• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.54-54
• /
• 2008

$Eu^{2+}$, $Nd^{3+}$ co-doped $BaAl_2O_4$ are known as a long afterglow phosphor. We found that $Eu^{2+}$-doped $BaAl_2O_4$ showed ptotoconductivity in the range of UV and visual light. In this study, $BaAl_2O_4$:Eu thin film has been prepared by RF sputtering method and a sensing characteristics to UV and visual light was performed. Only $Eu^{2+}$ and $Nd^{3+}$ co-doped $BaAl_2O_4$ powders and targets for deposition were prepared by a convention solid state method, and the deposition was performed in a reducing $H_2$-Ar mixture gas on Si substrates. The observation of crystalline phase and morphology of the sputtered film were performed using XRD, EDX. The photoluminescence and photocurrent to UV and visual light were measured simultaneously using 300W-Xe solar simulator as a light source. It was confirmed that the photocurrent induced by irradiation of light showed a linear relationship to the light intensity.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.9
• /
• pp.776-780
• /
• 2000

ZnGa$_2$O$_4$thin films were prepared on Si(100) wafer in terms of RF power, substrate temperatures and Ar/O$_2$flow rate by RF Magnetron Sputtering. Photoluminescence(PL) measurement was employed to observe the emission spectra of ZnGa$_2$O$_4$films. The influences of various deposition parameters on the properties of grown films were studied. The optimum substrate deposition temperature for luminous characteristics was about 50$0^{\circ}C$ in this investigation. PL spectrum of ZnGa$_2$O$_4$ thin films showed broad band luminescence spectrum.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.316-319
• /
• 2000

By RF magnetron sputtering ZnGa$_2$O$_4$thin films were prepared on Si(100) wafer in terms of RF power, substrate temperatures and Ar/O$_2$flow rate. Crystallographic orientation was characterized by x-ray diffraction(XRD). Surface morphology and microstructure were observed by scanning electron microscope(SEM). Photoluminescence(PL) measurement was employed to observe the emission spectra of ZnGa$_2$O$_4$films. The influences of various deposition parameters on the properties of grown films were studied. PL spectrum of ZnGa$_2$O$_4$thin films showed broad band luminescence spectrum.

• Proceedings of the Optical Society of Korea Conference
• /
• 2002.11a
• /
• pp.20-21
• /
• 2002

• Journal of Sensor Science and Technology
• /
• v.8 no.1
• /
• pp.10-15
• /
• 1999

White emission thin film electroluminescent device was fabricated using ZnS for phosphor layer and BST ferroelectric thin film for insulating layer. For fabrication conditions of BST thin film, stoichiometry of target was $Ba_{0.5}Sr_{0.5}TiO_3$, substrate temperature was $400^{\circ}C$, working pressure was 30 mTorr, and A:$O_2$ ratio was 9:1. At this time, dielectric constant was 209 at 1kHz frequency. For phosphor layer ZnS:Mn, ZnS:Tb, and ZnS:Ag were used. Mixing rates of activators were respectively 0.8, 0.8, and 1 wt%. Total thickness of phosphor tapers was 500 nm, thickness of lower insulating layer was 200 nm, and thickness of upper insulating layer was 400 nm. In this conditions, luminescence threshold voltage of thin film electroluminescent device was $95\;V_{rms}$, maximum brightness was $3,000\;cd/m^2$ at $150\;V_{rms}$. Luminescence spectrum peak was observed at region of blue(450 nm), green(550 nm), and red(600 nm).

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1629-1631
• /
• 2007

Significant process in the performance and commercialization of full-color thin-film electroluminescent(EL) displays has been achieved. This is due to the remarkable progress made in the performance of exiting EL phosphors, development of new phosphor materials, and design of new EL phosphor structures. In this paper, we fabricated thinfilm EL devices with ZnS buffer and $BaTiO_3$ electric layer with on top and bottom of phosphor layer. The effect of ZnS and $BaTiO_3$ layer on the luminance of EL device were studied.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.2
• /
• pp.27-37
• /
• 1997

Photoluminescent and cathodoluminescent charcteristics of inorganic luminescent materials were investigated ot develop possible phosphors for thin film electroluminescent (TFEL) device applications. Mg, Zn, and Photoluminescent and cathodoluminescent charcteristics of inorganic luminescent materials were investigated ot develop possible phosphors for thin film electroluminescent (TFEL) device applications. Mg, Zn, and $Si_3N_4$ powders were used to synthesize $(Mg_xZn_{1-x})SiN_2$ host materials. $Tb_4O_7$ and $Eu_2O_3$ powdrs were added as luminescent centers. Very sharp emission spectra of $Tb^{3+}$ ions were observed from $Mg._5Zn._5SiN_2:Tb$ sampels sintered at $1400^{\circ}C$ for an hour and the maximum intensity of emission spectra occured at wavelength of 550nm (green light). Synthetic conditions of $(Mg_xZn_{1-x})SiN_2:Eu$ phosphors were optimized for the hghest luminescence. The Eu concentrations were varied from 0.2% to 1.6%. Before firing, the powders were mixed using ballmills, methanol, acetone, or D.I. water. The Mg/Zn ratio also were varied from x=0.3 to x=0.7. The maximum PL intensity was obtained from a sample with 1.2% Eu concentration and the powder was mixed with methanol and dried before firing. The maximum intensity of the emission spectra occurred t the wavelength of 470nm(blue light). TFEL devices fabricated by using sputter deposition of $(Mg._3Zn._7)SiN_2:Eu$ phosphor layer showed yellowish white emission at the phosphor field of 2MV/cm.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.1
• /
• pp.112-117
• /
• 2004

