• Journal of the Korean Vacuum Society
• /
• v.17 no.5
• /
• pp.435-441
• /
• 2008

In this paper, we investigated the electrical properties of triisopropylsilyl (TIPS) pentacene organic thin-film transistor (OTFT) depending on solvent type. We spin coated TIPS pentacene by using chlorobenzene, p-xylene, chloroform, and toluene as solvents. Fabricated OTFT with chlorobenzene shows field-effect mobility of $1.0{\times}10^{-2}cm^2/V{\cdot}s$, on/off ratio of $4.3{\times}10^3$ and threshold voltage of 5.5 V. In contrast, with chloroform, the mobility is $5.8{\times}10^{-7}cm^2/V{\cdot}s$, on/off ratio of $1.1{\times}10^2$ and threshold voltage of 1.7 V. Moreover we measured the grain size of each TIPS pentacene solvent by atomic force microscopy (AFM). From these results, it can be concluded that a solvent with higher boiling point results in better electrical characteristics due to large grain size and high crystallinity of TIPS pentacene layer. In this paper TIPS pentacene with chlorobenzene shows the best electrical properties.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.421-427
• /
• 2009

We successfully fabricated 4.7-inch organic thin film transistors array with $640{\times}480$ pixels on flexible substrate. All the processes were done by photolithography, spin coating and ink-jet printing. The OTFT-Electrophoretic (EP) pixel structure, based on a top gate OTFT, was fabricated. The mobility, ON/OFF ratio, subthreshold swing and threshold voltage of OTFT on flexible substrate are: 0.01 ^2/V-s, 1.3 V/dec, 10E5 and -3.5 V. After laminated the EP media on OTFT array, a panel of 4.7-inch $640{\times}480$ OTFT-EPD was fabricated. All of process temperature in OTFT-EPD is lower than $150^{\circ}C$. The pixel size in our panel is $150{\mu}m{\times}150{\mu}m$, and the aperture ratio is 50 %. The OTFT channel length and width is 20 um and 200um, respectively. We also used OTFT to drive EP media successfully. The operation voltages that are used on the gate bias are -30 V during the row data selection and the gate bias are 0 V during the row data hold time. The data voltages that are used on the source bias are -20 V, 0 V, and 20 V during display media operation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.362-362
• /
• 2014

Atomic layer deposition (ALD) can be regarded as a special variation of the chemical vapor deposition method for reducing film thickness. ALD is based on sequential self-limiting reactions from the gas phase to produce thin films and over-layers in the nanometer scale with perfect conformality and process controllability. These characteristics make ALD an important film deposition technique for nanoelectronics. Tantalum pentoxide ($Ta_2O_5$) has a number of applications in optics and electronics due to its superior properties, such as thermal and chemical stability, high refractive index (>2.0), low absorption in near-UV to IR regions, and high-k. In particular, the dielectric constant of amorphous $Ta_2O_5$ is typically close to 25. Accordingly, $Ta_2O_5$ has been extensively studied in various electronics such as metal oxide semiconductor field-effect transistors (FET), organic FET, dynamic random access memories (RAM), resistance RAM, etc. In this experiment, the variations of chemical and interfacial state during the growth of $Ta_2O_5$ films on the Si substrate by ALD was investigated using in-situ synchrotron radiation photoemission spectroscopy. A newly synthesized liquid precursor $Ta(N^tBu)(dmamp)_2$ Me was used as the metal precursor, with Ar as a purging gas and $H_2O$ as the oxidant source. The core-level spectra of Si 2p, Ta 4f, and O 1s revealed that Ta suboxide and Si dioxide were formed at the initial stages of $Ta_2O_5$ growth. However, the Ta suboxide states almost disappeared as the ALD cycles progressed. Consequently, the $Ta^{5+}$ state, which corresponds with the stoichiometric $Ta_2O_5$, only appeared after 4.0 cycles. Additionally, tantalum silicide was not detected at the interfacial states between $Ta_2O_5$ and Si. The measured valence band offset value between $Ta_2O_5$ and the Si substrate was 3.08 eV after 2.5 cycles.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.spc8
• /
• pp.2899-2905
• /
• 2011

We have demonstrated that TPyPA can be used as an efficient multi-functional material for OLEDs; hole transporting material (HTL), blue and white-light emitter. The device based on TPyPA as the HTL exhibited an external quantum efficiency of 1.7% and a luminance efficiency of 4.2 cd/A; these values are 40% higher than the external quantum efficiency and luminance efficiency of the NPD-based reference device. The device based on TPyPA as a blue-light emitter exhibited an external quantum efficiency of 4.2% and a luminance efficiency of 5.3 $cdA^{-1}$ with CIE coordinates at (0.16, 0.14), the device based on TPyPA as a white-light emitter exhibited an external quantum efficiency of 3.2% and a luminance efficiency of 7.7 $cdA^{-1}$ with CIE coordinates at (0.33, 0.39). Also, TPyPA-based organic solar cell (OSC) exhibited a maximum power conversion efficiency of 0.35%. TPyPA-based organic thin-film transistors (OTFTs) exhibited highly efficient field-effect mobility (${\mu}_{FET}$) of $1.7{\times}10^{-4}cm^2V^{-1}s^{-1}$, a threshold voltage ($V_{th}$) of -15.9 V, and an on/off current ratio of $8.6{\times}10^3$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.10
• /
• pp.34-41
• /
• 2010

