• 한국기계가공학회지
• /
• 제8권2호
• /
• pp.40-45
• /
• 2009

This study is analyzed by stress contour of automotive tire at contact on road surface. Maximum equivalent stress as 61200Pa is shown on the lower mid part in case of tire contacted on road surface. As the air pressure of tire increases, maximum total deformation as 5mm is shown on the side part of tire. It can be shown that the side part of tire is unstabilized. There is no load effect on tire at its upper and lower directions. When the moment applied on the side of tire is increased 1.4 times as its value, the value of maximum principal stress is increased 1.4 times. The stress at the tire is in proportion to the moment applied on the its side. The tire tends to incline toward its side by this moment.

• Journal of Biosystems Engineering
• /
• 제26권2호
• /
• pp.123-130
• /
• 2001

The research described in this paper was aimed toward improving the understanding of the interaction of tire inflation pressure and the soil-tire interface stresses. A three-directional stress transducer was developed to measure stress distribution on undertread for a tractor tire. The transducer can directly measure three-directional stresses (normal stress, tangental stress and lateral stress and lateral stress) simultaneously and has both strong structure and high sensitivity, which is not changed by the abrasion of the detecting plate. Measurements of soil-undertread interface stresses were made at tire center on undertread on a 12.4-R24 radial tractor tire opeated at three combinations of a dynamic load (11.8kN) and three inflation pressures (59kPa, 108kPa and 157kPa). These measurements showed that as inflation pressure increased, the soil-undertread interface stresses increased. The results of three stresses comparisons were shown that the peak normal stresses were considerably higher than the tangential peak stresses and the peak lateral stresses.

• 한국정밀공학회지
• /
• 제12권3호
• /
• pp.101-109
• /
• 1995

Axisymmetric and quasi-static finite element analysis of an inflated tire rotating with constant angular velocity and contact to road has been performed. Centrifugal force effect was added to load stiffness matrix and equation of effective material properties were calculated by the Halpin-Tsai formulation. In this report, radial truck/bus tire was analyzed. It was inflated and rotated at speeds up to 140 km/h. Then, contact problem was performed to calculate stress-strain field of tire wiht flat rigid road under the load due to the self-weight of a vehicle. Significant changes of stress-strain field of tire were observed in the finite element analysis. Shear stress, strain and strain energy density were rapidly increased at the dege of #2 belt at freely rotating state. This concentrated stress and strain made belt edge sparation. Under the condition of flat riged road contact, strain energy density of #2 belt, carcass turn-up part were concentrated and bigger values than only freely rotation state. Therefore, dynamic behaivor of tire has to considered as design factors which are affected to belt edge separation and bead breakage.

• Journal of Biosystems Engineering
• /
• 제26권3호
• /
• pp.245-252
• /
• 2001

This study was carried out to investigate the effect of three factors(dynamic load, inflation pressure and multiple passes of the tire) on the contact pressure and the soil stresses under the tire. A series of soil bin experiment was conducted with a 6.00R14 radial-ply tire for sandy loam soil. Tire contact pressure at soil surface and soil stresses at 10cm and 20cm soil depth were measured for the three levels of dynamic load(1.17kN, 2.35kN and 3.53kN), for the three levels of tire inflation pressure(103.42kPa, 206.84kPa and 413.69kPa), and for five different number of passes(1, 2, 3, 4 and 5 pass). The following results were drawn from this study 1) As dynamic load, inflation pressure and number of passes of the tire increased, tire contact pressure at soil surface and soil stresses at 10cm and 20cm soil depth increased accordingly. Thus increased in dynamic load, inflation pressure and number of passes of the tire would increase soil compaction. 2) The effect of three different factors, or dynamic load, inflation pressure and number of passes of the tire, decreased as the soil depth increase. Consequently, it was found that the soil compaction at a shallow depth in soil is larger than that at deep place in soil. 3) The increase of dynamic load and number of passes increased soil stress exponentially, but the increase of inflation pressure increased soil stress linearly. The effect of tire inflation pressure on soil stress was relatively less than that of the dynamic load. Therefore, it was concluded that dynamic load is more important factor affecting soil compaction in comparison to the inflation pressure of tire.

