• 대한치과보철학회지
• /
• 제35권1호
• /
• pp.221-243
• /
• 1997

The objective of this study was to characterize the mechanical properties of $Y_{2}O_{3}$-containing glass infiltrated ceramic core material, which was made by pressureless powder packing method. A pure alumina powder with a grain size of about $4{\mu}m$ was packed without pressure is silicon mold to form a bar shaped sample, and applied PVA solution as a binder. Samples were sinterd at $1350^{\circ}C$ for 1 hour. After cooling, $Y_{2}O_{3}$-containing glass($SiO_{2},\;Y_{2}O_{3},\;B_{2}O_{3},\;Al_{2}O_{3}$, ect) was infiltrated to the sinterd samples at $1300^{\circ}C$ for 2 hours and cooled. Six different proportions $Y_{2}O_{3}$ of were used to know the effect of the mismatch of the thermal expansion coefficient between alumina powder and glass. The samples were ground to $3{\times}3{\times}30$ mm size and polished with $1{\mu}m$ diamond paste. Flexural strength, fracture toughness, hardness and other physical properties were obtained, and the fractured surface was examined with SEM and EPMA. Ten samples of each group were tested and compared with In-Ceram(tm) core materials of same size made in dental laboratory. The results were as follows : 1. The flexural strengths of group 1 and 3 were significantly not different with that of In-Ceram, but other experimental groups were lower than In-Ceram. 2. The shrinkage rate of samples was 0.42% after first firing, and 0.45% after glass infiltration. Total shrinkage rate was 0.87%. 3. After first firing, porosity rate of experimental groups was 50%, compared with 22.25% of In-Ceram. After glass infiltration, porosity rate of experimental groups was 2%, and 1% in In-Ceram. 4. There was no statistical difference in hardness between two materials tested, but in fracture toughness, group 2 and 3 were higher than In-Ceram. 5. The thermal expansion coefficients of experimental groups were varied to $4.51-5.35{\times}10^{-6}/^{\circ}C$ according to glass composition, also the flexural strengths of samples were varied. 6. In a view of SEM, many microparticles about $0.5{\mu}m$ diameter and $4{\mu}m$ diameter were observed in In-Ceram. But in experimental group, the size of most particles was about $4{\mu}m$, and a little microparticles was observed. The results obtained in this study showed that the mismatch of the thermal expansion coefficients between alumina powder and infiltrated glass affect the flexural strength of alumin/glass composite. The $Y_{2}O_{3}$-containing glass infiltrated ceramic core made by powder packing method will takes less time and cost with sufficient flexural strength similar to all ceramic crown made with slip casting technique.

• 보존과학회지
• /
• 제31권1호
• /
• pp.1-11
• /
• 2015

보물 제1312호 무위사 아미타여래삼존좌상은 기존에 목조불로 알려졌으나 2009년에 실시한 정밀안전진단을 통해 본존불인 아미타여래좌상은 흙으로 조성된 소조불로 밝혀졌다. 그런데 아미타여래좌상의 소조층은 손상이 심각하여 보수가 불가피하였고, 이에 보수재료로서 보다 안전하고 적합한 충전제에 대한 연구를 진행하였다. 본 연구는 무위사 아미타여래좌상의 소조층 보수에 가장 적합한 충전제를 제작하기 위한 실험으로 다양한 비율로 배합한 조합토 샘플을 제작한 후 건조 시 표면의 경화상태, 균열 및 색상변화, 수축률 결과를 측정하였다. 충전제 제작에 사용된 조합토 재료는 황토와 세사, 면 솜을 적용하였으며 6가지의 배합비율로 조합토 시료를 만들고 여기에 찹쌀풀, 도박풀, 아교로 만든 12가지 농도의 접착제를 혼합하여 총72가지 조건의 시료를 제작하여 비교분석 하였다. 실험결과 조합토는 황토와 세사의 질량비에 대하여 2.5%의 면 솜을 함유하고, 황토와 세사의 비율이 15:1일 때 수축률이 가장 낮은 것으로 판명되었으며, 천연접착제 중 색상의 변화가 적고, 물성변화량과 수축률이 가장 낮은 아교가 사용 가능한 접착제로 판단되었다. 즉, 조합토(황토:세사=15:1)와 아교15ml 첨가 시 가장 낮은 수축률을 나타내어 무위사 아미타여래좌상 보존처리 시소조층의 충전제로 가장 적합한 것으로 판명되었다.

