• 대한기계학회논문집A
• /
• 제30권11호
• /
• pp.1494-1501
• /
• 2006

Mechanical and physical properties of a copper alloy for a liquid rocket engine(LRE) combustion chamber liner application were tested at various temperatures. All test specimens were heat treated with the condition they might experience during actual fabrication process of the LRE combustion chamber. Physical properties measured include thermal conductivity, specific heat and thermal expansion data. Uniaxial tension tests were preformed to get mechanical properties at several temperatures ranging from room temperature to 600$^{\circ}C$. The result demonstrated that yield stress and ultimate tensile stress of the copper alloy decreases considerably and strain hardening increases as the result of the heat treatment. Since the LRE combustion chamber operates at higher temperature over 400$^{\circ}C$, the copper alloy can exhibit time-dependent behavior. Strain rate, creep and stress relaxation tests were performed to check the time-dependent behavior of the copper alloy. Strain rate tests revealed that strain rate effect is negligible up to 400$^{\circ}C$ while stress-strain curve is changed at 500$^{\circ}C$ as the strain rate is changed. Creep tests were conducted at 250$^{\circ}C$ and 500$^{\circ}C$ and the secondary creep rate was found to be very small at both temperatures implying that creep effect is negligible for the combustion chamber liner because its operating time is quite short.

• 한국산학기술학회논문지
• /
• 제7권3호
• /
• pp.409-413
• /
• 2006

미시학적 비배수 크리프 현상의 누적 변형은 점성토 시공지역 지반의 전반 파괴를 야기 할 수 있다. 본 연구에서는 점성토의 비배수 크리프 거동을 예측하기 위하여 Perzyna의 일반 점성이론을 소성론의 개념에서 간략화하고 수정 Cam clay 모델 및 데미지 이론을 포함하는 하나의 시간의존적 구성방정식을 유도하였다. 유도된 구성방정식을 활용하여 예측한 크리프 거동은 비배수 크리프 파괴를 포함하는 크리프 실험결과와 잘 부합하였다.

• Structural Engineering and Mechanics
• /
• 제52권1호
• /
• pp.97-113
• /
• 2014

In the present work appropriate concrete material models have been proposed to predict drying shrinkage and specific creep of High-performance concrete (HPC) using Artificial Neural Network (ANN). The ANN models are trained, tested and validated using 106 different experimental measured set of data collected from different literatures. The developed models consist of 12 input parameters which include quantities of ingredients namely ordinary Portland cement, fly ash, silica fume, ground granulated blast-furnace slag, water, and other aggregate to cement ratio, volume to surface area ratio, compressive strength at age of loading, relative humidity, age of drying commencement and age of concrete. The Feed-forward backpropagation networks with Levenberg-Marquardt training function are chosen for proposed ANN models and same implemented on MATLAB platform. The results shows that the proposed ANN models are more rational as well as computationally more efficient to predict time-dependent properties of drying shrinkage and specific creep of HPC with high level accuracy.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.433-436
• /
• 2003

This paper proposes rheological creep and shrinkage model of FCM bridges made for HPC about 40Mpa. The proposed model separates time dependent part with characteristic material part and regards main variable as elastic modulus, which represents material characteristic and history. To find parameters of the model, we had creep, shrinkage and basic material tests about four FCM bridges. All specimens were tested with same condition, after 3days, 28days and 90days of curing. Also, exposed condition and closed condition were separately given to compare the data of each bridge. Finally, all creep data of four FCM bridges were compared to proposed rheological model and other proposed world code models, AASHTO, ACI, CEB-FIP, JSCE and etc.

• 한국지반공학회지:지반
• /
• 제3권4호
• /
• pp.7-20
• /
• 1987

연약지반의 다차원 압밀해석을 유한요소법으로 해석하기 위하여 점토의 구성방정식으로서 신생퇴적 점토층에서 압밀시에 예상되는 creep와 같은 변형의 시간의존성거동을 표친하는 탄 점소성 구성방정식을 새로히 제안하기 위하여 한계상태 개념으로부터 개발된 수정 cam clay 모델을 보완하여 음력변형해석을 통하여 실측치와 비교한 것이다. 그 결과 대체적으로 실측치와 접근하고 있음을 알 수 있었다.

