• International Journal of Air-Conditioning and Refrigeration
• /
• 제10권2호
• /
• pp.106-115
• /
• 2002

The performance of an inverter-driven water-to-water heat pump with an electronic expansion valve (EEV) was measured as a function of compressor frequency, load conditions, and EEV opening. Based on the test results, a controller using proportional integral (PI) feedback or PI feedforward algorithm was designed and tested to investigate capacity modulation and transient response control of the system. Although the relation between superheat and EEV opening of the heat pump showed nonlinear characteristics, a control gain obtained at the rated frequency was applicable to various operating conditions without causing large deviations. When the simple PI feedback control algorithm was applied, a large overshoot of superheat and wet compression were observed due to time delay effects of compressor frequency. However, applying PI feedforward control scheme yielded better system performance and higher reliability, compared to the PI feedback algorithm.

• 제어로봇시스템학회논문지
• /
• 제11권12호
• /
• pp.1077-1082
• /
• 2005

In this paper, it is proposed that the method for constituting pressure control system controlled by Direct Drive Valve (DDV). The DDV has a pressure-feedback-loop itself. It can eliminate non-linearity and uncertainty oi hydraulic system such as uncertain discharge coefficient and change of bulk-modulus. However, the internal feedback-loop can not compensate them perfectly. And fixed gain of the DDV's internal feedback-loop is not proper to apply it through wide pressure range. The steady state error and nonlinear characteristic of transient behaviour is observed in the experiment. So another controller is needed for the desirable performance of the system. To compose the controller, the pressure control system controlled by DDV is modeled mathematically and the parameters of the model are identified using signal-compression method. Then sliding mode controller is designed based on mathematical model. Desirable performance of the pressure control system controlled by DDV is obtained.

• 전력전자학회논문지
• /
• 제2권2호
• /
• pp.29-34
• /
• 1997

본 논문에서는 단상 PWM 컨버터의 입력전류 제어계와 출력전압 제어계의 안정한 PI 이득을 설계하고 DSP를 이용하여 순시 제어기를 구현한다. DC link 전압 제어기는 연속영역에서 설계하여도 무방하나 입력전류 제어계는 이산화 영향을 무시할 수 없으므로 입력전류 제어계를 연산 시간을 고려하여 이산 영역에서 전달 함수를 구하여 설계한다. 또한 리플전압 추정 루틴을 통하여 실제 커패시터의 정전용량을 알아내는 알고리듬을 제시하고 이 알고리듬에 의하여 DC link 정전 용량을 과도상태에서도 추정해 낼수 있음을 보인다. 실험에 의하여 입력역률 99%와 부하급변시 전압 변동률 $\pm$5% 이하의 결과를 얻었다.

• 전기학회논문지P
• /
• 제57권3호
• /
• pp.244-249
• /
• 2008

This paper deals with speed control of DC servo motor using a Fuzzy tuning observer. Speed sensor detect a speed of rotor continuously. But it have a limit as a driving speed to detect speed precisely. So it is problem to improve the performance of the driving system. To solve the problem, it is studied to detect a speed of DC motor without sensor. In particular, study on the method to estimate the speed using the observer is performed a lot. In this parer, the gain of the observer is properly set up using the fuzzy observer. The fuzzy observer has a superior transient characteristic and is easy to implement compared the existing method is designed. It estimate the derivative of the armature current directly using the armature current measured in the DC motor. It estimate the speed of the rotor using the differentiation. It is proposed speed sensorless control method using the estimated speed. Optimal gain of Luenberger observer is set up using the fuzzy observer and adapted speed control of DC servo motor low speed operation. It is proved excellence and feasibility of the presented observer from the comparison tested a case with a speed sensor and a case without a speed sensor which used a highly efficient drive and 200W DC servo motor starting system.

• 제어로봇시스템학회논문지
• /
• 제2권2호
• /
• pp.115-120
• /
• 1996

In this paper, a sliding mode controller which is characterized by high accuracy, fast response and robustness is applied to speed control of AC-SERVO motor. The control input is changed to the continuous one in the boundary layer to reduce the chattering phenomenon, and the boundary layer converges to zero when the state variables of system reach to steady state values. The integral compensator is added to reduce steady state error and to provide the continuous torque reference. The acceleration which is necessary for the sliding plane is estimated by an obsever. Sliding surface is included in control input to enhance the robustness and transient response without increasing sliding mode controller gain. The proposed controller is implemented by DSP(digital signal processor). The effectiveness of the proposed scheme is demonstrated through experimental works.