• Computers and Concrete
• /
• 제14권5호
• /
• pp.599-612
• /
• 2014

This paper presents the effects of the construction stages using time dependent material properties on the structural behaviour of concrete arch dams. For this purpose, a double curvature Type-5 arch dam suggested in "Arch Dams" symposium in England in 1968 is selected as a numerical example. Finite element models of Type-5 arch dam are modelled using SAP2000 program. Geometric nonlinearity is taken into consideration in the construction stage analysis using P-Delta plus large displacement criterion. In addition, the time dependent material strength variations and geometric variations are included in the analysis. Elasticity modulus, creep and shrinkage are computed for different stages of the construction process. In the construction stage analyses, a total of 64 construction stages are included. Each stage has generally $6000m^3$ concrete volume. Total duration is taken into account as 1280 days. Maximum total step and maximum iteration for each step are selected as 200 and 50, respectively. The structural behaviour of the arch dam at different construction stages has been examined. Two different finite element analyses cases are performed. In the first case, construction stages using time dependent material properties are considered. In the second case, only linear static analysis (not considered construction stages) is taken into account. Variation of the displacements and stresses are obtained from the both analyses. It is highlighted that construction stage analysis using time dependent material strength variations and geometric variations has an important effect on the structural behaviour of arch dams. The maximum longitudinal, transverse and vertical displacements obtained from construction stages and static analyses are 1.35 mm and 0 mm; -8.44 and 6.68 mm; -4.00 and -9.90 mm, respectively. In addition, vertical displacements increase from the base to crest of the dam for both analyses. The maximum S11, S22 and S33 stresses are obtained as 1.60MPa and 2.84MPa; 1.39MPa and 2.43MPa; 0.60MPa and 0.50MPa, respectively. The differences between maximum longitudinal, transverse, and vertical stresses obtained from construction stage and static analyses are 78%, 75%, and %17, respectively. On the other hand, there is averagely 12% difference between minimum stresses for all three directions.

• Food Science and Biotechnology
• /
• 제17권2호
• /
• pp.319-323
• /
• 2008

Mutant rice cv. Goami2 (G2) and Baegjinjoo (BJJ) derived from a high-quality japonica rice cv. Ilpumbyeo (IP) were extruded under different feed moisture (20 and 30%) and barrel temperature (90, 110, and $130^{\circ}C$). Increasing feed moisture at fixed barrel temperature increased extrudate density (ED) in IP and BJJ. Whereas, G2 showed a varied ED depending on extrusion conditions; increasing barrel temperature decreased the ED of G2 extrudate with low feed moisture, but increased with high moisture. Results indicated a positive barrcl temperature effect on volume expansion in IP and G2, but a negative effect on 811, probably due to shrinkage of expanded products containing low-amylose contents. A significant increase of water absorption was found in G2 and BJJ extruded flour, while an increase of water solubility in those from IP. Non-digestible carbohydrates measured by total dietary fiber (TDF) indicated that extrusion increased slightly TDF in IP and BJJ extrudates, but decreased in G2 products, which might be variety-dependent.

• Asian Pacific Journal of Cancer Prevention
• /
• 제13권1호
• /
• pp.319-323
• /
• 2012