• 대한토목학회논문집
• /
• 제1권1호
• /
• pp.53-68
• /
• 1981

지속하중하(持續荷重下)의 점토지반(粘土地盤) 또는 사면(斜面)을 형성(形成)하고 있는 점토(粘土)는 시간의존변형(時間依存變形)을 일으키고 어떤 경우 파괴(破壞)에 이르기도 하는데 그 원인(原因)은 점토(粘土)의 Creep 거동(擧動) 때문이라는 보고(報告)가 대부분(大部分)이다. Creep 거동(擧動)은 많은 요소(要素)에 관련될 뿐 아니라 특(特)히 함수비(含水比) 및 응력수준(應力水準)에 큰 영향(影響)을 받기 때문에 매우 복잡(複雜)하며 따라서 그 거동(擧動)을 해석(解析) 하기도 어려운 일인데 Creep이 궁극적(窮極的)으로는 점토(粘土) 입자간(粒子間)의 미시적(微視的)인 거동(擧動)에서 비롯되기 때문이다. 응력(應力)-변형(變形)-시간(時間) 관계(關係)로서의 Creep 거동(擧動)을 수학적(數學的)으로 표현(表現)하기 위하여 여러 형태(形態)의 유변학적(流變學的) 모델이 제안(提案) 되었다. 유변학적(流變學的) 모델은 선형(線形) 스프링, 비선형(非線形) Dashpot 및 Slider를 조합(組合)한 것인데 점토(粘土)의 변형(變形)에 관한 탄성적(彈性的), 소성적(塑性的) 및 점성적(粘性的) 성분(成分)을 구분(區分) 하는데 매우 유용(有用)하다. 그러나 대부분(大部分)의 경우, 유변학적(流變學的)모델은 포화(飽和)된 점토(粘土)에 대(對)하여 주(主)로 2차압밀(次壓密) 거동(擧動)을 밝히기 위하여 제안(提案)된 것으로 비포화점토(非飽和粘土)에 대(對)한 보고(報告)는 매우 드문 것 같다. 한편, Creep 거동(擧動)은 시간의존변형(時間依存變形)이므로 흐트러진 점토(粘土)를 다져서 시험(試驗)하는 경우, 시간경과(時間經過)에 따라 Thixotropy 문제(問題)가 제기(提起)될 것이고 배수조건(排水條件)과 관련하여서는 공시체(供試體)의 높이가 문제(問題)될 수 있다. 그뿐 아니라 많은 연구결과(硏究結果)에 의(依)하면 응력증가초기(應力增加初期)에는 시간지체(時間遲滯)가 없는 초기탄성변형(初期彈性變形)이 발생(發生)된다고 하므로 유변학적(流變學的) 모델에는 이를 나타내는 요소(要素)가 반드시 필요(必要)하게 될 것이다. 본(本) 연구(硏究)는 이러한 면(面)에 초점(焦點)을 두고 함수비(含水比)와 응력수준(應力水準)을 여러 가지로 변화(變化)시켰을 때의 Creep 거동(擧動)을 유변학적(流變學的) 모델로 해석(解析)함에 있어 소성(塑性)이 비교적(比較的) 큰 3종(種)의 점토(粘土)를 사용(使用)하여 초기탄성변형(初期彈性變形) 거동(擧動)을 밝히고 Thixotropy 효과(効果) 및 공시체(供試體)의 높이가 Creep 거동(擧動)에 끼치는 영향(影響)을 구명(究明)하며 아울러 유변학적(流變學的) 모델의 어떤 요소(要素)에 관련 되는가를 알아내기 위하여 다져서 성형(成形)한 공시체(供試體)로서 일축배수형식(一軸排水形式)의 Creep 거동(擧動)을 시행(施行)하였다. 실험결과(實驗結果) 및 검토(檢討)에 의(依)하면 응력재하(應力載荷) 및 증가초기(增加初期)에는 시간지체(時間遲滯)가 없는 탄성적(彈性的) 초기변형(初期變形)이 발생(發生)하고 따라서 유변학적(流變學的) 모델에는 이를 나타내기 위한 상부(上部)스프링을 설치(設置)해야 하며 Thixotropy 효과(効果)를 고려(考慮)한 경우, Creep변형(變形)은 완만(緩慢)하게 되나 함수비(含水比) 및 응력수준(應力水準)에 따른 상태거동(狀態擧動)은 같으므로 그 차이(差異)는 모델 상수(常數)의 크기에만 관련됨을 알아내었고 따라서 동일(同一)한 유변학적(流變學的) 모델로 그 거동(擧動)을 나타낼 수 있다는 사실(事實)을 밝혀 냈다. 또 공시체(供試體) 높이를 작게 한 경우에는 함수비(含水比)가 비교적(比較的) 작아서 점(粘)-소(塑)-탄성(彈性) 및 점(粘)-탄성(彈性)일 때만 높이가 클 때와 같은 상태거동(狀態擧動)을 나타내어 동일(同一)한 유변학적(流變學的) 모델로 나타낼 수 있고 함수비(含水比)가 큰 점일소성(粘一塑性) 및 점성류(粘性流)일 때는 그 상태거동(狀態擧動)이 배수문제(排水問題)와 관련하여 달라지게 되고 따라서 유변학적(流變學的) 모델도 달라지게 된다는 사실(事實)을 발견(發見) 하였다.

