• The KIPS Transactions:PartC
• /
• v.9C no.4
• /
• pp.543-550
• /
• 2002

This paper proposes the dynamic slot allocation method for real-time VBR (rt-VBR) services in wireless ATM networks. The proposed method is characterized by a contention-based mechanism of the reservation request, a contention-free polling scheme for transferring the dynamic parameters. The base station scheduler allocates a dynamic parameter minislot to the wireless terminal for transferring the residual lifetime and the number of requesting slots as the dynamic parameters. The scheduling algorithm uses a priority scheme based on the maximum cell transfer delay parameter. Based on the received dynamic parameters, the scheduler allocates the uplink slots to the wireless terminal with the most stringent delay requirement. The simulation results show that the proposed method guarantee the delay constraint of rt-VBR services along with its cell loss rate significantly reduced.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.2
• /
• pp.495-504
• /
• 1996

In this paper, series-fed mirostrip array anteenas with coupling-slots are prposed and their operating characteristics are analyzed based on analyzed based on analytical and experimental results. An accurate analysis method for the slot-coupled feed structure is based on using both circuit coupling between anteenas and full-wave analysis which use travling wave mode and non-traveling wave mode on feed line. The basis functions that used for the numerical analysis bas been determined depending upon the accuracy, convergence properties of the solution, and the computation time:The patch uses 3 EB mode, the slot uses 1PWS mode, and feeders use 5 PWS mode. Series-fed array antennas have been designed, built, and tested in a standing-wave configuration. Using the results of the full-wave analysis, the chebyshev array antennas consisting of 8 elements are designed and fabricated changing the amount excited to each array element by adjusting slot length and by the slot position relative to the feeder. Experiment results show that the series-fed array antenna designed by adjusting the slot position relative to the feeder is superior to that designed by slot length.

• Journal of Information Technology Services
• /
• v.15 no.4
• /
• pp.97-109
• /
• 2016

The rapid deployment of millions of mobile sensors and smart devices has resulted in high demand for opportunistic encounter-based networking. For the cooperative video surveillance of dashboard cameras in nearby vehicles, a fast and energy-efficient asynchronous neighbor discovery protocol is indispensable because a dashboard camera is an energy-hungry device after the vehicle's engine has turned off. In the existing asynchronous neighbor discovery protocols, all nodes always try to discover all neighbors. However, a dashboard camera needs to discover nearby dashboard cameras when an event is detected. In this paper, we propose a fast and energy-efficient asynchronous neighbor discovery protocol, which enables nodes : 1) to have different roles in neighbor discovery, 2) to discover neighbors within a search range, and 3) to report promptly the exact discovery result. The proposed protocol has two modes: periodic wake-up mode and active discovery mode. A node begins with the periodic wake-up mode to be discovered by other nodes, switches to the active discovery mode on receiving a neighbor discovery request, and returns to the periodic wake-up mode when the active discovery mode finishes. In the periodic wake-up mode, a node wakes up at multiples of number ${\alpha}$, where ${\alpha}$ is determined by the node's remaining battery power. In the active discovery mode, a node wakes up for consecutive ${\gamma}$ slots. Then, the node operating in the active discovery mode can discover all neighbors waking up at multiples of ${\beta}$ for ${\beta}{\leq}{\gamma}$ within ${\gamma}$ time slots. Since the proposed protocol assigns one half of the duty cycle to each mode, it consumes equal to or less energy than the existing protocols. A performance comparison shows that the proposed protocol outperforms the existing protocols in terms of discovery latency and energy consumption, where the frequency of neighbor discovery requests by car accidents is not constantly high.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.7 s.172
• /
• pp.62-70
• /
• 2005

The nanoindenter and AFM have been used for nanofabrication, such as nanolithography, nanowriting, and nanopatterning, as well as measurement of mechanical properties and surface topology. Nanoscale indents can be used as cells for molecular electronics and drug delivery, slots for integration into nanodevices, and defects for tailoring the structure and properties. Therefore, it is very important to make indents of desired morphology (shape, size and depth). Indents of different shapes can be obtained by using indenters of different geometries such as a cube comer and conical and spherical tips. The depth and size of indents can be controlled by making indentations at different indentation loads. However, in case of viscoplastic viscoelastic materials such as polymethylmethacrylate (PMMA) the time dependent deformation (TDD) should also be considered. In this study, the effect of process parameters such as loading rate and hold-time at peak load on the indent morphology (maximum penetration depth, elastic recovery, transient creep recovery, residual depth pile-up height) of PMMA were studied for hyperfine pattern fabrication.

