• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.5
• /
• pp.55-62
• /
• 2019

In this paper, we consider K-user multiple-input multiple-output (MIMO) interference channel and present a transceiver design for simultaneous wireless information and power transfer (SWIPT) systems. In addition, we consider a SWIPT system where an information decoding receiver and an energy harvesting receiver are co-located at the same receiver. In the proposed scheme, signal-to-leakage plus noise ratio (SLNR) is used as a cost function and a transceiver is designed to satisfy the threshold of the harvested energy. More specifically, transmitter precoding vector, receiver filter vector, and power spitting factor are simultaneously designed to maximize SLNR with a constraint on the harvested energy. Through computer simulation, we compare the signal-to-interference plus noise ratio (SINR) performance of the proposed and conventional schemes. When a special condition among the number of transmit antennas, receive antennas, and users is satisfied, the proposed scheme showed better SINR performance than the conventional scheme at low signal-to-noise ratio (SNR) range. Also, when the condition is not satisfied, the proposed scheme showed better performance than the conventional scheme at all SNR range.

• Journal of Advanced Navigation Technology
• /
• v.24 no.6
• /
• pp.566-572
• /
• 2020

In a wireless power transmitter, the characteristics and effects of wireless power transmission between two induction coils are investigated, and a power converter circuit and a battery charger/discharger circuit using wireless power transmission technology are proposed. The advantage of wireless power transmitters and wireless chargers is that, instead of the existing plug-in-mounted wired charger (OBC; on-board charger), the user can wirelessly charge the battery without connecting the power source when charging power to the battery. There is. In addition, the advantage of wireless charging can bring about an energy efficiency improvement effect by using the secondary side rectifier circuit and the receiving coil, but the large-capacity long-distance wireless charging method has a limitation on the transmission distance, so many studies are currently being conducted. The purpose of the study is to study the transmitter circuit and receiver circuit of a wireless power transmission device using a primary coil, a secondary coil, and a half bridge series resonance converter, which can transmit power of a non-contact type power transmitter. As a result, a new topology was applied to improve the power transmission distance of the wireless charging system, and through an experiment according to each distance, the maximum efficiency (95.8%) was confirmed at an output of 3 kW at an 8 cm transmission distance.

• Journal of Advanced Navigation Technology
• /
• v.12 no.3
• /
• pp.208-214
• /
• 2008

With the development of the automobile industry, technologies for parts of an automobile with more convenient functions have progressed, but the manual clutch developed at the first phase of inventing means of transport still remains at the early stage of the automatic transmission despite numerous research and efforts. The traditional automatic transmission is mainly used in small cars and personal RV vehicles that include the slipped clutch disk. However, this research seeks an innovative technology that can be applied to all types of transportation operating the clutch, such as small cars, large vehicles, farm machines and vessels. In order to accurately decide the joint timing of the clutch disk according to the output of engine power that differs depending on driving conditions of vehicles, and to apply the half clutch state which frequently occurs in the manual transmission, the rpm of the engine can be used as the base to decide the joint timing of the clutch disk. This research has developed an electronic clutch module that can transmit the engine power by moving and jointing the clutch disk as much as the engine rpm increases.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.12
• /
• pp.1380-1393
• /
• 2010

This paper presents a design, fabrication and the test results of planar active electronically scanned array(AESA) radar prototype for airborne fighter applications using transmit/receive(T/R) module hybrid technology. LIG Nex1 developed a AESA radar prototype to obtain key technologies for airborne fighter's radar. The AESA radar prototype consists of a radiating array, T/R modules, a RF manifold, distributed power supplies, beam controllers, compact receivers with ADC(Analog-to-Digital Converter), a liquid-cooling unit, and an appropriate structure. The AESA antenna has a 590 mm-diameter, active-element area capable of containing 536 T/R modules. Each module is located to provide a triangle grid with $14.7\;mm{\times}19.5\;mm$ spacing among T/R modules. The array dissipates 1,554 watts, with a DC input of 2,310 watts when operated at the maximum transmit duty factor. The AESA radar prototype was tested on near-field chamber and the results become equal in expected beam pattern, providing the accurate and flexible control of antenna beam steering and beam shaping.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.10 no.8
• /
• pp.3529-3550
• /
• 2016

In heterogeneous networks (HetNets), energy saving is vital for a sustainable network development. Many techniques, such as spectrum allocation, network planning, etc., are used to improve the network energy efficiency (EE). In this paper, micro BSs utilizing cell range expansion (CRE) and spectrum allocation are considered in multi-channel heterogeneous networks to improve EE. Hotspot region is assumed to be covered by micro BSs which can ensure that the hotspot capacity is greater than the average demand of hotspot users. The expressions of network energy efficiency are derived under shared, orthogonal and hybrid subchannel allocation schemes, respectively. Particle swarm optimization (PSO) algorithm is used to solve the optimal ratio of subchannel allocation in orthogonal and hybrid schemes. Based on the results of the optimal analysis, we propose three service control strategies on the basis of large-scale user behaviors, i.e., adjust micro cell rang expansion (AmCRE), adjust micro BSs density (AmBD) and adjust micro BSs transmit power (AmBTP). Both theoretical and simulation results show that using shared subchannel allocation scheme in AmBD strategies can obtain maximal EE with a very small area ratio. Using orthogonal subchannel allocation scheme in AmCRE strategies can obtain maximal EE when area ratio is larger. Using hybrid subchannel allocation scheme in AmCRE strategies can obtain maximal EE when area ratio is large enough. No matter which service control strategy is used, orthogonal spectrum scheme can obtain the maximal hotspot user rates.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.12 no.3
• /
• pp.1-10
• /
• 2013