• Steel and Composite Structures
• /
• 제10권1호
• /
• pp.45-67
• /
• 2010

Composite steel-concrete structures are employed extensively in modern high rise buildings and bridges. This concept has achieved wide spread acceptance because it guarantees economic benefits attributable to reduced construction time and large improvements in stiffness. Even though the combination of steel and concrete enhances the strength and stiffness of composite beams, the time-dependent behaviour of concrete may weaken the strength of the shear connection. When the concrete loses its strength, it will transfer its stresses to the structural steel through the shear studs. This behaviour will reduce the strength of the composite member. This paper presents the development of an accurate finite element model using ABAQUS to study the behaviour of shear connectors in push tests incorporating the time-dependent behaviour of concrete. The structure is modelled using three-dimensional solid elements for the structural steel beam, shear connectors, concrete slab and profiled steel sheeting. Adequate care is taken in the modelling of the concrete behaviour when creep is taken into account owing to the change in the elastic modulus with respect to time. The finite element analyses indicated that the slip ductility, the strength and the stiffness of the composite member were all reduced with respect to time. The results of this paper will prove useful in the modelling of the overall composite beam behaviour. Further experiments to validate the models presented herein will be conducted and reported at a later stage.

• Computers and Concrete
• /
• 제21권5호
• /
• pp.513-523
• /
• 2018

Time dependent strain due to creep is a significant factor in structural design. Multi-gene genetic programming (MGGP) and artificial neural network (ANN) are used to develop two models for prediction of creep compliance in concrete. The first model was developed by MGGP technique and the second model by hybridized MGGP-ANN. In the MGGP-ANN, the ANN is working in parallel with MGGP to predict errors in MGGP model. A total of 187 experimental data sets that contain 4242 data points are filtered from the NU-ITI database. These data are used in developing the MGGP and MGGP-ANN models. These models contain six input variables which are: average compressive strength at 28 days, relative humidity, volume to surface ratio, cement type, age at start of loading and age at the creep measurement. Practical equation based on MGGP was developed. A parametric study carried out with a group of hypothetical data generated among the range of data used to check the generalization ability of MGGP and MGGP-ANN models. To confirm validity of MGGP and MGGP-ANN models; two creep prediction code models (ACI209 and CEB), two empirical models (B3 and GL 2000) are used to compare their results with NU-ITI database.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표대회 논문집(III)
• /
• pp.603-608
• /
• 1998

This study was performed to examine the effect of time dependent properties on RC columns in subway structures subjected to high filled soil layer. By using Program TCC which is a modified version of CPF for the present purpose, a typical column in subway structure was analyzed. Four different model equations for predicted time dependent concrete properties(ACI, CEB-FIP, Bazant & Panula and Korea Bridge Specification) was employed, and the results were compared. It was found that a relevant creep coefficient is recommended to be 1.0 for designing columns in subway structure, and the sol filling work would be performed at least 3 months later after the concrete casting in order to ensure durability by reducing the negative effect of concrete time dependent properties.

• Steel and Composite Structures
• /
• 제7권3호
• /
• pp.219-240
• /
• 2007

An analytical-numerical procedure has been presented in this paper to take into account the nonlinear effects of concrete cracking and time-dependent effects of creep and shrinkage in the concrete portion of the continuous composite beams under service load. The procedure is analytical at the element level and numerical at the structural level. The cracked span length beam element consisting of uncracked zone in middle and cracked zones near the ends has been proposed to reduce the computational effort. The progressive nature of cracking of concrete has been taken into account by division of the time into a number of time intervals. Closed form expressions for stiffness matrix, load vector, crack lengths and mid-span deflection of the beam element have been presented in order to reduce the computational effort and bookkeeping. The procedure has been validated by comparison with the experimental and analytical results reported elsewhere and with FEM. The procedure can be readily extended for the analysis of composite building frames where saving in computational effort would be very considerable.