• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.37 no.3
• /
• pp.197-204
• /
• 2024

In this paper, the structural performance of Suwon Hwaryeongjeon Unhangak, a representative traditional timber structure in the late Joseon Dynasty, was evaluated. Based on the structure composition of Unhangak, an analysis model was elaborately constructed with Midas Gen, a 3-dimensional structural analysis software. The safety and serviceability of major structural members were evaluated by static analysis, and the dynamic behavior characteristics were evaluated by eigenvalue analysis. Most of the members satisfied the safety and serviceability standards with a margin; however, the bending stress ratio in the oemogdori exceeds the standard by 20.7%, so it is considered that long-term monitoring is needed for this member. The natural period of Unhangak is 1.079 seconds, which is slightly longer than traditional timber buildings of similar scale. In particular, it is analyzed that torsional movement occurred in the secondary mode due to the influence of the rear masonry firewall.

• Korean Journal of Heritage: History & Science
• /
• v.47 no.4
• /
• pp.22-47
• /
• 2014

This study was to understand the basic principles of the East Asian wooden structure system research and analysis. The Korea and China ancient architecture internal structure research that the combination of girders and crossbeams position. The ancient wooden structures of eastern Asian countries, Korea and China are not much different from each other in the principles of the wooden architecture structure, combining pillars, purlins and crossbeams. However, it seems that age-division, local-division, national-division differs in detail techniques. China ancient wooden structures combination of purlin and crossbeam, and So-seul Timber(Chinese name: Chashou叉手, Tuojiao 托脚) seems to show differences according to the age of the fulcrum position, detailed approach is also different according to various historical dynasty. Before in the 15th century, Purlin and Crossbeam are coupled to each other, but since the 15th century, seems to have developed a technique combined with each other Girder and Crossbeam and to prevent buckling of the Crossbeam cross-sectional area increased dramatically. For Tuojiao in China Tang-Wudai dynasty(A.D. 618~979), can see that saw the top position Girder and Tuojiao no direct coupling, can be seen as maintaining the safety of the material than the material of the inner wooden structures prevent buckling of the purlin. Korea ancient wooden structures of Goryeo dynasty(A.D. 918~1391), So-seul Timber(Chinese name Tuojiao) why do not to use the fashion? To use Purlin Lower backing material techniques to prevent buckling is a popular trend to stable can be thought of as a preferred way to maintain. I think that with universality beyond the local-division, national-division and the two countries since the 15th century of Korea and China ancient wooden structures detailed mechanism for the purlin buckling. In middle-late Chosen dynasty, The effect of Deotgeolyi- techniques and fleeting beams reduce the purlin buckling that reduces the load transmitted from purlin and crossbeam of how to reduce the load on the roof portion of the architecture fleeting beams used, which of craftsmanship of the Chosen Dynasty building can be referred to as another technique for preventing buckling purlin. This Korea and China ancient architecture purlin beam structure and material So-seul Timber study. Seems to be able to provide a basic research study to restore and designed the old wooden architectures.

• Korean Journal of Heritage: History & Science
• /
• v.47 no.1
• /
• pp.164-179
• /
• 2014

The Buddhas of the Three Words in a form of arranging Bhaiṣajyaguru and $Amit{\bar{a}}bha$ at its side based on ${\acute{S}}{\bar{a}}kyamuni$ at the center is enshrined in Daeungbojeon Hall of Daeheungsa Temple located at Haenam. So far, this Buddhas of the Three Words has been known as a wooden Buddha statue. However, as a result of X-ray screening, in left/right Buddha statues excepting main Buddha, wood and molding clay layer were observed at the same time. Therefore, this study intended to observe its internal structure, grafting method and to clarify making technique of Buddha statue during Joseon era based on image information being obtained through X-ray screening of The Buddhas of the Three Words of Daeheungsa Temple. As its result, it was revealed that form of ${\acute{S}}{\bar{a}}kyamuni$ was completed by mainly grafting 5 pieces of timber and this statue shows a typical wood grafted Buddha statue during Joseon era. Form of Bhaiṣajyaguru and $Amit{\bar{a}}bha$ were completed based on molding technique by applying clay on sculpture similar to its appearance after sculpturing more than 10 pieces of timber through its grafting. In other words, internal timber is considered to play a role of its core and grafting method of timber is more close to a technique of molding Buddha statue than to that of wooden Buddha statue during Joseon era. However, clay was directly applied on timber thinly, not applying clay thickly on it after winding straw rope on wooden core and its characteristic is that its facial area was completely composed of wooden construction only. Therefore, it is hard to rule out a possibility that the original sculpturing intention of an artist might be a wooden Buddha statue but in view of the fact that a word, 'molding' was used in a record of relics buried in statue, it could be seen that this Buddha statue might have been recognized as a molding statue at the time when creation of this statue was completed. It is considered that number of case of making statue based on this technique would be more increased when more results of X-ray screening should be accumulated and if more data should be collected, it would provide a significant evidence for identifying chronological, regional aspects of making technique of Buddha statue.

