• 한국재료학회지
• /
• 제19권12호
• /
• pp.649-656
• /
• 2009

Inorganic oxide colloids dispersed in alcohol were applied to a stainless steel substrate to produce oxide coatings for the purpose of minimizing emissive thermal transfer. The microstructure, roughness, infrared emissive energy, and surface heat loss of the coated substrate were observed with a variation of the nano oxide sol and coating method. It was found that the indium tin oxide, antimony tin oxide, magnesium oxide, silica, titania sol coatings may reduce surface heat loss of the stainless steel at 300${\circ}C$. It was possible to suppress thermal oxidation of the substrate with the oxide sol coatings during an accelerated thermal durability test at 600${\circ}C$. The silica sol coating was most effective to suppress thermal oxidation at 600${\circ}C$, so that it is useful to prevent the increase of radiative surface heat loss as a heating element. Therefore, the inorganic oxide sol coatings may be applied to improve energy efficiency of the substrate as the heating element.

• 전기화학회지
• /
• 제3권1호
• /
• pp.15-18
• /
• 2000

태양전지의 전극 기판으로 사용되는 전도성 투명 산화주석 박막의 제조 방법에 대하여 연구하였다. 졸겔법을 이용하여 산화 주석 박막을 제조하는 경우에 저가의 공정으로 대면적의 박막을 얻을 수 있는 장점이 있다. 본 연구에서는 공정 조건의 확립과 전구체의 설정에 중점을 두었다. 전구체 용액을 isopropyl 알코올에 tin isopropoxide를 용해한 용액을 사용하였으며 수화 반응을 억제하기 위하여 triethanolamine(TEA)을 첨가하였다. Corning유리 위에 spinning과 dipping방법을 이용하여 코팅을 하였으며 이후 열처리하여 최종 산화주석 박막을 제조하였다. 이렇게 제조된 박막은 가시광선 영역에서 $90\%$ 이상의 투과도를 보였으며 $0.01\Omega{\cdot}cm$ 이하의 비저항을 나타냈다

• 마이크로전자및패키징학회지
• /
• 제15권2호
• /
• pp.17-21
• /
• 2008

Sn-Cu계 솔더 범프에서 무전해도금법을 이용한 범프 형성에 대한 연구를 하였다. $20{\mu}m$ via에 전기도금법으로 구리를 채운 웨이퍼 위에 ball형태의 범프를 형성하기 위하여 구리와 주석을 도금하여 약 $10{\mu}m$높이의 범프를 형성하였다. 구리 범프 형성 시 via위에 선택적으로 도금하기 위하여 활성화 처리 후 산세처리를 실시하고 무전해 도금액에 안정제를 첨가하였다. 무전해도금법을 이용하여 주석 범프 형성 시 도금층이 구리 범프에 비해 표면의 균일도가 벌어지는 것으로 관찰되었지만 reflow공정을 실시한 후 ball 형태의 균일한 Sn-Cu 범프를 형성하였다.

• Journal of Welding and Joining
• /
• 제15권5호
• /
• pp.74-83
• /
• 1997

Effect of welding parameters such as current, speed and electrode pressure on the weld quality of tin coated steels for small containers was discussed in this paper. Welding was performed with low frequency wire seam welding system which was loaded with 1.5mm in diameter copper wire electrode. The welding parameters were monitored at the position close to the welding spot so as to minimize the instrumentation error, and the signals were stored into a digital data acquisition system before analysis. Results showed that critical current for sufficient nugget size increased as the base material thickness increased, while the width of the optimum welding range was reduced. The acceptable welding condition derived from this study was found to be effective within the thickness range of $\pm$10% of the nominal (0.25mm) thickness. Tin coating layer was proved not to affect seriously on the weld quality, i.e. strength and formability, since consumable wire electrode was used in this process. Test results also demonstrated that the welding current was thought to be the most effective parameter to form an acceptable weld, while welding speed or electrode pressure exerted less effect on the nugget formation. However, these two parameters played an important role because the former was related to the nugget overlap interval, and the latter, to the formation of expulsion during welding.

• 한국세라믹학회지
• /
• 제44권6호
• /
• pp.313-318
• /
• 2007

ITO (Indium-tin oxide) thin films have been prepared by a sol-gel spinning coating method and fired and annealed in the temperature range of $450-600^{\circ}C$. The XRD patterns of the films indicated the main peak of (222) plane and showed higher crystallinity with increasing an annealing temperature. The surface of the ITO thin films were treated with 0.1 N HCl 20% solution at room temperature. The effects of surface treatment on electrical properties and surface morphologies of the ITO films were investigated with the results of sheet resistance and FE-SEM, AFM images. The samples, subsequently treated with acidic solution for 40 sec showed the sheet resistance of $0.982\;k{\Omega}/square$. The surface treatment using acidic solution diminished the RMS (root mean square) value and the residual carbon content of the ITO films. It seemed that the acid-cleaning of the ITO thin films lead to the decrease of surface roughness and sheet resistance.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2006년도 춘계학술발표회 초록집
• /
• pp.91-91
• /
• 2006

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2003년도 춘계총회 및 연구발표회 초록집
• /
• pp.179.1-179
• /
• 2003

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2003년도 추계총회 및 연구발표회 초록집
• /
• pp.73.2-73
• /
• 2003

• 한국세라믹학회지
• /
• 제33권7호
• /
• pp.839-847
• /
• 1996

• 대한치과보철학회지
• /
• 제45권3호
• /
• pp.329-338
• /
• 2007

Purpose. The aim of this study is to evaluate the effect of TiN coating of abutment screw on the unscrewing torque. Material and methods. Titanium and Gold-Tite abutment screws were classified into two groups, Group A and C respectively, as control groups. Titanium abutment screws with TiN coatings were also classified into two groups, Group B and D, as experimental ones. Group A and B were tightened to 20 Ncm input torque, and Group C and D were tightened to 32 Ncm torque. Detorque values were measured with digital torque gauge during repeated closing and opening experiment. Results. Abutment screws with TiN coating (Group B and D) showed statistically significant higher mean detorque values than those of Group A and C. Discussion. Physical properties of TiN coating, such as low friction coefficient, high hardness and wear resistance, might contribute to higher detorque values. Conclusion. It is suggested that TiN coating of abutment screw help to reduce the risk of screw loosening and improve the stability of screw joint.