• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.4
• /
• pp.422-429
• /
• 1988

The photoconductive multilayer of Se-As(hole blocking layer)/Se-As-Te (photoconductive layer) /Se-As (layer for supporiting hole transport)/Se-As(layer or controlling total capacitance)/Sb2S3(electron blocking layer) was fabricated and its electrical and optical properties were investigated. The photoconductive multilayer is made of evaporated a-Se as the base material, doped with As and Te to prevent the crystallization of a-Se and to enhance red sensitivity, respectively. The multilayer with good image reproducibility has the following deposition condition. The first layer has the thickness of 250\ulcornerat the deposition rate of 250\ulcornersec. The second layer has the thickness of 800\ulcornerat the deposition rate of 250\ulcornersec. The third layer has the thickness of 125\ulcornerat the deposition rate of 250\ulcornersec. The fourth layer has the thickness of 1700\ulcornerunder the Ar gas ambient of 50x10**-3torr. The image pick-up tube, employing this multilayer demonstrates the following characteristics. The photosensitivity is 0.8, the resolution limit is above 300TV line, and the decay lag is about 7%. And spectral response convers the whole visible range. Therfore the application to color TV camera is expected.

• Proceedings of the Korean Environmental Health Society Conference
• /
• 2003.06a
• /
• pp.76-85
• /
• 2003

Mass and elemental dry deposition fluxes and ambient particle size distributions were measured using dry deposition plates and a cascade impactor, from March to November 1998 in Seoul, Korea. During the spring sampling period several yellow sand events characterized by long range transport from China and Mongolia impacted the area. During these events the mass fluxes were statistically the same as during springtime non-yellow-sand events. However, most elemental fluxes were higher. In general, the flux ratios of both crustal (Al, Ca, Mn) and anthropogenic elements (Ni, Pb) to total mass measured during the daytime yellow-sand events were substantially higher than those measured in spring daytime during non-yellow-sand time periods. During all seasons the average measured daytime fluxes were about two times higher than at nighttime. The flux of primarily anthropogenic metals (Cu, Ni, Pb, Zn) and Mn was on average one to two orders of magnitude lower than the flux of the crustal metals Al and Ca. As is typically found two modes, fine (0.1∼l.0 $\mu\textrm{m}$) and coarse (1.0∼10.0 $\mu\textrm{m}$) were present in the measured size distributions (<10 $\mu\textrm{m}$). The particles in the coarse mode constitute a major portion of the measured mass size distribution during the yellow-sand events possibly due to the long-range transport of those particles from China.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.8 s.179
• /
• pp.1958-1967
• /
• 2000

Rapid Prototyping( RP ) has been increasingly applied in the process of design and development of new products. RP can shrink the time and expense required to bring a new product from initial concept to production. However, the necessity of using RP for short-run manufacturing is continuously driving a development of a cost-effective technique that will produce completely-finished quality parts in a very short time. To meet these demands, the improvements in production speed, accuracy materials, and cost are crucial. Thus, a new hybrid-RP system performing both deposition and machining in a station is proposed in this paper. It incorporates both material deposition in layers and material removal from the outer surface of the layer to produce the required surface finish. The new hybrid-RP system can dramatically reduce the total build time and fabricate largo-sized and freeform objects because it uses very thick layers, i.e.

• The Journal of the Petrological Society of Korea
• /
• v.22 no.4
• /
• pp.273-289
• /
• 2013

Fallout ash is a notorious hazard that can have a variety of damages on agriculture and infrastructure and, most notably to aviation and human health. This study discusses the design of a conceptual model to aid in modeling the dispersal and deposition of ash from Mt. Baekdu volcano. It includes a discussion of assumptions and boundary conditions of the model as well as a detailed diagram of the conceptual model, complete with input parameters, units and equations. The two main processes contained within the model are the dispersal and deposition of ash, the outputs obtained from running the model, if designed, would be the total amount of fine ash contained in the eruption column, distance travelled by ash and ash thickness at surface.

• Journal of Korean Society for Atmospheric Environment
• /
• v.11 no.4
• /
• pp.351-359
• /
• 1995

In order to investigate geochemical behaviors of artificial radionuclide($^{137}$ Cs), the fallout deposition of arificial radioisotope($^{137}$ Cs) was measured from May to October in 1994 at the Korea Ocean Research & Development Institute(KORDI), Ansan, Kyunggido, Korea. And to study radioisotopic behavior and cumulative action in soil, soil samples were collected from Kwang-Leung Forest, Kyunggidom and artificial radioisotope ($^{137}$ Cs) and natural radioisotope($^{210}$ Pb) were identified. The amount of $^{137}$ Cs in atmosphere collected by wet deposition process in May was found to be 4.95 to 11.96mBq m$^{-2}$ whereas the amounts of $^{137}$ Cs by dry deposition process in May and October were found to be 4.0mBq g$^{-1}$ and 3.0mBq g$^{-1}$ , respectively. The amount of $^{137}$ Cs accumulated in soil was measured to be 311mBq cm$^{-2}$ , which contained 83% of the total inputs from atmospheric fallout (374 mBq cm$^{-2}$ ) since 1960s. In addition, the accumulation rate and the annual flux of $^{210}$ Pb into soils were 0.32cm yr$^{-1}$ and 34 mBq cm$^{-2}$ yr$^{-1}$ , respectively. Conclusively, it was found that arificial radioisotopes were mainly from the stratosphere and soil resupension of continental China through the troposphere.