• KIEAE Journal
• /
• v.13 no.3
• /
• pp.15-20
• /
• 2013

The purpose of this study is to analyze the planning characteristics of passive house by the building structural types in foreign cases. The interests and demands about passive house have been increased, and various building structural types and design methods have been attempted for passive house in Korea. But domestic research results and development experiences about passive house were lack. The results of this study are as follows; First, in terms of energy performance, insulation performance, airtightness, there are not significant differences at the 95% confidence level by the structural types of passive house. Second, in terms of the types of insulation materials, there are significant differences at the 95% confidence level by the structural types of passive house. Third, in principle there is no need of traditional heating facility in passive houses, but in practice traditional heating facilities are used additionally in about half of survey cases for the comfort of occupants.

• International Journal of High-Rise Buildings
• /
• v.11 no.3
• /
• pp.171-180
• /
• 2022

Research and development on high-rise or large-scale wooden buildings have been actively conducted both domestically and internationally. The trend of high-rise wooden buildings is driven by increasing awareness of environmental issues. To utilize wooden materials in buildings is believed to lead to the reduction of the environmental impact. On the other hand, Japan is one of the most earthquake-prone countries in the world, and many wooden detached houses have been damaged in past major earthquakes. This paper summarizes the issues that arise in the realization of medium- and high-rise wooden buildings in Japan, and introduces the initiatives that have been seen so far.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.1
• /
• pp.73-84
• /
• 2018

Recently, the importance of flame retardation treatment technology has been emphasized due to the increase in urban fire accidents and fire damage incidents caused by building exterior materials. Particularly, in the utilization of wood-based building materials, the flame retarding treatment technology is more importantly evaluated. An Intumescent system is one of the non-halogen flame retardant treatment technologies and is a system that realizes flame retardancy through foaming and carbonization layer formation. To apply the Intumescent system, composite material was prepared by using Ethylene vinyl acetate (EVA) as a matrix. To enhance the flame retardant properties of the Intumescent system, a nano-clay was applied together. Composite materials with Intumescent system and nano - clay technology were processed into sheet - like test specimens, and then a new structure of cross laminated timber with improved flame retardant properties was fabricated. In the evaluation of combustion characteristics of composite materials using Intumescent system, it was confirmed that the maximum heat emission was reduced efficiently. Depending on the structure attached to the surface, the CLT had two stages of combustion. Also, it was confirmed that the maximum calorific value decreased significantly during the deep burning process. These characteristics are expected to have a delayed combustion diffusion effect in the combustion process of CLT. In order to improve the performance, the flame retardation treatment technique for the surface veneer and the optimization technique of the application of the composite material are required. It is expected that it will be possible to develop a CLT structure with improved fire characteristics.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.50 no.1
• /
• pp.1-19
• /
• 2022