We proposed the new pixel compensation circuit with high aperture ratio and the driving method for the large-area, low-power AMOLED applications in this study. We designed with the low-temperature poly-silicon(LTPS) thin film transistors(TFTs) that has poor uniformity but good mobility and stability. To lower the error rate of the pixel circuit and to improve the aperture ratio for bottom emission method, we simplified the pixel compensation circuit. Because the proposed pixel compensation circuit with high aperture ratio has very low contrast ratio for conventional driving methods, we proposed the new driving method and circuit for high contrast ratio. Black data insertion was introduced to improve the characteristics for moving images. The pixel circuit was designed for 19.6" WXGA bottom-emission AMOLED panel, and the average aperture ratio of the pixel circuit is improved from 33.0% to 41.9%. For the TFT's $V_{TH}$ variation of ${\pm}0.2\;V$, the non-uniformity and contrast ratio of the designed panel was estimated under 6% and over 100000:1 respectively.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.3
• /
• pp.7-11
• /
• 2017

In this paper, we have studied the characteristics of NAND Flash memory in SONOS Poly-Si Thin Film Transistor (Poly-Si TFT) device. Source/drain junctions(S/D) of cells were not implanted and selective transistors were located in the end of cells. We found the optimum conditions of process by means of the estimation for the doping concentration of channel and source/drain of selective transistor. As the doping concentration was increased, the channel current was increased and the characteristic of erase was improved. It was believed that the improvement of erase characteristic was probably due to the higher channel potential induced by GIDL current at the abrupt junction. In the condition of process optimum, program windows of threshold voltages were about 2.5V after writing and erasing. In addition, it was obtained that the swing value of poly Si TFT and the reliability by bake were enhanced by increasing process temperature of tunnel oxide.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.263-263
• /
• 2016

최근 반도체 시장에서는 저비용으로 고성능 박막 트랜지스터(TFT)를 제작하기 위한 다양한 기술들이 연구되고 있다. 먼저, 재료적인 측면에서는 비정질 상태에서도 높은 이동도와 가시광선 영역에서 투명한 특성을 가지는 산화물 반도체가 기존의 비정질 실리콘이나 저온 폴리실리콘을 대체하여 차세대 디스플레이의 구동소자용 재료로 많은 주목받고 있다. 또한, 공정적인 측면에서는 기존의 진공장비를 이용하는 PVD나 CVD가 아닌 대기압 상태에서 이루어지는 용액 공정이 저비용 및 대면적화에 유리하고 프리커서의 제조와 박막의 증착이 간단하다는 장점을 가지기 때문에 활발한 연구가 이루어지고 있다. 특히 산화물 반도체 중에서도 indium-gallium-zinc oxide (IGZO)는 비교적 뛰어난 이동도와 안정성을 나타내기 때문에 많은 연구가 진행되고 있지만, 산화물 반도체 기반의 박막 트랜지스터가 가지는 문제점 중의 하나인 문턱전압의 불안정성으로 인하여 상용화에 어려움을 겪고 있다. 따라서, 본 연구에서는 기존의 산화물 반도체의 불안정한 문턱전압의 문제점을 해결하기 위해 마이크로웨이브 열처리를 적용하였다. 또한, 기존의 IGZO에서 suppressor 역할을 하는 값비싼 갈륨(Ga) 대신, 저렴한 지르코늄(Zr)과 하프늄(Hf)을 각각 적용시켜 용액 공정 기반의 Zr-In-Zn-O (ZIZO) 및 Hf-In-Zn-O (HIZO) TFT를 제작하여 시간에 따른 문턱 전압의 변화를 비교 및 분석하였다. TFT 소자는 p-Si 위에 습식산화를 통하여 100 nm 두께의 $SiO_2$가 열적으로 성장된 기판 위에 제작되었다. 표준 RCA 세정을 진행하여 표면의 오염 및 자연 산화막을 제거한 후, Ga, Zr, Hf 각각 suppressor로 사용한 IGZO, ZIZO, HIZO 프리커서를 이용하여 박막을 형성시켰다. 그 후 소스/드레인 전극 형성을 위해 e-beam evaporator를 이용하여 Ti/Al을 5/120 nm의 두께로 증착하였다. 마지막으로, 후속 열처리로써 마이크로웨이브와 퍼니스 열처리를 진행하였다. 그 결과, 기존의 퍼니스 열처리와 비교하여 마이크로웨이브 열처리된 IGZO, ZIZO 및 HIZO 박막 트랜지스터는 모두 뛰어난 안정성을 나타냄을 확인하였다. 결론적으로, 본 연구에서 제안된 마이크로웨이브 열처리된 용액공정 기반의 ZIZO와 HIZO 박막 트랜지스터는 추후 디스플레이 산업에서 IGZO 박막 트랜지스터를 대체할 수 있는 저비용 고성능 트랜지스터로 적용될 것으로 기대된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.267.1-267.1
• /
• 2016