• Journal of Internet Computing and Services
• /
• v.10 no.4
• /
• pp.213-222
• /
• 2009

IEEE 802.15.3 HR-WPAN is designed to enable wireless connectivity of high-speed, low-power, low-cost multimedia-capable portable consumer electronic devices. For quality of service, the standard specifies the use of TDMA (Time Division Multiple Access). However, during low contention TDMA gives much lower channel utilization and higher delays than CSMA (Carrier Sensing Multiple Access) because in TDMA, a node can transmit only during its scheduled time slots whereas in CSMA, nodes can transmit at any time as long as there is no contention. By mixing CSMA and TDMA, Hybrid MAC becomes more robust to timing failures, time-varying channel conditions, slot assignment failures and topology changes than a stand-alone TDMA.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.2
• /
• pp.553-556
• /
• 2005

It is analyzed that WAP packet transmission time to improve performance of WAP using SAR algorithm in Bluetooth channel. The order for SAR algorithm to improve the transfer capability, it is fragmented in WTP total messages that are coming down from upper layer and then the packets are sent one at time in baseband. And it is studied that transmission time for WAP over bluetooth according to DM1, DM3 or DM5 packet type using SAR algorithm in Bluetooth piconet environment. This SAR algorithm decreases WAP packet transmission time of L2CAP baseband packets by sending packet which are spanning multiple slots.

• Journal of Aerospace System Engineering
• /
• v.12 no.1
• /
• pp.10-16
• /
• 2018

In 2018 and 2019, GEO-KOMPSAT-2A and GEO-KOMPSAT-2B will be launched in order to succeed the COMS mission. The two satellites will be collocated in $128.25{\pm}0.05$ degrees East. For precise ranging and orbit determination, the GEO-KOMPSAT-2B will be equipped with LRA (Laser Retroreflector Assembly) and SLR (Satellite Laser Ranging) systems will be utilized. This systems are located in Geochang. In this case, the laser beam emitted from the SLR station can cause problems in terms of safety of optical payloads and image quality. As a solution of this possibility, the laser ranging will be done during the night time when the shutters of the optical payloads remain closed. Still, the optical payload of the GEO-KOMPSAT-2A is not safe from the laser beam because its optical payload shall continue its mission for 24 hours a day. In order to handle this problem, the laser ranging shall be limited to time slots when the angular distance between two satellites observed from the Geochang SLR station is large enough. In this paper, through orbit simulations, the characteristics of variation of the angular distance between the two satellites is analyzed to figure out the time slots when laser ranging is allowed.

• Journal of the Institute of Convergence Signal Processing
• /
• v.5 no.1
• /
• pp.73-78
• /
• 2004

There are random, continuous, and periodic allocation methods in the time slot sequence integrity for the multi-slot call. In the T-S-T switch, there are 2 time switch and the 2*2 space switch. Three time-slot allocation methods are suggested for the simulation. In the simulation, the searching times for time-slots on a multi-slot call is chosen to 32, and the simulation time is chosen to 100,000 seconds. Three kinds of calls are supposed for a multi-slot call : one time-slot call, two time-slot call, and 6 time-slot call. In the simulation, the carried traffic and the blocking probability are calculated on the 3 different traffic cases of 8:1:1, 6:2:2, 4:3:3(one time-slot : two time-slot : 6 time-slot) multi slot calls. It is shown that the blocking probability for the periodic time slot allocation method is best. As a result, the periodic time-slot allocation method is the proper one for the multi-slot ATM switch.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.1
• /
• pp.128-133
• /
• 2005

Respond time and processing rate representing how many tasks can be done during an unit time in a client/server environment are generally use for measuring the performance of computers. In this paper, we suggest a window buffer managing scheme based on a window with many of short-term sliced slots where a media stream is allocated and deallocated into them so that it can maximize the utilization ration of the limited buffer on a multimedia server. And we also propose a buffer substitution scheme for reducing I/O times of a multimedia server by counting re-reference time point about a used block and then it can be reused by the next consecutive media stream.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.6
• /
• pp.1120-1129
• /
• 2015

In this paper, we propose an algorithm to detect movement noise in PPG(Photoplethysmography) measurements. Movement noise significantly deteriorate PPG signals in measurement, so that a movement noise detection algorithm is critical before using measured PPG signals for applications such as diagnosis. To detect movement noise, we apply wavelet transform to PPG signals instead of short-time Fourier transform and decide if the measured signlas include movement noise. To that end, we adaptively choose a wavelet, which is the most similar to the subject's PPG pattern. In the case when movement noise is intentionally added in the 20% and 30% of the total experiment time, our algorithm detects time-slots including movement and outperforms previous works.