Objective: To explore the feasibility of shrinking field technique after 40 Gy radiation through 18F-FDG PET/CT during treatment for patients with stage III non-small cell lung cancer (NSCLC). Methods: In 66 consecutive patients with local-advanced NSCLC, 18F-FDG PET/CT scanning was performed prior to treatment and repeated after 40 Gy. Conventionally fractionated IMRT or CRT plans to a median total dose of 66Gy (range, 60-78Gy) were generated. The target volumes were delineated in composite images of CT and PET. Plan 1 was designed for 40 Gy to the initial planning target volume (PTV) with a subsequent 20-28 Gy-boost to the shrunken PTV. Plan 2 was delivering the same dose to the initial PTV without shrinking field. Accumulated doses of normal tissues were calculated using deformable image registration during the treatment course. Results: The median GTV and PTV reduction were 35% and 30% after 40 Gy treatment. Target volume reduction was correlated with chemotherapy and sex. In plan 2, delivering the same dose to the initial PTV could have only been achieved in 10 (15.2%) patients. Significant differences (p<0.05) were observed regarding doses to the lung, spinal cord, esophagus and heart. Conclusions: Radiotherapy adaptive to tumor shrinkage determined by repeated 18F-FDG PET/CT after 40 Gy during treatment course might be feasible to spare more normal tissues, and has the potential to allow dose escalation and increased local control.

• 한국지반환경공학회 논문집
• /
• 제10권4호
• /
• pp.33-40
• /
• 2009

성토 시공시, 경제적인 시공을 위해 절 성토량의 균형은 중요하게 고려되어야 할 사항이다. 그러나 실제 완성기면까지 성토시 성토체 자체의 압축침하와 연약지반 성토시 발생하는 제체하부 원지반의 압밀침하, 암 버럭 사이의 간극 메움에 의한 침하와 강우와 유출시 발생하는 토량 손실에 의한 성토량의 부족분이 발생하고 있다. 성토량의 부족분에 대한 지침은 도로공사 시방서에 토량환산계수를 통해 설계하도록 되어 있지만 성토체 자체의 압축침하에 의한 부족분은 고려되고 있지 않다. 따라서 본 연구에서는 이세전(伊勢田)(1972)와 석정(石井)(1976)가 제안하고 있는 성토체의 제체압축침하량 산정기법을 적용하여 국내 여러 현장의 성토체를 대상으로 발생가능한 압축침하량을 산정하였다. 본 연구결과 성토고 및 성토재의 종류에 따라 성토고의 약 3~10%내외의 전침하량이 발생하는 것으로 나타났다. 그러므로 실제 설계시 성토재의 특성 및 성토고를 고려한 성토체의 즉시침하 및 크리프 침하를 반영한 설계가 필요할 것으로 판단된다.

• 구강회복응용과학지
• /
• 제23권3호
• /
• pp.239-248
• /
• 2007

The accuracy and dimensional stability of rubber impression materials are very important for the fitness of the final restoration. The purpose of this investigation was to evaluate the effects of the storage time and pouring frequency of the additional silicone materials on dimensional stability. Total 30 impressions were made of tooth prepared single crown. The dies had 1 buccolingual, 1 mesiodistal and 1 occlusogingival lines. Two additional silicone materials(examixfine, aquasil) were included. 15 specimens were made of each impression material and poured by type IV stone over times(1hour, 24hours, 72hours) after mixing. 5 impressions poured after 1 hour were used for second pouring after 24hours and third pouring after 72hours. The same examiner measured each specimen 3 times after lazer scanning. All statistical tests were performed with the level of significance set at 0.05. The results indicated that significant difference at any measuring point of stone dies except the buccolingual and mesiodistal lines of the specimen made at 1hour after mixing with examixfine when measurements at 1hour, 24hours and 72hours were campared. There were significant difference between two impression materials and at every measuring point of stone dies made at second and third pouring. The length of measuring point increased significantly as time passed by and increase of the pouring frequency. However, this results are clinically acceptable except the dies of the third pouring. Under the conditions of this study, the shrinkage rate of the additional silicone rubber impression materials significantly increased as time passed by and increase of the pouring frequency.