• 제어로봇시스템학회논문지
• /
• 제2권1호
• /
• pp.60-66
• /
• 1996

Model Based Predictive Control(MBPC) has been widely used in predictive control since 80's. GPC[1] which is the superset of many MBPC strategies a popular method, but GPC has some weakness, such as insufficient stability analysis, non-applicability to internally unstable systems. However, CRHPC[2] proposed in 1991 overcomes the above limitations. So we chose RHPC based on CRHPC for electric furnace control. An electric furnace which has nonlinear properties and large time delay is difficult to control by linear controller because it needs nearly perfect modelling and optimal gain in case of PID. As a result, those controls are very time-consuming. In this paper, we applied RHPC with equality constraint to electric furnace. The reults of experiments also include the case of RHPC with monotonic weighting improving the transient response and including unmodelled dynamics. So, This paper proved the practical aspect of RHPC for real processes.

• Journal of Mechanical Science and Technology
• /
• 제15권6호
• /
• pp.699-708
• /
• 2001

This paper presents a new approach to the AFR (Air-to-Fuel Ratio) control problem, which is based on the wide-band oxygen sensor output. The dedicated nonlinear controller is based on the feedback lineaization technique. It is well known that the feedback linearizing control technique requires an exact model of the plant for the cancellation of plant nonlinearities. A sliding mode control scheme is applied which can effectively compensate the modeling uncertainties. The measurement time delay of an oxygen sensor limits the gain of the feedback controller. Hence, time delay compensation procedure is necessary for the improvement of control performance. The Smith predictor is adopted to compensate the effects of time delay. The simulation and experimental results show that the proposed controllers can effectively reduce the transient peaks of AFR in spite of fast tip-in and tip-out maneuvers of the throttle.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1994년도 Proceedings of the Korea Automatic Control Conference, 9th (KACC) ; Taejeon, Korea; 17-20 Oct. 1994
• /
• pp.449-454
• /
• 1994

This paper describes new PID control methods based on the fuzzy logic. PID gains are retuned after evaluating control performances of transient responses in terms of performance features. The retuning procedure is based on fuzzy rules and reasoning accumulated from the knowledge of experts on PID gain scheduling. For the case that the retuned PID gains result in worse CLDR (characteristics of load disturbance rejection) than the initial gains, an on-line tuning scheme of the set-point weighting parameter is, proposed. This is based on the fact that the set-point weighting method efficiently reduce either overshoot or undershoot without any degradation of CLDR. The set-point weighting parameter is adjusted at each sampling instant by the fuzzy rules and reasoning. As a result, better control performances were achived in comparison with die controllers tuned by the Z-N (Ziegler-Nichols) parameter tuning formula or by the fixed set-point weighting parameter.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 B
• /
• pp.504-506
• /
• 1999

In this paper, we propose a method which control parametric uncertainty systems using PID controller by fuzzy auto tuning. We get the error and the error change rate of plant output correspond to the initial value of parameter using the Ziegler-Nickols tuning and determine the new proportional gain$(K_p)$ and the integral time $(T_i)$ from fuzzy tuner by the error and error change rate of plant output as a membership function of fuzzy theory. The Fuzzy Auto-tuning algorithm for PID controller operate to adapt variable parameter of plant in parametric uncertainty systems. It is shown this method considerably improve the transient response at computer simulation.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1995년도 Proceedings of the Korea Automation Control Conference, 10th (KACC); Seoul, Korea; 23-25 Oct. 1995
• /
• pp.215-218
• /
• 1995

In this paper, a sliding mode controller (SMC) which can be characterized by high accuracy, fast response and robustness is applied to speed control of AC-SERVO motor. The control input is changed to continuous one in the boundary layer to reduce the chattering phenomenon, and the boundary layer converges to zero when the state variables of system reach to steady state values. The integral compensator is added to reduce steady state error and to provide the continuous torque reference. The acceleration which is necessary to get the sliding plane is estimated by an observer. Sliding surface is included in control input to enhance the robustness and transient response without increasing sliding mode controller gain. The proposed controller is implemented by DSP(digital signal processor). The effectiveness of the proposed control scheme for speed controller is shown by the real-time experimental results in the paper.