etc.).

• 생명과학회지
• /
• 제9권5호
• /
• pp.575-580
• /
• 1999

Even if odorous compounds remained very low concentration in water, it caused strong odor. Because Geosmin and most of odorous compound had very vaporization, those were difficult to analyze with GC/MSD and Purge & Trap. So, we needed pre-treatment method for decreasing amounts of extracting solvents, improving recovery efficiencies and increasing analytical efficiencies. This study developed efficient technology for analyzing odorous compounds, using various adsorbents and extracting solvents. The optimum adsorbent was XAD resins. Especially, XAD-2, XAD-7 and XAD-2010 were superior, but XAD-2 of these and MTBE was the optimum extraction solvent. Other extraction solvent's efficiency was in order of MTBE>Dichloromethane>n-Hexane>Diethylether. The optimum NaCl dosage for increasing efficiency was 5g in liquid-liquid extraction method. The shaking time(0∼24hr) had no concern with adsorption efficiency. The optimum adsorbent was XAD-2 resin and extraction solvent was MTBE. Dosing NaCl, adsorption efficiency was increased in liquid-liquid extraction method, but NaCl has no effect on liquid-solid extraction method. In this experimental results, this method will apply to not only Geosmin but other well-known odorous compounds (2-MIB, IBMP, IPMP, TCA) and algae toxins (Mycrocystin, Anatoxin etc)

• 한국자동차공학회논문집
• /
• 제16권6호
• /
• pp.176-183
• /
• 2008

Performance of electrostatic diesel PM filtration systems (E-DPS) with different types has been tested using the carbon particles generated by spark discharge in laboratory. Among the five electrostatic precipitators, the multiple wires cylindrical E-DPS with the highest collection efficiency and relatively lower differential pressure at the flow rate of $1\;m^3$/min, as an applicable device to diesel engine as an after treatment system, has been combined with another collection cylinder to improve the collection efficiency of diesel particulate matters generated from diesel engines. The multiple wires cylindrical E-DPS combined with the cylindrical collector showed the collection efficiency of more than 60% at the engine speed of 2,000 rpm with the engine loads of 25 and 50%.

• Korean Chemical Engineering Research
• /
• 제45권3호
• /
• pp.264-268
• /
• 2007

마이크론 금속섬유 필터 표면상에 탄소나노튜브를 직접 합성 성장함으로써 마이크론 필터의 성능을 향상할 수 있었다. 탄소나노튜브는 합성조건에 따라 마이크론 섬유 주위를 덮는 덤불 나노구조체 또는 섬유 사이를 연결하는 망 형상의 나노구조체로 성장하였다. 탄소나노튜브가 성장한 금속필터와 탄소나노튜브가 성장하지 않은 금속필터의 여과성능을 측정하여 비교한 결과, 차압의 변화는 미미하나 여과효율은 더욱 향상되었고, 이는 탄소나노튜브가 오염 나노입자를 잡는 트랩으로 작용하였기 때문이다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.802-806
• /
• 2001

Diesel particulate trap is the most reliable system to reduce the particulate matters from diesel engine. Filter is the core component of DPF and ceramic monolith type is dominantly used, which is expensive and fragile relatively at thermal shock. Porous metal filter, which has superior thermal characteristics and low cost, was tested in order to analyze the regeneration performance by using with ferrocene additive. This filter showed the 72% filtration efficiency, additives itself diminished 48% of PM from engine out emission, and final PM reduction ratio of 89% was achieved by DPF system with D-13 test mode.