• Magazine of the Korean Society of Agricultural Engineers
• /
• v.11 no.4
• /
• pp.1803-1809
• /
• 1969

The newly designed mole drainage plower which is attached to tractor is tested for work capacity comparing with the pulling by man animal and winch. Besides. the effect of desalinization by the mole drainage in reclaimed tideland was observed. The results as obtained in this experiment are as follows: 1. The mole drainage plower of tractor attachment has higher work capacity by 3 to 5 times than that of winch 2. The suitable soil moisture content to carry out the layout of mole drains is from 21 to 25 percent. 3. The new design mole drainage plower requires th lowest cost as comparing with the other methods. 4. Carrying out the mole drainage in reclaimed tideland it is effective in desalinization from 2 to 3 times than the only use of irrigation water. 5. The reasonable depth and interval of mole drains may be 60cm and 3m respectively. 6. The desalinization by the mole drainage increases the yield of rice from 40 to 45 percent in reclaimed tideland.

• Journal of Korean Society of Forest Science
• /
• v.108 no.4
• /
• pp.574-581
• /
• 2019

The present study analyzed the productivity and cost of winching operations for evaluating the efficiency of a tractor-attached winch in a Pinus densiflora thinning site located in the Yangyang County of Gangwon-do. The mean yarding distance and mean timber volume were 29 m and 0.15 ㎥, respectively. In the 95 cycles of yarding operations, the uphill and downhill yarding operations constituted 51% and 49%, respectively, of the total yarding operations. The productivity of the uphill yarding operation was 2.28 ㎥/h, and the productivity of the downhill yarding operation was 1.89 ㎥/h. The findings of this study revealedthat productivity would increase by 0.5 ㎥/h when the rate of utilization of the machine is increased to 80% by reducing the operational delay time. The cost of the downhill yarding operation was 44,116 KRW/㎥, whereas that of the uphill yarding operation was 53,369 KRW/㎥. The difference in cost resulted from the difference in the number of yarding stems (stems/cycle). Furthermore, the results of the multiple linear regression equation developed for predicting the yarding operation times showed that productivity was significantly affected by working conditions such as yarding distance (m), the number of stems per cycle (stems/cycle), and the terrain slope (%) in the uphill and downhill yarding operations. Further research is required for developing an accurate prediction model equation according to a yarding direction.

• Korean Journal of Agricultural Science
• /
• v.49 no.4
• /
• pp.677-696
• /
• 2022

Development of radish collectors may enhance radish production and promote upland crop mechanization in the Republic of Korea. Theoretical analysis of power is crucial to ensure the optimum design of agricultural machinery. The aim of the present study is to analyze theoretically the power requirement of a tractor-mounted radish collector under development and to propose design guidelines. The important components of the radish collector were belt-type conveyors, three hydraulic motors, and a direct current (DC) winch motor to operate the total radish collecting process. Theoretical equations were used to calculate the hydraulic motor's power, winch motor power, and draft power at loaded and unloaded conditions. A variety of tractors (44 - 74 kW) and different soil characteristics (hard, firm, tilted, and sandy) were considered to investigate the appropriate drawbar power. Variations of the power requirement of the tractor-mounted radish collector were observed due to modifications of the design parameters. The required hydraulic power of the stem cutting conveyor, stem cutting blade, and transfer conveyor of the radish collector were 0.23 and 0.24, 0.18 and 0.19, and 0.19 and 0.22 kW under unloaded and loaded conditions, respectively. The maximum draft power was calculated as 0.89, 1.07, 1.25, and 1.61 kW at a 30° tilted angle for hard, firm, tilted, and sandy soil, respectively. The calculation showed 2.07 kW DC power was required for unfolding or folding the stem-cutting conveyor. A maximum power of 4.78 kW was prescribed for conducting the whole process of the tractor-mounted radish collector. The analysis of power introduced in this study will be helpful to select the appropriate design parameters for the successful development of a tractor-mounted radish collector.

• Korean Journal of Agricultural Science
• /
• v.49 no.2
• /
• pp.269-284
• /
• 2022

The development of radish collectors has the potential to increase radish yields while decreasing the time and dependence on human labor in a variety of field activities. Stress and fatigue analyses are essential to ensure the optimal design and machine life of any agricultural machinery. The objectives of this research were to analyze the stress and fatigue of major components of a tractor-mounted radish collector under dynamic load conditions in an effort to increase the design dependability and dimensions of the materials. An experiment was conducted to measure the shaft torque of stem-cutting and transferring conveyor motors using rotary torque sensors at different tractor ground speeds with and without a load. The Smith-Watson-Topper mean stress equation and the rain-flow counting technique were utilized to determine the required shear stress with the distribution of the fatigue life cycle. The severity of the operation was assessed using Miner's theory. All running conditions produced more than 10⁷ of high cycle fatigue strength. Furthermore, the highest severity levels for motor shafts used for stem cutting and transferring and for transportation joints and cutting blades were 2.20, 4.24, 2.07, and 1.07, and 1.97, 3.81, 1.73, and 1.07, respectively, with and without a load condition, except for 5.24 for a winch motor shaft under a load. The stress and fatigue analysis presented in this study can aid in the selection of the most appropriate design parameters and material sizes for the successful construction of a tractor-mounted radish collector, which is currently under development.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.6 no.1
• /
• pp.85-97
• /
• 2003

