• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.18 no.3
• /
• pp.363-372
• /
• 2020

Anionic radionuclides pose one of the highest risks to the long-term safety assessments of disposal repositories. Therefore, techniques to immobilize and separate such anionic radionuclides are of crucial importance from the viewpoints of safety and waste volume reduction. The main objective of this study is to design a separator with minimum pressure disturbance, based on the concept of a conventional cyclone separator. We hypothesize that the anionic radionuclides can be immobilized onto a nanomaterial-based substrate and that the particles generated in the process can flow via water. These particles are denser than water; hence, they can be trapped within the cyclone-type separator because of its design. We conducted particle tracking analysis using computational fluid dynamics (CFD) for the conventional cyclone separator and studied the effects due to the morphology of the separator. The proposed sandglass-like design of the separator shows promising results (i.e., only one out of 10,000 particles escaped to the outlet from the separation zone). To validate the design, we manufactured a laboratory-scale prototype separator and tested it for iron particles; the efficiency was ca. 99%. Furthermore, using an additional magnetic effect with the separator, we could effectively separate particles with ~100% efficiency. The proposed sandglass-like separator can thus be used for effective separation and recovery of immobilized anionic radionuclides.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.1
• /
• pp.1-5
• /
• 2020

Solar power generation systems require maximum power point tracking (MPPT) control to operate PV panels at their maximum power point (MPP). Most conventional MPPT algorithms are based on the slope-tracking concept. A typical slope-tracking method is the perturb and observe (P&O) algorithm. The P&O algorithm measures the current and voltage of a PV panel to find the operating point of the voltage at which the calculated power is maximized. However, the measurement error of the sensor causes irregularity in the calculation of the generated power and voltage control. This irregularity leads to the problem of not finding the correct MPP operating point. In this work, the power output of a PV panel based on the P&O algorithm is simulated by considering the insolation profiles from typical clear and cloudy weather conditions and the errors of current and voltage sensors. Simulation analysis suggests the optimal control period and perturbation voltage of MPPT to maximize its target efficiency under real weather conditions with sensor tolerance.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.24 no.2
• /
• pp.99-104
• /
• 2019

Solar power generation systems require maximum power point tracking (MPPT) control to acquire maximum power using inefficient and high-cost PV modules. Most conventional MPPT algorithms are based on the slope-tracking concept. The perturb and observe (P&O) algorithm is a typical slope-tracking method. The two factors that determine the MPPT performance of P&O algorithm are the MPPT control period and the magnitude of the perturbation voltage. The MPPT controller quickly moves to the new maximum power point at insolation change when the perturbation voltage is set to large, and the error of output power will be huge in the steady state even when insolation is not changing. The dynamics of the MPPT controller can be accelerated even though the perturbation voltage is set to small when the MPPT control period is set to short. However, too short MPPT control period does not improve MPPT performance but consumes the MPPT controller resources. Therefore, analyzing the performance of the MPPT controller is necessary for actual insolation conditions in real weather environment to determine the optimum MPPT control period and the magnitude of the perturbation voltage. This study proposes an optimum MPPT control period that maximizes MPPT efficiency by measuring and analyzing actual insolation profiles in typical clear and cloudy weather in central Korea.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.1003-1006
• /
• 2009

Recently, Ubiquitous computing technology is increasing necessity for object recognition and a location tracking technology to meet various applications. The location tracking technology is the fundamental to the Context-Aware of users in Ubiquitous environment and its efficiency has to be improved using IEEE 802.15.4 ZigBee used in current infra such as ubiquitous sensor network. But because the IEEE 802.15.4 ZigBee protocol has limitation to apply location tracking technology such as ToA and TDoA, Zone-based Location Tracking technology using RSSI is needed. In this paper suggests RSSI-based 802.15.4 ZigBee local positioning protocol to support a positioning tracking service in Ubiqutous environment. And Zone-based location tracking system is designed for actual the indoor location tracking service.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.47 no.6
• /
• pp.6-11
• /
• 2010