• Advances in pediatric surgery
• /
• 제2권2호
• /
• pp.102-109
• /
• 1996

Pediatric surgeons are familiar with the posterior sagittal approach to the rectum at sacrococcygeal area and well oriented with the anatomy because of the Penal procedure for imperforate anus. The author utilized the posterior vertical elliptical incisions in 12 cases of sacrococcygeal teratoma since 1987. For presacral tumor(type IV)$^2$, the incision was exactly same as the posterior sagittal procedure for imperforate anus. But the out-growing(type I) or dumbbell-shaped(type II & III) tumors, a vertical elliptical incision was required. For the laterally deviated tumors, a vertical and half-chevron incision was utilized in one case, but an unbalanced vertical elliptical incision was acceptable for the remaining two cases, with shrinkage of the overlying skin. In dumbbell-shaped tumors(type II & III), the narrow waist of the tumor was at the level of the levator muscle, which formed a muscle-belt on the tumor waist. A careful dissection to save the muscle-belt seemed to be the most important point during this procedure, utilizing the nerve-stimulator. After complete removal of the tumor and the coccyx, the levator muscles and the skin were closed in vertical fashion along the midline. For the caudally extending tumors in 3 cases, the muscle complex was divided in midline. Nothing by mouth and total parenteral nutrition was maintained for 1 week and then laxatives were given for 2 weeks in order to give the sphincters rest. Operative scars were acceptable resembling natural vertical midline folds, and the sphincter function was continent in all cases. In conclusion, vertical elliptical incision in sacrococcygeal teratoma is recommended because of the acceptable scar, functional restoration, and because it is a familiar procedure particularly for the pediatric surgeons who are accustomed performing posterior sagittal approach for imperforate anus.

• 한국축산식품학회지
• /
• 제40권3호
• /
• pp.338-349
• /
• 2020

The effects of organic Zn-L-selenomethionine (Zn-L-SeMet) at 0.3 ppm on carcass composition, meat characteristics, fatty acid composition, glutathione peroxidase activity, and ribonucleotide content were compared against the commercial inorganic sodium selenite (Na-Se) and the combination of the two, in commercial broilers. A total of 540 one day-old chicks were assigned at random to 3 dietary treatments : i) commercial inorganic selenium as control or T1, ii) a 1:1 ratio of inorganic and organic selenium as T2, and iii) organic selenium as T3. Carcass composition, meat characteristics, cholesterol content, fatty acid composition, and ribonucleotide content were generally unaffected by treatments. However, discrepancy were significantly observed in glutathione peroxidase activity (GSH-Px) and water holding capacity, with organic selenium showing higher glutathione peroxidase activity (p<0.01) and lower shrinkage loss (p<0.05), respectively. These findings could be explained by the contribution of organic selenium in bioavailability of GSH-Px. However, having conducted in a commercial close house system with sufficient amount of nutritional supplementation, the present study demonstrated little or no effects of organic Zn-L-SeMet on meat characteristics, fatty acid composition, and ribonucleotide content (flavor characteristic) in broiler chickens.

• 대한치과기공학회지
• /
• 제37권1호
• /
• pp.9-15
• /
• 2015

Purpose: The purpose of this study was to compare the accuracy of the maxillary three-unit fixed dental prosthesis (FDPs) made using two CAD/CAM milling machines : DCM Group(Dentaim CAD/CAM milling machine), WCM Group(Wieland CAD/CAM milling machine). Methods: Each of 10 duplicate models was scanned by blue light scanner(Identica, Medit, Korea), and the three-unit FDPs (STL file) was designed using DelcamCAD. A total of 20 three-unit FDPs was fabricated, comprising 2 groups of 10 specimens each (shrinkage ratio is 1:1). The first three-unit FDPs STL file was used as a CAD reference model (CRM). Obtained STL files by scanning the inner surface of three-unit FDPs were convened into the point clouds-ASC II files. Discrepancies between the point clouds and CRM were measured by superimposition software. Statistical methods to analyze the data were used non-parametric method. The mean (SD) values were compared by a Mann-Whitney U-test. Type one error rate was set at 0.05. Results: WCM group had small discrepancies with $2.17{\mu}m$ of mean value compared to $4.44{\mu}m$ in DCM group. The accuracy values between the two groups showed a sratistically significant difference (Table 2, p<.05). Conclusion: The accuracy of the three-unit fixed dental prosthesis(FDPs) made of two CAD/CAM milling machines were statistically different. Accuracy with which the prosthesis made of WCM group was superior.