$Y_2$$_{-x}$G $d_{x}$ $O_3$:E $u^{3+}$(x=0.0, 0.3, 0.6, 1.0, 1.4) luminescent thin films have been grown on Si (100) substrates using pulsed laser deposition. The films grown under different deposition conditions have been characterized using microstructural and luminescent measurements. The crystallinity, the surface morphology and photoluminescence (PL) of the films are highly dependent on the amount of Gd. The photoluminescence (PL) brightness data obtained from $Y_2$$_{-x}$G $d_{x}$ $O_3$:E $u^{3+}$ films grown under optimized conditions have indicated that Si (100) is one of promised substrates for the growth of high quality $Y_2$$_{-x}$G $d_{x}$ $O_3$:E $u^{3+}$ thin film red phosphor. In particular, the incorporation of Gd into $Y_2$ $O_3$ lattice could induce a remarkable increase of PL. The highest emission intensity was observed with $Y_{1.35}$G $d_{0.60}$ $O_3$: $E^{3+}$, whose brightness was increased by a factor of 1.95 in comparison with that of $Y_2$ $O_3$:E $u^{3+}$ films.3+/ films.films.lms.

• Journal of Biomedical Engineering Research
• /
• v.28 no.2
• /
• pp.306-309
• /
• 2007

PXLM(Phosphor based x-ray light modulator) has a combined structure by phosphor, photoconductor, and liquid crystal and it can realize x-ray image of high resolution in clinical diagnosis area. In this study, we fabricated a photoconductor and investigated electrical and optical properties to confirm application possibility of radiator detector of PXLM structure. As photoconductor, amorphous selenium(a-Se), which is used most in DR(Digital radiography) of direct conversion method, was used and for formation of thin film, it was formed as $20{\mu}m-thick$ by using thermal vacuum evaporation system. For a produced a-Se film, through XRD(X-ray diffraction) and SEM(Scanning electron microscope), we investigated that amorphous structure was uniformly established and through optical measurement, for visible light of 40 $0\sim630nm$, it had absorption efficiency of 95 % and more. After fabricated a-Se film on the top of ITP substrate, hybrid structure was manufactured through forming $Gd_2O_3:Eu$ phosphor of $270{\mu}m-thick$ on the bottom of the substrate. As the result to confirm electrical property of the manufactured hybrid structure, in the case of appling $10V/{\mu}m$, leakage current of $2.5nA/cm^2$ and x-ray sensitivity of $7.31nC/cm^2/mR$ were investigated. Finally, we manufactured PXLM structure combined with hybrid structure and liquid crystal cell of TN(Twisted nematic) mode and then, investigated T-V(Transmission vs. voltage) curve of external light source for induced x-ray energy. PXLM structure showed a similar optical response with T-V curve that common TN mode liquid crystal cell showed according to electric field increase and in appling $50\sim100V$, it showed linear transmission efficiency of $12\sim18%$. This result suggested an application possibility of PXLM structure as radiation detector.

• Journal of the Korean institute of surface engineering
• /
• v.56 no.3
• /
• pp.201-207
• /
• 2023

Eu³⁺-doped SnO² (SnO²:Eu³⁺) phosphor thin films were grown on quartz substrates by radio-frequency magnetron sputtering. The deposition temperature was varied from 100 to 400 ℃. The X-ray diffraction patterns showed that all the thin films had two mixed phases of SnO₂ and Eu₂Sn₂O₇. The 880 nmthick SnO²:Eu³⁺ thin film grown at 100 ℃ exhibited numerous pebble-shaped particles. The excitation spectra of SnO²:Eu³⁺ thin films consisted of a strong and broad peak at 312 nm in the vicinity from 250 to 350 nm owing to the O^2--Eu3+ charge transfer band, irrespective of deposition temperature. Upon 312 nm excitation, the SnO²:Eu³⁺ thin films showed a main emission peak at 592 nm arising from the ⁵D₀→⁷F₁ transition and a weak 615 nm red band originating from the ⁵D₀→⁷F₂ transition of Eu³⁺. As the deposition temperature increased, the emission intensities of two bands increased rapidly, approached a maximum at 100 ℃, and then decreased slowly at 400 ℃. The thin film deposited at 200 ℃ exhibited a band gap energy of 3.81 eV and an average transmittance of 73.7% in the wavelength range of 500-1100 nm. These results indicate that the luminescent intensity of SnO²:Eu³⁺ thin films can be controlled by changing the deposition temperature.