• 대한기계학회논문집A
• /
• 제35권11호
• /
• pp.1461-1469
• /
• 2011

본 논문은 3 차원 유한요소해석 기법을 이용하여 토오크 시험을 위한 표준시험시편의 각도 및 동심 오열이 시편의 응력과 변형률 변화에 미치는 영향을 분석하였다. 해석 결과의 정량적 비교를 위해 각, 동심 및 복합 축 오열에 대한 평균 굽힘 변형률을 적용하였으며, 시편 형상에 따른 축 오열 영향을 확인하기 위해 환봉형 시편과 튜브형 시편에 대해 각각 유한요소해석을 실시하였다. 해석결과로부터 얻어진 변형률과 응력의 변화로 축 오열의 종류와 방향을 예측하는 일반적인 기준을 제시하였으며, 초기 항복조건을 적용하여 축 오열이 토오크 시편의 초기 항복 모멘트에 미치는 영향을 분석하였다.

• Journal of Korean Dental Science
• /
• 제4권2호
• /
• pp.46-51
• /
• 2011

Purpose: For aesthetic reasons, composite resin brackets are widely used. However, related studies are rare. This pilot study sought to compare the stress distributions in two commercially available composite resin brackets with metal slot. Materials and Methods: Two commercially available resin brackets -- full-metal slot resin bracket (fSRB) and partial-metal slot resin bracket (pSRB) with straight wire appliance dimension of $0.022{\times}0.028$ in -- were selected. In each bracket, 3-dimensional finite element models were constructed, and stress level was evaluated using finite element analysis. By loading the tipping force and torsion moment, which are similar to those applied by the stainless steel rectangular wire ($0.019{\times}0.025$ -in), stress distributions were calculated, and von Mises stress values were obtained. Results: In pSRB and fSRB, the stress value of the torque moment was much higher than that of the tipping force. The pSRB showed higher stress value than fSRB in both tipping force and torque moment because of the difference in size and configuration of the metal frame inserted into the slot. More stress was also found to be concentrated on the slot area than the wing area in fSRB. Conclusion: The slot form of fSRB was found to be more resistant to the stress of tipping and torque than the slot form of pSRB. In addition, the slot areas -- rather than the wing areas -- of the bracket showed breakage susceptibility. Therefore, resistance to the torque moment on the slot area should be considered in bracket design.

• Structural Engineering and Mechanics
• /
• 제44권2호
• /
• pp.197-217
• /
• 2012

Detailed analysis of internal forces of exterior beam-column joints of RC frames under seismic action is reported in this paper. A formula is derived for calculating the average joint shear from the column shears, and a formula is proposed to estimate torque in eccentric joints induced by seismic action. Average joint shear stress and strain are defined consistently for exterior joints, which can be used to establish joint shear constitutive relationship. Numerical results of shear, bending moment and torque in joints induced by seismic action are presented for a pair of concentric and eccentric exterior connections extracted from a seismically designed RC frame, and two sections located at the levels of beam bottom and top reinforcement, respectively, are identified as the critical joint sections for evaluating seismic joint behavior. A simplified analysis of the effects of joint shear and torque on the flexural strengths of the critical joint sections is made for the two connections extracted from the frame, and the results indicate that joint shear and torque induced by a strong earthquake may lead to "joint-hinging" mechanism of seismically designed RC frames.

• International Journal of Aeronautical and Space Sciences
• /
• 제10권2호
• /
• pp.95-105
• /
• 2009

The flow fields around the HARTII rotor were numerically investigated using a viscous flow solver on adaptive unstructured meshes. An overset mesh and a deforming mesh technique were used to handle the blade motion including blade deflection, which was obtain from the HARTII experimental data. A solution-adaptive mesh refinement technique was also used to capture the rotor wake effectively. Comparison of the sectional normal force and pitching moment at 87% radial station between the two cases, with and without the blade deflection, showed that the blade loading is significantly affected by blade torsion. It was found that as the mesh was refined, the strength of tip vortex is better preserved, and the magnitude of high frequency blade loading, caused by blade-vortex interaction (BVI), is further magnified. It was also found that a proper time step size, which corresponds to the cell size, should be used to predict unsteady solutions accurately. In general, the numerical results in terms of the unsteady blade loading and the rotor wake show good agreement with the experimental data.

• Steel and Composite Structures
• /
• 제13권1호
• /
• pp.71-89
• /
• 2012

The paper investigates beam lateral buckling stability according to linear and non-linear models. Closed form solutions for single-symmetric cross sections are first derived according to a non-linear model considering flexural-torsional coupling and pre-buckling deformation effects. The closed form solutions are compared to a beam finite element developed in large torsion. Effects of pre-buckling deflection and gradient moment on beam stability are not well known in the literature. The strength of singly symmetric I-beams under gradient moments is particularly investigated. Beams with T and I cross-sections are considered in the study. It is concluded that pre-buckling deflections effects are important for I-section with large flanges and analytical solutions are possible. For beams with T-sections, lateral buckling resistance depends not only on pre-buckling deflection but also on cross section shape, load distribution and buckling modes. Effects of pre-buckling deflections are important only when the largest flange is under compressive stresses and positive gradient moments. For negative gradient moments, all available solutions fail and overestimate the beam strength. Numerical solutions are more powerful. Other load cases are investigated as the stability of continuous beams. Under arbitrary loads, all available solutions fail, and recourse to finite element simulation is more efficient.