The Geumgang Pine (Pinus densiflora) Forest in Sogwang-ri, Uljin has traditionally been a pine tree protection area (prohibited forest) for timber production purposes, and is now designated and managed as a protected area for forest genetic resource conservation by the Korea Forest Service. This study, we analyzed topographical characteristics, existing vegetation, tree age, and plant community structure, and proposed a sustainable management method for the Geumgang Pine (Pinus densiflora) Forest in Sogwang-ri, Uljin for timber havesting purposes. The topographical characteristics of the target area were 36.7% ridges and 38.7% valleys; the ratio of ridges to valleys was similar, and the slopes formed 24.7% of the total area. The types of pine forest communities are divided into six types based on the progress of pine forest renewal, the competition with other species such as deciduous broadleaf trees, and the formation of layered structures. It has been confirmed that the age of the large-diameter pine trees (40~60cm in diameter) is approximately 60~70 years, which is relatively low. As a result of the analysis of the relative importance percentage and layered structure, differences depended on the progress of the pine forest renewal project, and not only the maintenance of the pine forest, but also the creation of a secondary growth forest, the density adjustment of pine trees, and the active management of competitive trees. The average basal area by the community was 12,642.1~25,424.4cm² for the tree layer and 1.8~1,956.5cm² for the low tree layer based on a quadrat of 400m². The difference in the basal area appeared to depend on the size and number of trees forming the tree layer and the degree of pine forest renewal (the degree of time elapsed after thinning pine trees). The average number of species that appeared in each community was 8.7-20.3; there were many species located in valleys, and the type competes with deciduous broadleaf trees due to the lack of management. The diversity of species ranged from 0.6915-1.0942, and was evaluated as low compared to pine communities in central temperate zones. In this paper, we determined the management goals of Geumgang Pine (Pinus densiflora) Forest in Sogwang-ri, Uljin to produce timber with high economic value, and suggested efficient vegetation management for continuous afforestation, the establishment of a timber production system, and improvement of wood production as a management direction.

• Journal of Ecology and Environment
• /
• v.29 no.1
• /
• pp.17-22
• /
• 2006

Since the demands not only for value-added timber but the environmental functions of forests had been increased, native tree species has been, and is rapidly being replaced by foreign tree species in many parts of the world. However, the studies on population structure and regeneration characteristics of native tree species were not conducted enough. Regeneration of Kalopanax septemlobus growing among other hardwoods in natural forests is very difficult because of its low seed viability and germination rate. The study examined the distribution of mature trees of K. septemlobus and their regeneration pattern at the 1.12 ha study plot in natural deciduous broad-leaved forest of Mt. Jeombong. The density and mean DBH of K. septemlobus was 97 trees per ha and 32 cm, respectively. The spatial distribution of K. septemlobus showed a random pattern (aggregation index is 0.935) in the 1.12 ha study plot. The age of 90 trees among 99 sample trees of K. septemlobus ranged from 90 to 110 years and represented a single cohort, thus suggesting that K. septemlobus in advance regeneration has regenerated as a result of disturbances such as canopy opening.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.5
• /
• pp.617-632
• /
• 2019

This study aimed to investigate the anatomical structure and fiber quality of four lesser-used wood species namely Benuang (O. sumatrana), Duabanga (D. moluccana), Pisang Merah (H. hellwigii), and Terap (A. odoratissimus). This study evaluated its suitability for raw material in pulp and paper manufacturing. The anatomical structure was observed macro- and microscopically. Macroscopic structures were observed directly to the wood samples, while microscopic characteristics were observed through microtome specimens. Fiber dimension was measured through macerated specimens and fiber quality was analyzed following the Rachman and Siagian's method. Results showed that these four timber species have similarity in the indistinct growth ring, diffuse porous in a radial pattern, rounded solitary vessel outline, 1 to 3 cells of ray width, deposits within the rays, fiber length, and cell wall thickness. Differences were found on vessel diameter, vessel grouping, vessel frequency, tyloses existence, type of axial parenchyma, and ray height. Based on fiber length and its derived values, the wood fibers of all species studied are suitable for pulp and paper manufacturing. They belong to the II quality class. The produced pulp and paper would have good quality, especially in tensile, folding, and tear strength. To promote their utilization, silviculture aspect of these four species has to be well understood.

• Journal of Korean Society of Forest Science
• /
• v.77 no.4
• /
• pp.389-400
• /
• 1988

The recent trend in multiple-use land management planning is using Model I and Model II formulations designed for timber activity scheduling problems. Numerous models hate been developed, with MUSYC(Johnson and Jones, 1979) being the first to incorporate both model structures. Currently the most popular computer program using both Model I and Model II is FORPLAN(Johnson and others, 1986). A Model I formulation requires fewer rows and provides more direct information on what happens to an acre from rotation to rotation. In some problems, Model II provides a much more compact problem matrix with much fewer columns and only a moderate increase in row number. In this paper we examined and evaluated their usefulness in comprehensive multiresource forest management planning.