• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.4
• /
• pp.93-100
• /
• 2009

Intake/exhaust valve timing and exhaust cam lift were changed to control the internal exhaust gas recirculation (IEGR) and combustion phase of homogeneous charge compression ignition (HCCI) engine. To measure the IEGR rate, in-cylinder gas was sampled during from intake valve close to before ignition start. The lower exhaust cam made shorter valve event than higher exhaust cam and made IEGR increase because of trapping the exhaust gas. IEGR rate was more affected by exhaust valve timing than intake valve timing and increased as exhaust valve timing advanced. In-cylinder pressure was increased near top dead center due to early close of exhaust valve. Ignition timing was more affected by intake valve timing than exhaust valve timing in case of exhaust valve lift 8.4 mm, while ignition timing was affected by both intake and exhaust valve timing in case of exhaust valve 2.5 mm. Burn duration with exhaust valve lift 2.5 mm was longer than other case due to higher IEGR rate. The fuel conversion efficiency with higher exhaust valve lift was higher than that with lower exhaust valve lift. The late exhaust and intake maximum open point (MOP) made the fuel conversion efficiency improve.

• Phonetics and Speech Sciences
• /
• v.3 no.3
• /
• pp.69-75
• /
• 2011

This paper investigates phrase positional effects on the timing of F0 (pitch) peaks in Tokyo Japanese disyllabic words with varying accent type (HL or LH) and phrase position (final or non final). The F0 peak timing was normalized by the total word duration ('normalized H timing'). The normalized H timing was significantly affected by accent type and phrase position. The H timing was later in the LH accent type than in the HL accent type, and in non final positions than in final positions. In addition, to examine the validity of the quantitative results, different models of phrase position effects were compared by measuring H timing in two approaches: normalization versus relative distance measures. For the normalization measures, the H timing was measured as the time of the F0 peak divided by the total word duration or by the duration of the tone bearing syllable. For the relative distance measures, the H timing was measured as the distance in milliseconds from the end of the word or from the end of the associated syllable. The best model was the normalization by the total word duration, rather than by the duration of the tone bearing syllable. This means that phrase positional effects on the timing of F0 peaks in Japanese disyllabic words are best modeled in terms of proportion of the total word duration.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.6A
• /
• pp.685-692
• /
• 2008

In this paper, we propose a timing recovery loop for Inmarsat mini-m system downlink receiver. Inmarsat mini-m system requires a timing recovery loop which is robust in frequency offset and has fast acquisition because Inmarsat mini-m system specification requires frequency tolerance is required of ${\pm}924$ Hz (signal bandwidth: 2.4 kHz) and acquisition time of UW (Unique Word) signal duration (15ms).Therefore, we propose a timing recovery loop which is suitable for Inmarsat mini-m system. The proposed timing recovery loop adopted noncoherent UW detector and differential ELD which applied differential UW signal for stability and fast acquisition in frequency offset environment. Simulation results show that the proposed timing recovery loop has stable operation and fast acquisition in frequency offset environment for the system.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.3
• /
• pp.122-129
• /
• 1996

The spark timing is one of major parameters to the engine performance and emissions. The ECU controls the spark timing based on preset values, which are functions of load and speed, in most of today's automotive SI engine. In this system, the preset spark timing can be different from optimum value due to the deviations from mass production, aging effects and so on. In the present study, a control logic is investigated for real time adaptation of spark timing to optimal value. It has been found that crank angle of miximum cylinder pressure is one of the appropriate parameters to estimate the optimum spark timing throught experiment. It has also been observed for spark timing convergence by variation of engineering model factors. The simulation program including engineering model for cycle by cycle variation of combustion is developed for surveying spark timing control logic. It is also shown that simulation results reflect experiment outputs and reasonableness of spark timing control logic for crank angle of maximum cylinder pressure.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.6C
• /
• pp.623-628
• /
• 2006

This paper addresses the frequency offset estimation problem in the presence of the timing error for OFDM systems. When the timing error exists, the correlation value used for the frequency offset estimation could be reduced significantly due to the timing error, resulting in considerable degradation in estimation performance. In this paper, using the coherence phase bandwidth (CPB) and a threshold, a novel frequency offset estimation scheme is proposed and based on which, an efficient timing error estimation scheme is also proposed for the re-estimation of the frequency offset. The performance comparison results show that the proposed frequency offset estimation scheme is not only more robust to the timing error but also has less computational complexity, as compared with the conventional schemes. It is also demonstrated by simulation that theproposed timing error estimation scheme gives a reliable estimate of the timing error.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.1C
• /
• pp.40-44
• /
• 2010

