• Structural Monitoring and Maintenance
• /
• v.2 no.2
• /
• pp.133-143
• /
• 2015

Civil engineering infrastructure is aging and requires cost-effective maintenance strategies to enable infrastructure systems operate reliably and sustainably. This paper presents an approach for determining risk-cost balanced repair strategy of corrosion damaged reinforced concrete structures with consideration of uncertainty in structural resistance deterioration. On the basis of analytical models of cover concrete cracking evolution and bond strength degradation due to reinforcement corrosion, the effect of reinforcement corrosion on residual load carrying capacity of corroded reinforced concrete structures is investigated. A stochastic deterioration model based on gamma process is adopted to evaluate the probability of failure of structural bearing capacity over the lifetime. Optimal repair planning and maintenance strategies during the service life are determined by balancing the cost for maintenance and the risk of structural failure. The method proposed in this study is then demonstrated by numerical investigations for a concrete structure subjected to reinforcement corrosion. The obtained results show that the proposed method can provide a risk cost optimised repair schedule during the service life of corroded concrete structures.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.2D
• /
• pp.237-245
• /
• 2011

Asphalt Plug Joint(APJ) is a new type of expansion joint that it's application are increased in USA as well as several European countries. APJ's' advantages are cheap construction and maintenance costs, and simple construction and securing of excellent flatness. However, APJ's usability is hindered because it showed a problem of premature failure. Research for solving this problem has been progressed, and FEM analysis among existing researches was peformed. However, the behavior of APJ was insufficiently analyzed and the reliability of the analysis was much low, since the material showing complicated behavior was oversimplified, Therefore, a material model was proposed and its effectiveness was confirmed by comparing it with actual behavior in order to improve the reliability of FEM analysis in this paper. ABAQUS program was used for FEM analysis, and an elasto-plastic model and a viscous-plastic model as the material model of APJ were suggested on the base of experiment results of APJ material performed by Bramel et al. The elasto-plastic model was defined by time-independent analysis since it didn't consider time and strain rate, and the viscous-plastic model was defined by time-dependent analysis since it considered. Influence of various elements affecting the behavior of APJ was investigated, and it was confirmed that the time-dependent analysis showed better result closed to actual behavior than the time-independent analysis.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.04a
• /
• pp.537-544
• /
• 2003

This paper deals with stress corrosion cracking behavior of high strength steel exposed to marine environments. The objective is to determine the time to failure as a function of hydrogen concentration and tensile stress in the wires. A crack growth curve is modeled using finite element method (FEM) program. The coupled hydrogen diffusion-stress analyses of SCC were programmed separately. The first part is calculating stress and stress intensity /sup 1)/factor of a cylindrical shell, prestressing tendon or suspension bridge wires, from the initiation of cracks to rupture. Virtual crack extension method, contour integral method, and crack tip elements are used for the calculation of stresses in front of the crack tip. Comparisons of the result show a good agreement with the analytical equations and wire tests. The second part of the study deals with the programming of hydrogen diffusion, affected by hydrostatic stress, calculated at the location of boundary of plastic area around the crack tip. The results of paper can be used in the design and management of prestressed structures, cable stayed and suspension bridges. Time dependent correlated parallel reliabilities of a cable, composed of 36 wires, were evaluated by the consideration of the deterioration of stress corrosion cracking.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.11
• /
• pp.1365-1373
• /
• 1999

In many countries including Korea, in order to transmit the more electric power, the higher transmission line voltage is inevitable. So, a rapid reclosing scheme is important for EHV/UHV transmission lines to ensure requirements for high reliability of main lines. A critical aspect of reclosing operation is the extinction of the secondary arc since it must extinguish before successful reclosure can occur. Therefore the accurate simulation techniques of arcing faults are of importance. And successful reclosing switching can be accomplished by adopting a proper method such as HSGS and hybrid scheme to reduce the secondary arc extinction time. First of all, this paper discusses a suggested arc model, which have time dependent resistance for primary arc and piecewise linear approximated arc model for secondary arc. And this simulation technique is applied to Korean 765 kV transmission lines. Also hybrid scheme is simulated and evaluated for the purpose of shortening dead time. For adaptive reclosing scheme, variable dead time control algorithm is suggested. Two kinds of algorithm are tested. One is max tracking algorithm and the other is rms tracking algorithm. According to simulation results, rms tracking has less errors than max tracking. Therefore rms tracking is applied to Korean 765 kV transmission lines with hybrid scheme.