• 한국항행학회논문지
• /
• 제16권2호
• /
• pp.367-374
• /
• 2012

박판 폐단면을 갖는 프레임과 같은 보가 warping 조건하에서 동적 거동 특성이 어떠한가를 시뮬레이션과 시험을 통하여 제시하였다. 비틀림 모멘트를 받는 보는 단면은 비틀림 뿐만 아니라 warping에 의해서 변형을 일으키게 된다. 어떤 박판 단면을 갖는 보에서는 warping이 매우 커서 축방향과 전단방향 응력을 발생하고 보의 비틀림에 저항이 크게 된다. 이 논문에서는 유한요소에서 warping restraint factor가 보의 변형 거동과 동적 모드에 미치는 영향을 살펴본다. 유한 보 요소와 박판 요소 모델을 사용하여 정적변형과 고유주파수 및 모드해석을 시뮬레이션하며 이 결과를 시험 결과와 비교한다.

• 한국정밀공학회지
• /
• 제23권8호
• /
• pp.154-162
• /
• 2006

By laying its drum horizontally, front-loaded washing machine mostly used in Europe that uses the head of the water to launder was appropriate for washing only small amount of laundry. However, the demands of customers are requiring front-loaded washing machine to handle big capacity laundry as well, and have faster rotation speed to increase drying ability. To meet such demands, more stress from bending and twisting are complexly loaded onto the shaft supporting the horizontal drum, causing problems in fracture strength and fatigue life. Shafting system is mainly divided into flange and shaft. Flange is located between the drum and shaft, transferring power from the shaft to drum, and acting as a supporter of the back of the drum. Shaft is connected from the flange to insert production, transferring power from the motor to drum, and mainly acting as stiffness against the horizontal weight of the shafting system. In this paper, strength analysis and experiment were executed on both the shaft and flange of front-loaded washing machine to suggest the design improvement of shafting system for big capacity, high-rotation drying. Also, verification of this evaluation was executed on fracture strength and fatigue life for studied shaft system.

• 한국산학기술학회논문지
• /
• 제10권3호
• /
• pp.500-506
• /
• 2009

본 논문은 주요 부위에 대한 정적음력 시뮬레이션을 통해 PFA 라이닝 플러그밸브 본체의 설계자를 지원하는 것을 주된 목표로 한다. CAD 작업을 통해 생성된 형상 모델을 스텝(step)파일로 변환하여 해석작업에 사용한다. 전문적인 해석경험이 없는 밸브 생산업체의 설계자가 형상 모델에 대한 인장, 굽힘, 비틀림 모멘트 등을 계산하는 과정을 이해함으로써 구조적 취약점을 사전에 파악하고, 제품에 반영하여 제품 신뢰도 및 설계효율 증대에 기여할 수 있는 기본적인 방안을 제시하고자 하였다.

• 한국공간구조학회논문집
• /
• 제20권4호
• /
• pp.93-100
• /
• 2020

In this study, structural characteristics were analyzed by combining gravity load and lateral loads such as seismic loads through static analysis of example structures, and the static characteristics of the twisted structure according to the plane rotation angle were also analyzed. Example structures were selected as regular structure, and twisted structures; 1.0, 2.0, and 3.0 degree angle of rotation per story, and static analysis was performed by the load combination case 1 and case 2. As a result the story drift ratio of the twisted-shaped structure also increased as the plane rotation angle per story increased. The eccentricity according to the load combination was the highest in the lower stories of all analysis models, and the eccentricity was found to be larger as the rotation angle decreased. The twisted-shaped structure was more responsible for the bending moment of the column than the regular structure, and the vertical member axial force of all analysis models was almost similar.

• 한국공간구조학회논문집
• /
• 제21권4호
• /
• pp.23-30
• /
• 2021

In this paper, a twisted shape structure with an elevation form favorable to the resistance of vibration caused by wind loads is selected from among the forms of high-rise buildings. The analytical model is a square, triangular, and hexagonal plane with a plane rotation angle of one degree from 0 to 3 degrees per each story. As a result of the analysis, as the twist angle increased, story drift ratio is increased. Responses with different eccentricity rates were shown by analytical models. Therefore planar shapes designed symmetrically to the horizontal axis of X and Y are considered advantageous for eccentricity and torsion deformation. In the case of the bending moment of the column, the response was amplified in the column supporting the base floor, the roof floor, the floor in which the cross-section of the vertical member changes, and the floor having the same number of nodes as the base floor. Finally, the axial force response of the column is determined to be absolutely affected by the gravity load compared to the lateral load.