This study was aimed at suggest a proper logging method of mountain forest using geographic information system(GIS) based on digital terrain model(DTM) in the National Forest at Mt. Kumsan in Namhae-gun, Gyungsangnam-do, which has about 2,948 ha in area. The areal percentage of 201 to 250m in the elevation was about 15.5%, elevation of 251 to 300m was 14.5%, and 78.75% for higher than 400m. The accumulated areal percentage of below 30% in the gradient was 17.2%, and 81.0% for steeper than 60%. The area for tractor skidding was 17.2%(511.7ha), the area for tractor attached winch skidding was 63.8%(1,896.3ha) and 18.4%(545.5ha) for cable yarding. It is important to choose the proper logging machines for timber harvesting. In general, the selection of logging operation system was affected several major environmental factors like as terrain conditions(slope gradient, slope length) and stand factors. The rate of middle slope gradients in terrain conditions showed higher than that of steep slope gradients in this area. Therefore, it considered that the logging operation system in this area could apply to tractor+winch operating machine according to terrain conditions.

• Journal of Korean Society of Forest Science
• /
• v.97 no.1
• /
• pp.61-70
• /
• 2008

This study was conducted to develop a mobile tower-yarder with tractor for agriculture and forestry that is the efficient yarder in steep terrains, thinning operation and small scale logging operation. It was designed and manufactured that the power source of tower-yarder is equiped three hydraulic pump connected to PTO of tractor, and three hydraulic pump is used to operate the four motor for drum, the cylinder for clutch of interlocker, the cylinder for tower expanding and the out-rigger cylinder. It was to adopt the running skyline system and the inter-lock function, and to equip the double capstan drum, the storage drum and the clutch for interlock in the development of tower-yarder. It was to develop the tower-yarder which the winch torque of double-capstan drum, the traction force of double-capstan drum, the number of rotation of double-capstan drum and the line speed is $191kg{\cdot}m$, 1,910 kgf, 220.5 rpm and 138.5 m/min, respectively. And it was known that the optimum flange diameter of the main and haulback storage drum is about 360 mm and about 460 mm in order to storage the main line length of 250m and the haulback line length of 450 m. The carriage was made to adopt the running skyline system and to equip the lock function in order to the convenience of chocking and the fall down preventing of tree. It was provided to develop the wire remote controller for the inter-lock function, the convenience of control and the efficiency of yarding. In development process, this tower-yarder was attached the 3-point linkage hitch equipment and the tire wheel for the traction and moving of tower-yarder. Also, it was equipped that the out-rigger and the guy line in order to raise the safety and efficiency of yarding of tower-yarder.

• Journal of Korean Society of Forest Science
• /
• v.103 no.1
• /
• pp.87-97
• /
• 2014

This study was conducted to provide field-based harvesting study information which can be used to select an optimal cable system for certain work conditions on steep grounds (> $20^{\circ}$ ground slope) in Korea. To accomplish this study objectives, we evaluated three cable yarding systems (RME-300T tower-yarder, Chuncheon tower-yarder, FARMI tractor winch) working in typical work conditions for their yarding productivity and operational efficiency. Those yarders are commonly used for removing logs or trees on steep grounds in Korea. Under the same work conditions (average DBH of tree to be cut, 20 cm; yarding distance, 60 m; lateral yarding distance, 10 m; and machine utilization rate, 70%), the average productivities were $33.04m^3$/day, $38.47m^3$/day, and $14.17m^3$/day for RME-300T, Chuncheon tower-yarder, and FARMI, respectively. Our standardized cost comparison study also showed that the yarding cost was highest at $37,835won/m^3$ with FARMI, followed by RME-300T at $25,105won/m^3$ for the same work conditions. We found the lowest yarding cost with the Chuncheon tower-yarder at $20,520won/m^3$ which was resulted primarily from high yarding productivity at the yarding distance (60 m). Our analysis suggested that a small machine such as FARMI could be a low-cost yarding machine option for a cable yarding job with a short yarding distance (40 m or less). The Chuncheon tower-yarder is well suited for a mid-range yarding distance job in Korea, ranged between 40 to 140 m. If yarding distance were longer than 140 m, the RME-300T tower yarder appears to be most cost-effective.