Amount of power generated from solar photovoltaic can vary according to solar flux of sunlight due to nature of solar cell panel, and an angle that the sun and the surface of cell makes brings difference in amount of power generation. Solar flux is decided by location of surface of the Earth that is classified into longitude and latitude, but on the other hand, an angle that the sung and the surface of cell makes can be changed by changing the angle of a solar power generation device at the fixed location. A method of changing the angle of a solar power generation device as a measure for improving practical power generation efficiency. and studies about a solar tracking device for this are in active. This study conducted a research on a solar tracking system for improvement of solar power generation efficiency. A solar tracking system of this study is composed of a sensor part to confirm a location of the sun with a semiconductor photosensor using the photo conductive effect, and it analyzed output signal of a sensor by using microprocessor and it produced a control signal of driving part for tracking the sun. A solar power generator (25W) was produced to analyze performance of a solar tracking system and usefulness of a solar tracking device that was designed and produced in this study was confirmed through experiments.

• 제어로봇시스템학회:학술대회논문집
• /
• 1989.10a
• /
• pp.99-104
• /
• 1989

A practical filter is suggested for ground-Dasea missile tracking in a capture guidance mode, utilizing angle-only measurements from a passive sensor and its performance is evaluated by a realistic system simulation study. Also suggested is a missile acceleration model that provides inputs to the filter. The suggested filter has a decoupled structure of independent azimuth and elevation channels with efficiency in commutation time and memory requirements.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.32 no.3
• /
• pp.90-98
• /
• 1983

The method to improve the efficiency of a slightly loaded induction motor is suggested. It is based upon the optimal efficiency slip tracking by adjusting the voltage to frequency ratio(V/f). It is adopted the converter-inverter fed induction motor drive system. All the control loops are implemented bh the Z-80 microprocessor. By this method, 10% or more improvement is achieved at a few fraction of the full load.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.8
• /
• pp.56-64
• /
• 2012

This paper proposes a novel maximum power point tracking (MPPT) control algorithm considering radiation to improve efficiency of PV system. The proposed algorithm is composed perturb and observe (PO) method and constant voltage (CV) method. PO method is simple to realize and CV method is possible to tracking MPP with low radiation. Response characteristics of proposed algorithm are compared to conventional MPPT algorithm such as PO method, IC method and CV method with radiation variation. This paper proves the validity of proposed algorithm through the analysis results.

• Proceedings of the KIEE Conference
• /
• 2005.07d
• /
• pp.2684-2686
• /
• 2005

This paper presents design of nonlinear controller based on genetic-fuzzy algorithm. Motor system that is included at a humanoid robot has many nonlinear parameters such as saturation, backlash and so on. So, it is hard to control a humanoid robot because of these nonlinearities. Also, tracking following ability is also reduced by these nonlinearities. In this paper, fuzzy PID controller is proposed for reducing efficiency by saturation. At that time, genetic algorithm is supplied at making fuzzy rule in order to make optimal fuzzy PID controller. Also, disturbance observer is used to reduce the efficiency of backlash. All these processes are verified by simulation and experiment in the real humanoid robot.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.179-185
• /
• 2005

This paper presents a novel circuit topology of a high efficiency single-phase power conditioner. This power conditioner is composed of time-sharing sinewave absolute pulse width modulated boost chopper with a bypass diode in the first power processing stage and time-sharing sinewave pulse width modulated full-bridge inverter in the second power processing stage operated by time-sharing dual mode pulse pattern control scheme. The unique operating principle of the two power processing stage with time-sharing dual mode sinewave modulation scheme is described with a design example. This paper proposes also a sinewave tracking voltage controlled soft switching PWM boost chopper with a passive auxiliary edge-resonant snubber. The new conceptual operating principle of this novel power conditioner related to new energy utilization system is presented and discussed through the experimental results.