Most of the current traffic signal controller use load switches to transmit high voltage power to the signal lamps. The direct transmission of high voltage power may cause a lot of problems like leakages of electric power, obstructions of pedestrian, environmental disfigurements. To overcome these problems, the development of digital type signal controller has been trying in the various methods. Digital communication between a master controller and signal lamps is the most important part to improve control performance in the digital type controller. A communication system for the digital signal controller was developed in this study. The system bases on CAN specification, includes ID structure for most peripheral devices like loops, signal lamps, push buttons, police switches. The operability of this system verified with a software based CAN simulation tool.

• Journal of Communications and Networks
• /
• v.15 no.5
• /
• pp.476-485
• /
• 2013

In this paper, the effective capacity of a multiple-input multiple-output (MIMO) system in two different cases with receive antenna selection (RAS) and transmit antenna selection (TAS) schemes is investigated. A closed-form solution for the maximum constant arrival rate of this network with statistical delay quality of service (QoS) constraint is extracted in the quasi-static fading channel. This study is conducted in two different cases.When channel state information (CSI) is not available at the MIMO transmitter, implementation of TAS is difficult. Therefore, RAS scheme is employed and one antenna with the maximum instantaneous signal to noise ratio is chosen at the receiver. On the other hand, when CSI is available at the transmitter, TAS scheme is executed. In this case, one antenna is selected at the transmitter. Moreover, an optimal power-control policy is applied to the selected antenna and the effective capacity of the MIMO system is derived. Finally, this optimal power adaptation and the effective capacity are investigated in two asymptotic cases with the loose and strict QoS requirements. In particular, we show that in the TAS scheme with the loose QoS restriction, the effective capacity converges to the ergodic capacity. Then, an exact closed-form solution is obtained for the ergodic capacity of the channel here.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.14 no.6
• /
• pp.2709-2734
• /
• 2020

The growing demand to make wireless data services 5G compatible has necessitated the development of an energy-efficient approach for an effective new wireless environment. In this paper, we first propose a cognitive sensor node (CSN) based game theory for deriving energy via a primary user-transmitted radio frequency signal. Cognitive users' time was segmented into three phases based on a time switching protocol: energy harvest, spectrum sensing and data transmission. The proposed model chooses the optimal energy-harvesting phase as the effected factor. We further propose a distributed energy-harvesting model as a utility function via pricing techniques. The model is a non-cooperative game where players can increase their net benefit in a selfish manner. Here, the price is described as a function pertaining to transmit power, which proves that the proposed energy harvest game includes Nash Equilibrium and is also unique. The best response algorithm is used to achieve the green connection between players. As a result, the results obtained from the proposed model and algorithm show the advantages as well as the effectiveness of the proposed study. Moreover, energy consumption was reduced significantly (12%) compared to the benchmark algorithm because the proposed algorithm succeeded in delivering energy in micro which is much better compared to previous studies. Considering the reduction and improvement in power consumption, we could say the proposed model is suitable for the next wireless environment represented in 5G.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.380-388
• /
• 2016

Using the magnet gear, it is possible to transmit power without mechanical contact. As the drive shaft in a magnet gear-based speed reducer system is isolated from the drive shaft, the system is a two-inertia resonance system that should cope with an external load with the limited air-gap stiffness. On the other hand, the drive shaft or low-speed side is controlled only by the torque of the drive shaft through an air-gap, and the excessive oscillation or the slip can then be generated because of an abrupt disturbance that is different from the general mechanical gear system. Therefore, the disturbance loaded at the low speed side should be measured or estimated, and considered in the control of the driving shaft. This paper proposes a novel full-state feedback controller with a reduced-order observer for the speed reducer system using a magnet gear with a unified harmonic modulator. The control method was verified by simulation and experiment. To estimate the load at the low speed side, a novel observer was designed, in which the new state variable is introduced and the new state equation is formulated. Using a full-state feedback controller including the observer, the test result against disturbance was compared with two D.O.F PI speed controllers. The pole slip was compensated within relatively a short time, and the simulation result about the estimated variable shows a similar tendency to the test result. The test results showed that the magnet gear-based reducer can be applied to an accurate servo system.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.3
• /
• pp.273-281
• /
• 2019

The energy consumed by buildings among the total national energy consumption is more than 10% of the total. For this reason, Korea has adopted the zero energy building policy since 2025, and research on the energy saving technology of buildings has been demanded. Analysis of buildings' energy consumption patterns shows that lighting, heating and cooling energy account for more than 60% of total energy consumption, which is directly related to solar power acquisition and window opening and closing operation. In this paper, we have developed a low - power IoT sensor module for window system to transfer acquired information to building energy management system. This module transmits the external environment and window opening / closing status information to the building energy management system in real time, and constructs the network to actively take energy saving measures. The power used in the module is designed as an independent power source using solar power among the harvest energy. The topology of the power supply is a Buck converter, which is charged at 4V to the lithium ion battery through MPPT control, and the efficiency is about 85.87%. Communication is configured to be able to transmit in real time by applying WiFi. In order to reduce the power consumption of the module, we analyzed the hardware and software aspects and implemented a low power IoT sensor module.