• 대한토목학회논문집
• /
• 제26권4D호
• /
• pp.601-608
• /
• 2006

포장을 설계하고 설계 수명을 산정하거나 현재 공용중인 포장의 유지 관리를 위한 상태 평가를 수행해야하는 경우 포장의 거동 분석은 중요한 입력 변수로 작용하게 된다. 포장의 거동을 예측하기 위해서는 정확한 타이어의 접지면적과 타이어의 압력이 필요하다. 따라서 본 연구에서는 실제 측정된 타이어의 형상을 측정하여 PCA에서 제안한 타이어의 형상과 비교하고, 측정된 타이어의 접지면적과 타이어의 종류에 대한 타이어 압력분포를 사용하여 3차원 유한요소해석을 통하여 포장의 거동을 예측하고 예측된 포장의 거동과 실제 포장의 거동을 비교 분석하였다. 해석 결과 표층의 경우 타이어의 형상과 비선형 압력분포의 영향을 크게 받으며, 이러한 타이어의 특성을 고려함으로써 현장 거동을 보다 잘 설명할 수 있는 것으로 나타났다. 하지만 중간층의 경우 타이어의 영향이 크지 않은 것으로 나타났으며, 실제 현장 거동과 비교했을 때 타이어 하부에서는 큰 차이를 보여주어 실제 포장의 거동을 보다 정확하게 예측하기 위해서는 이 부분을 보다 명확하게 설명을 할 수 있어야 할 것으로 나타났다.

• 한국도로학회논문집
• /
• 제10권2호
• /
• pp.47-55
• /
• 2008

본 논문에서는 3차원 유한요소법과 층탄성프로그램인 BISAR를 통해 얇은 아스팔트 콘크리트 표층의 피로균열 수명에 영향을 줄 수 있는 아스팔트 표층에서의 예측 인장변형률 결과를 광폭타이어와 바이어스 프라이 타이어를 이용하여 비교하였다. 본 논문에서는 11R22.5와 $10{\times}20$ bias ply 타이어의 접지압력 분포도를 분석하였으며, 서로 다른 해석방법을 이용하여 아스팔트 표층 하단부와 상단부에서의 예측인장변형률을 비교하였다. 분석결과, 두 타이어의 접지압 분포는 유사했지만 11R22.5광폭타이어가 $10{\times}20$ bias ply타이어와 비교해 상당히 큰 연직방향 접지압력을 보였다. 타이어 중앙에서 아스팔트 콘크리트 표층 하단부에서의 예측 인장변형률은 타이어 접지면적을 측정하여 충탄성프로그램인 BISAR에 적용한 BM해석법이 컸으며, 타이어 가장자리로부터 3.5cm 떨어진 곳에서의 상층부 예측 인장변형률은 3차원 접지압을 이용한 3차원유한요소법에 의한 해석이 가장 큰 값을 보였다.

• 대한기계학회논문집
• /
• 제13권5호
• /
• pp.820-830
• /
• 1989

본 논문에서는 타이어의 각 부분의 물성치 계산을 위한 식을 유한요소법에 적용할 수 있도록 제안하였다. 이 식은 강철 코드의 굽힙효과를 고려 하였으며, 특히 각 요소에서 전단변형이 일어나는 동안의 굽힘효과를 고려하였다. 유한요소 공식화는 가상일의 원리에 의하여 평형 방정식으로부터 유도하였고, Updated refer- ence coordinate에 대해 증분해석을 적용하여 Updated Lagrangian공식화를 하였다. 그리고 차량하중에 의하여 타이어가 노면에 접지될때의 응력상태를 게산할 수 있도록 접촉문제 공식화를 유한요소 공식화에 첨가 하였다.

• 농업과학연구
• /
• 제47권4호
• /
• pp.1147-1158
• /
• 2020

The purpose of this study was to measure the engine torque and rotational speed of a 67 kW class agricultural tractor according to tire type during plow tillage and to analyze the gear strength of the driving shift for the tractor. A field test was performed under the condition with a single tire (Test A) and dual tires (Test B) to increase the ground width of the rear tires. A load monitoring system was developed, and the engine torque and rotational speed were measured using controller area network (CAN) communication. The engine torque and rotational speed during plow tillage were calculated as the equivalent torque and speed using Palmgren Miner's rule. As a result, the equivalent torque and speed in Test A and Test B were 181.0 Nm and 1,913 rpm and 206.1 Nm and 2,130 rpm, respectively. As the ground width of the rear tire was increased, the bending stress in Test B was about 9.9 to 10.5% higher than that of the Test A, and the contact stress was about 4.6 to 4.9% higher than that of the Test A. Under all conditions, the safety factor for the bending and contact stress was 1 or more. Thus, the driving shift gears for the dual tire type are considered safe.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1998년도 동계 학술대회 논문집
• /
• pp.36-41
• /
• 1998

• 한국항공우주학회지
• /
• 제39권8호
• /
• pp.719-724
• /
• 2011

비공기압 타이어(Non-Pneumatic tire)는 공기압 타이어와는 다르게 스포크(Spoke)로 공기압의 역할을 담당하는 새로운 타이어이다. 이 타이어는 공기압 타이어의 펑크에 대한 위험과 공기압 유지가 필요 없는 장접을 가졌으며, 공기가 존재하지 않는 우주에서도 사용이 가능하다. 본 연구에서는 음의 각으로 이뤄진 허니컴 구조의 비공기압 타이어를 수직 하중에 따른 접지압을 구하여, 이를 공기압 타이어와 비교하였다.