• Korean Journal of Materials Research
• /
• v.12 no.5
• /
• pp.363-368
• /
• 2002

we proposed the use of $Si_2H_ 6/H_2$ chemistry for selective silicon epitaxy growth by low-pressure chemical vapor deposition(LPCVD) in the temperature range $600~710^{\circ}C$ under an ultraclean environment. As a result of ultraclean processing, an incubation period of Si deposition only on $SiO_2$ was found, and low temperature epitaxy selective deposition on Si was achieved without addition of HCI. Total gas flow rate and deposition pressure were 16.6sccm and 3.5mtorr, respectively. In this condition, we selectively obtained high-quality epitaxial Si layers of the 350~1050$\AA$ thickness. In older to extend the selectivity, we kept high pressure $H_2$ environment without $Si_2H_6$ gas for few minutes after first incubation period and then we conformed the existence of second incubation period.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.21 no.1
• /
• pp.165-173
• /
• 2023

Various linear system solvers with multi-physics analysis schemes are compared focusing on the near-field region considering thermal-hydraulic-chemical (THC) coupled multi-physics phenomena. APro, developed at KAERI for total system performance assessment (TSPA), performs a finite element analysis with COMSOL, for which the various combinations of linear system solvers and multi-physics analysis schemes should to be compared. The KBS-3 type disposal system proposed by Sweden is set as the target system and the near-field region, which accounts for most of the computational burden is considered. For comparison of numerical analysis methods, the computing time and memory requirement are the main concerns and thus the simulation time is set up to one year. With a single deposition hole problem, PARDISO and GMRES-SSOR are selected as representative direct and iterative solvers respectively. The performance of representative linear system solvers is then examined through a problem with an increasing number of deposition holes and the GMRES-SSOR solver with a segregated scheme shows the best performance with respect to the computing time and memory requirement. The results of the comparative analysis are expected to provide a good guideline to choose better numerical analysis methods for TSPA.

• Journal of Korea Water Resources Association
• /
• v.37 no.11
• /
• pp.959-967
• /
• 2004

The concentrations and loads of total nitrogen (TN), total phosphorus (TP), and chemical oxygen demand (COD) in wet deposition were investigated at Chungbuk National University in Cheongju, Chungbuk. Event based precipitation samples were collected during 1998 to 2003. The precipitation-weighted mean concentrations of pollutants were 0.60 mg/L for TN, 0.014 mg/L for TP, and 4.8 mg/L for COD, which were smaller than its arithmetic mean concentrations by 26% for TN, 18% for TP, and 14% for COD. The concentrations of TN, TP, and COD significantly decreased with precipitation. Mean concentrations of pollutants in spring (March-May) were higher than in other seasons likely due to dust caused by wind erosion and sand-dust storms, pollen etc. Significant relationships were determined between TN and TP, and TN and COD. Annual loads of wet deposition averaged 7.9 kg/ha$\cdot$yr for TN, 0.19 kg/ha$\cdot$yr for TP, and 63.9 kg/ha$\cdot$yr for COD, which are almost identical to the values of TN and TP but slightly higher than COD value reported in Japan.

• Journal of Radiation Protection and Research
• /
• v.23 no.4
• /
• pp.243-249
• /
• 1998

The methodology for justification and optimization of the countermeasures related with contamination management of milk was designed based on the cost and benefit analysis. The application results were discussed for the deposition on August 15, when pasture is fully developed in Korean agricultural conditions. A dynamic food chain model DYNACON was used to estimate the time-dependent radioactivity of milk after the deposition. The considered countermeasures are (1) the ban of milk consumption (2) the substitution of clean fodder, which are effective in reducing the ingestion dose as well as simple and easy to carry out in the first year after the deposition. The total costs of the countermeasures were quantitatively estimated in terms of cost equivalent of doses and monetary costs. It is obvious that a fast reaction after the deposition is an important factor in cost effectiveness of the countermeasures. In most cases, the substitution of clean fodder was more effective countermeasure than the ban of consumption. A fast reaction after the deposition made longer justifiable/optimal duration of the countermeasure.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.34 no.2
• /
• pp.153-159
• /
• 2016

Rivers refer to either natural or artificial structures whose primary functions are flood control and water conservation. Due to recent localized torrential downpours led by climate change, large amounts of eroded soil have been carried away, forming deposits downstream, which in turn degrades the capacity to fulfill these functions. To manage rivers more effectively, we need data on riverbed erosion and deposition. However, environmental factors make it challenging to take measurements in rivers, and data errors tend to prevent researchers from grasping the current state of erosions and deposits. In this context, the aim of the present study is to provide basic data required for river management. To this end, the author made annual measurements with a Real-time Kinematic-Global Positioning System (RTK-GPS) and a total station in Pats Cabin Canyon, Oregon, United States, and also prepared thematic maps of erosion and deposition thickness as well as water depth profiles based on a GIS spatial analysis. Furthermore, the author statistically analyzed the accuracy of three dimensional (3D) measurement points and only used the data that falls within two standard deviations (i.e. ±2σ). In addition, the author determined a threshold for a DEM of Difference (DoD) by installing measurement points in the rivers and taking measurements, and then estimated erosion and deposition thickness within a confidence interval of ±0.1m. Based on the results, the author established reliable data on river depth profiles and thematic maps of erosion and deposition thickness using pre-determined work flows. It is anticipated that the riverbed data can be utilized for effective river management.