• Transactions on Electrical and Electronic Materials
• /
• v.16 no.5
• /
• pp.227-233
• /
• 2015

To reduce the cost of solar electricity, the crystalline-silicon (c-Si) photovoltaic industry is moving toward the use of thinner wafers (100 μm to 200 μm) to achieve a high efficiency. In this field, it is imperative to achieve an effective passivation method to reduce the electronic losses at the c-Si interface. In this article, we review the most promising surface passivation schemes that are available for high-efficiency solar cells.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.1.2-1.2
• /
• 2011

With recent advances in materials and products, materials processing experiences new challenges. More particles and polymers in material side and thinner and faster deformations in processing side. It happens in most emergying industries such as manufacturing of batteries, solar cells, multi-layer chips, displays, printed electronics, to list a few. In most cases, they are manufactured by coating or printing process, which is defined as a process in which gas is replaced by liquid on a substrate. In this sense, casting, inkjet printing, and roll-to-roll printing are all included. The printing process consists of three unit processes. As the materials used in the above mentioned applications typically contain a large amount of particles with polymers and solvents, they continuously change microstructures during preparation, flow, and even drying. However, little is known about the flow characteristics of such complex fluids and less is known about how to design and control the process. Therefore, for better control of the process and for better quality of the product, we need to understand the flow characteristics of these complex fluids under extremely fast flow environment.

• Journal of Welding and Joining
• /
• v.16 no.5
• /
• pp.86-92
• /
• 1998

High speed wire seam weldability of tin coated thin gage sheet steels was investigated. Thickness and coating weight ranges of the test materials were 0.21~0.35mm and 1.1/1.1~2.8/11.2g/$m^2$, respectively. Test results indicated that the surface roughness value, Rz decreased as increasing the coating weight. The Rz was thought to be one of the important factors to influence the optimum welding condition range, $\triangle$Q. The $\triangle$Q showed close relationship with welding conditions such as welding pressure and travel speed. Higher welding pressure widened the $\triangle$Q while higher travel speed reduced the $\triangle$Q value. Results also demonstrated that tin coating weight should be optimized based on the weldability or the serviceability after welding. At th HAZ of sheet materials with thinner coating layer, tin depleted zone was produced since molten film of the coating material on the base metal agglomerated by the surface tension, which could result in reducing the corrosion resistance of the HAZ in the service environment.

• Journal of Welding and Joining
• /
• v.13 no.4
• /
• pp.113-121
• /
• 1995

This study deals with the quality and the optimum range of laser cutting process. Cold rolled steel sheets for automobile application were cut by a high power CO$_{2}$ laser system with beam quality of TEM$_{\infty}$ mode. Both process parameters such as travel speed and assist gas pressure, and quality factors were considered to optimize the laser cutting. It was revealed that the thinner the sheet thickness, the less effect of oxidation energy for contributing the cutting process. High speed photographs demonstrated that molten spot on the cut surface moved in a random and vigorous manner according to its viscosity and the flowing direction of assist gas, which resulted in so called striation. Laser cutting produced a very smooth surface of average roughness(Ra) about less than 1.5.mu.m at the optimum range. It was also shown that the characteristics of dross formation was influenced by the flowing durection of assist gas and the fluidity of molten metal drop..

• Current Optics and Photonics
• /
• v.4 no.2
• /
• pp.121-126
• /
• 2020

With the increasing demand for head-mounted display applications, the image quality provided by a near-eye display device is a key factor in satisfying the consumer. Among various techniques to realize a near-eye display that has a thinner volume than the working distance of a human eye, a lightfield image-generation method based on a pinhole array is attracting much attention, with its simple and thin structure. In this paper, we propose a numerical analysis of the visual parameters and verifications with computational reconstruction.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.13 no.1
• /
• pp.87-96
• /
• 1983

Radiographic measurements on the width of mandibular cortical plate and the lamina dura and on the root length were done in 42 patients who were in long-term Dilantin medication. Osteoporosis and root abnormalities were also investigated. The obtained results were as follows: 1. The number of male patients was greater than that of female patients. 2. The width of mandibular cortical plate was thinner in patient group than in control group. 3. There was no significant change in the width of lamina dura between the patient group and control group. 4. The root length of patient group was generally shorter than that of control group. 5. There were evidences of generalized mandibular osteoporosis and alteration in mandibular canal wall in 8 patients. (19%) 6. In Dilantin induced osteomalacia, the radiographic changes of mandibular canal wall and mandibular cortical plate were prominent, but that of lamina dura was not significant.

• Journal of Magnetics
• /
• v.5 no.2
• /
• pp.35-39
• /
• 2000

The correlation between the activation volumes of wall-motion and nucleation processes in Co/Pd multilayers has been investigated. Each activation volume was estimated from the field dependence of the wall-motion speed and the nucleation rate, respectively, based on time-resolved domain patterns grabbed by a MOKE microscope system. Both the activation volumes are changed in the same manner around $0.2\sim1.1\times10^{-17}cm^3$ with changes in the multilayered structure. Interestingly, the correlation between the activation volumes is sensitive to the multilayered structure; the wall-motion activation volume is smaller than the nucleation activation volume for a sample having a smaller number of repeats and a thinner Co-layer thickness, and vice versa. The correlation is closely related with the contrasting reversal modes; the process having the smaller activation volume dominates.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.152-155
• /
• 2004

Effects of sliding speed, applied load, counterpart radius and thickness of PMMA (Poly Methyl Methacrylate) coating layers on their dry sliding frictional and wear behavior were investigated. Sliding wear tests were carried out using a pin-on-disk wear tester. The PMMA layer was coated on Si wafer by a sol-gel technique with two different thicknesses, $1.5{\mu}m\;and\;0.8{\mu}m$. AISI 52100 bearing steel balls were used as a counterpart of the PMMA coating during the wear. Normal applied load and sliding speed were varied. Wear mechanisms were investigated by examining worn surfaces by an SEM. Under most of sliding test conditions, the thicker layer with the thickness of $1.5{\mu}m$ showed lower fiction coefficient than the thinner layer. Effects of sliding speed and counterpart's radius on the frictional behavior were varied depending on the thickness of the coating layer.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.212-213
• /
• 2014

In case of fire spray protection sheath, fire resisting capacity is assessed for each material and installation method according to fire-resistive construction recognition. This study reviews effects of the percentage of water content that exist in fire spray protection sheath during the assess process of fire resisting capacity on fire resisting capacity, and changes of the percentage of water content according to temperature conditions. As a result of exams, as curing temperature is higher and thickness of specimen is thinner, decrease of the percentage of water content becomes significant.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10a
• /
• pp.641-646
• /
• 2000

This paper describes an experimental investigation on the influence of concrete cover thickness on tension stiffening behavior. Total 36 direct tension specimens were tested with variation of cover thickness. Three different concrete compressive strengths were also considered. After cracking, as the cover thickness becomes thinner and the concrete strength becomes higher, tensile stiffness is decreased. Thereby an increase in cover thickness results in increase of the tensile cracking load and tension stiffening effect. Also the increase in concrete strength results in sudden decrease in tension stiffening effect. Hence, the cover thickness and concrete strength are proved to be important factors in tension stiffening behavior.