The timing error detector(TED) employed in the closed loop type timing synchronization scheme for an MQASK all digital receiver suffers from the selfnoise-induced timing jitter. To eliminate the timing jitter a prefilter can be added in front of the TED. The prefilter method, however, degrades the stability and timing acquisition performance due to the loop delay and increases the complexity of the synchronizer. This paper proposes a polyphase filter type resampler approach to optimize the performance and architecture of the synchronizer simultaneously. The proposed scheme uses two resamplers which performs matched filtering and matched prefiltering so that the loop delay is minimized with minimal hardware resources. Simulation results showed an excellent acquisition performance with reduced timing jitter.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.13 no.4
• /
• pp.1866-1883
• /
• 2019

As the youngest branch of information hiding, network covert timing channels conceal the existence of secret messages by manipulating the timing information of the overt traffic. The popular model-based framework for constructing covert timing channels always utilizes cumulative distribution function (CDF) of the inter-packet delays (IPDs) to modulate secret messages, whereas discards high-order statistics of the IPDs completely. The consequence is the vulnerability to high-order statistical tests, e.g., entropy test. In this study, a rich security model of covert timing channels is established based on IPD chains, which can be used to measure the distortion of multi-order timing statistics of a covert timing channel. To achieve rich security, we propose two types of covert timing channels based on nested lattices. The CDF of the IPDs is used to construct dot-lattice and interval-lattice for quantization, which can ensure the cell density of the lattice consistent with the joint distribution of the IPDs. Furthermore, compensative quantization and guard band strategy are employed to eliminate the regularity and enhance the robustness, respectively. Experimental results on real traffic show that the proposed schemes are rich-secure, and robust to channel interference, whereas some state-of-the-art covert timing channels cannot evade detection under the rich security model.

• Journal of IKEEE
• /
• v.25 no.2
• /
• pp.234-242
• /
• 2021

In case implementation of microwave photonic (MWP) systems for phased array radars (PARs), noise and time delay error should be minimized to obtain accurate beam direction. Time delay error in MWP systems is generated from signal noise and timing jitter. In this paper, noise and timing jitter in MWP systems for PAR is researched, also according to the amplification of an erbium-doped fiber amplifier, noise and timing jitter variation is verified by an experiment. Timing jitter is decreased and SNR is increased if we amplify the signal by using an erbium-doped fiber amplifier, up to the amplification rate of signal and noise is similar.

• ETRI Journal
• /
• v.37 no.2
• /
• pp.406-416
• /
• 2015

Timing plays a key role in expressing the qualitative aspects of a character's motion; that is, conveying emotional state, personality, and character role, all potentially without changing spatial positions. Temporal editing of locomotion style is particularly difficult for a novice animator since observers are not well attuned to the sense of weight and energy displayed through motion timing; and the interface for adjusting timing is far less intuitive to use than that for adjusting pose. In this paper, we propose an editing system that effectively captures the timing variations in an example locomotion set and utilizes them for style transfer from one motion to another via both global and upper-body timing transfers. The global timing transfer focuses on matching the input motion to the body speed of the selected example motion, while the upper-body timing transfer propagates the sense of movement flow - succession - through the torso and arms. Our transfer process is based on key times detected from the example set and transferring the relative changes of angle rotation in the upper body joints from a timing source to an input target motion. We demonstrate that our approach is practical in an interactive application such that a set of short locomotion cycles can be applied to generate a longer sequence with continuously varied timings.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.3
• /
• pp.307-312
• /
• 2002

A study on the exhaust emissions of marine diesel engine with various fuel injection timing is performed experimentally .In this paper, fuel injection timing is changed from BTDC $14^{\circ}$ to $20^{\circ}$ by $2^{\circ}$ intervals, the experiments are performed at engine speed 1800rpm and from load 0% to 100% by 25% intervals, and main measured parameters are fuel consumption rate, Soot, NOx, HC and CO emissions etc. The obtained conclusions are as follows (1) Specific fuel consumption is indicated the least value at BTDC $18^{\circ}$ of fuel injection timing and it is increased in case of leading the injection timing. (2) Soot emission is decreased in case of leading fuel injection timing and it is increased in the form of convex downwards with increasing the load. (3) NOx emission is increased in case of leading fuel injection timing and it is increased in the form of straight line nearly with increasing the load. (4) HC and CO emissions are decreased in case of leading fuel injection timing and they are changed in the form of convex downwards with increasing the load.