• Journal of Information Technology Application
• /
• v.3 no.3
• /
• pp.91-106
• /
• 2001

We propose a software-reliability growth model incoporating the amount of uniform and Weibull testing efforts during the software testing phase in this paper. The time-dependent behavior of testing effort is described by uniform and Weibull curves. Assuming that the error detection rate to the amount of testing effort spent during the testing phase is proportional to the current error content, the model is formulated by a nonhomogeneous Poisson process. Using this model the method the data analysis for software reliability measurement is developed. The optimum release time is determined by considering how the initial reliability R($\chi$ 0) would be. The conditions are ($R\chi$ 0)＞$R_{o}$ , $P_{o}$ ＞R($\chi$ 0)＞ $R_{o}$ $^{d}$ and R($\chi$ 0)＜$R_{o}$ $^{d}$ for uniform testing efforts. deal case is $P_{o}$ ＞($R\chi$ 0)＞ $R_{o}$ $^{d}$ Likewise, it is ($R\chi$ 0)$\geq$$R_{o}$ , $R_{o}$ ＞($R\chi$ 0)＞R(eqation omitted) and ($R\chi$ 0)＜R(eqation omitted)for Weibull testing efforts. Ideal case is $R_{o}$ ＞ R($\chi$ 0)＞ R(eqation omitted).

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.3
• /
• pp.186-195
• /
• 2000

In this paper, partial discharge (PD) measurement was performed to evaluate the quality of the cable joint and termination constructions. The resistive coupling technique for PD detection using resistivity of semiconducting layer of the cable in the accessories, such as joints and terminations. With high frequency PD (HEPD) measurement, an excellent sensitivity below 20pC could be achieved under unshielded condition. The localization of the defects in the accessories could be identified. During heating cycle, PDs were monitored and analyzed. At that time, the PDs were dependent on the temperature of the heating cycle and showed cyclic behaviors, which were attributed to local delamination of the interfaces, between epoxy unit and stress relief cone(SRC) and between SRC and cable, due to the difference of thermal expansion. As a conclusion, HFPD measurement technique was proven to be an effective diagnostic method for qualification of extra high voltage (EHV) cable accessories. With this technique, the optimal design of the components of the accessories could be verified not only in an early stage but also under operating condition. This technique would result in the improvement of the reliability of the EHV cable accessories.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.9
• /
• pp.20-28
• /
• 1992

Dielectric thin film of N/O ($Si_{3]N_{4}/SiO_{2}$) for high density stacked dynamic-RAM cell was formed by LPCVD and oxidation(dry & pyrogenic oxidation methods) of the top 7nm $Si_{3]N_{4}$ film. The thickness, structure and composition of this film were measured by ellipsometer, high resolution TEM, AES and SIMS. The insulating characteristics(I-V characteristics) were investigated by HP 4145, and the characteristics of TDDB (Time Dependent Dielectric Breakdown) were evaluated by using CCST(Current Constant Stress Time) method. In this experiment, The optimum oxidation condition for preparation of good insulating and TDDB characteristics of N/O film was pyrogenic oxidation at 85$0^{\circ}C$ for 30 minutes. The leakage current was reduced from 400pA to 7.5pA when SiO$_{2}$ film with thickness of 2nm was formed on the top of $Si_{3]N_{4}$ film by the pyrogenic oxidation method.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1086-1091
• /
• 2004

The boundary layer is a very important characteristic of a liquid-vapor interface since it governs the heat and mass transfer phenomena across an interface. However, the thickness of a boundary layer is generally micro- or nano-sized, which requires highly accurate measurement devices and, consequently, costs the related experiments very high and time-consuming. Due to these size dependent limitations, the experiments related with a nano-scaled size have suffered from the errors and the reliability of the obtained data. This study is performed to grasp the characteristics of a liquid-vapor interface, by using a molecular dynamics method. The simulation results were compared with other studies if possible. Although other studies reported that there existed a temperature discontinuity over an interface when the system was reduced to micro- or nano-sized, we confirmed that there was no such a temperature discontinuity.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2003.10a
• /
• pp.113-117
• /
• 2003

The reliability of machined fiber reinforced composites (FRC) in high strength applications and the safety in using these components are often critically dependent upon the quality of surface produced by machining since the surface layer may drastically affect the strength and chemical resistance of the material [1,2,3,4]. Current study will discuss the characterization of fiber pull-out in orthogonal cutting of a fiber-matrix composite materials. A sparsely distributed idealized model composite material, namely a glass reinforced polyester (GFRP) was used as workpiece. Analysis method employs a force sensor and the signals from the sensor are processed using AR time series model. The experimental correlation between the fiber pull-out and the AR coefficients is examined first and effects of fiber orientation, cutting parameters and tool geometry on the fiber pull-out are also discussed.

• Proceedings of the KIEE Conference
• /
• 1990.07a
• /
• pp.177-179
• /
• 1990

Recently, it is reported that the behaviour of PECVD under high electric field and current condition has a major effect on MNS device degradation. In this paper, we evaluated the breakdown and TDDB characteristics of Laser assisted PECVD SiN films which is introduced new deposited method. And also, long term insulator breakdown reliability is described by examing time dependent dielectric breakdown under positive voltage. Failure tines against electric field are examined and acceleration factors are obtained for each case. From these data, breakdown wearout limitation for Laser Assisted PECVD SiN film can be characterized.