본 연구에서는 nematic 액정의 종류 중 하나인 5CB (4-Cyano-4'-pentylbiphenyl) 물질을 박막 트랜지스터 (TFT)의 passivation 층으로 사용했을 때 그 전기적 특성향상을 확인하였다. RF-magnetron sputtering법으로 증착된 비정질 InGaZnO 박막을 활성층으로 사용한 TFT를 제작하여 그 활성층 위에 drop형식으로 passivation 하였다. 그 결과, drain current (I_DS)가 약 10배 정도 증가하고, linear region(V_D=0.5V)에서 mobility와 subthreshold slope(SS)이 각각 6.7에서 12.2, 0.3에서 0.2로 향상되는 것이 보였다. 이것은 gate bias가 인가되었을 때 freedericksz 전이를 통한 액정의 배향과 이때 형성된 dipole 형성에 의한 것으로 보이며, 이러한 LC의 배향은 편광현미경을 통하여 표면과 수직으로 배향한다는 사실을 확인 할 수 있었고 이 LC-passivation된 a-IGZO TFT의 전기적 특성의 향상에 대한 mechanism을 제시하였다. 그리고 배향한 LC가 가지는 dipole에 의해 bias stress 상황에서 독특한 electron trapping과 recovery의 증폭효과가 나타났다. V_G=+20V의 positive gate bias stress를 1000s동안 가했을 때, passivation되지 않은 a-IGZO TFT의 경우 +4V의 threshold voltage shift(${\Delta}V$_TH)가 발생되었고, 바로 -20V의 negative gate bias를 30s간 가해주었을 때 -2.5V의 ${\Delta}V$_TH가 발생하였다. 반면 LC-passivation된 a-IGZO TFT의 경우 각각 +5V와 -4V의 ${\Delta}V$_TH로 더 큰 변화를 가져왔다. 이러한 LC에 의한 electron trapping/recovery 증폭효과에 대한 model을 제시하였다.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.11
• /
• pp.48-55
• /
• 2016

Ambient-light sensor system, which changes the brightness of a display as ambient light change, was studied to reduce the power consumption of the mobile applications such as note PC, tablet PC and smart phone. The ambient-light sensor system should be integrated on a display panel to improve the complexity and cost of mobile applications, so the ambient-light sensor and readout circuit was integrated on a display panel using low-temperature poly-silicon thin film transistors (LTPS-TFT). We proposed the new compensation method to correct the panel-to-panel variation of the ambient-light sensors, without additional equipment. We designed and investigated the new readout circuit with the proposed compensation method and the analog-to-digital converter for the final digital output of ambient light. The readout circuit has very simple structure and control timing to be integrated with LTPS-TFT, and the input luminance ranges from 10 to 10,000 lux. The readout rate is 100 Hz, and maximum differential non-uniformity with 20 levels of the final output below 0.5 LSB.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.194.1-194.1
• /
• 2015

Transition metal dichalcogenide (TMD) with layered structure, has recently been considered as promising candidate for next-generation flexible electronic and optoelectronic devices because of its superior electrical, optical, and mechanical properties.[1] Scalability of thickness down to a monolayer and van der Waals expitaxial structure without surface dangling bonds (consequently, native oxides) make TMD-based thin film transistors (TFTs) that are immune to the short channel effect (SCE) and provide very high field effect mobility (${\sim}200cm^2/V-sec$ that is comparable to the universal mobility of Si), respectively.[2] In addition, an excellent photo-detector with a wide spectral range from ultraviolet (UV) to close infrared (IR) is achievable with using $WSe_2$, since its energy bandgap varies between 1.2 eV (bulk) and 1.8 eV (monolayer), depending on layer thickness.[3] However, one of the critical issues that hinders the successful integration of $WSe_2$ electronic and optoelectronic devices is the lack of a reliable and controllable doping method. Such a component is essential for inducing a shift in the Fermi level, which subsequently enables wide modulations of its electrical and optical properties. In this work, we demonstrate n-doping method for $WSe_2$ on poly-4-vinylphenol and poly (melamine-co-formaldehyde) (PVP/PMF) insulating layer and adjust the doping level of $WSe_2$ by controlling concentration of PMF in the PVP/PMF layer. We investigated the doping of $WSe_2$ by PVP/PMF layer in terms of electronic and optoelectronic devices using Raman spectroscopy, electrical measurements, and optical measurements.