• Journal of Welding and Joining
• /
• v.9 no.4
• /
• pp.60-68
• /
• 1991

The weld quality of end cap welds in Pressurized Heavy Water Reactor (PHWR) Fuel is extremely important for the fuel performance in the nuclear reactor. The quality of resistance upset welds is currently evaluated mainly by the metallographic examination although it reveals only two weld cross-sections in a circumference welds. This investigation was, firstly, carried out to determine whether the ultrasonic examination would be applied to detect weld defects in the end cap welds and, secondly, to measure the mechanical strength of upset butt welds as a function of phase shift percentage. The major results obtained in this study are as follows: 1. The weld current and amount of upset shrinkage linearly increased with increasing the phase shift percentage. 2. Above the phase shift 55%, the defects in the welds were completely eliminated with increasing the phase of sound weld was over the thickness of cladding tube. 3. The ultrasonic testing well detected such defects in the end cap welds as upset external crack, upset split, corner crack and irregular weld flash comparing with the results of metallography. 4. The micro-fissure in the corner of the end cap welds was reliably detected by ultrasonic testing. 5. The mechanical strength in the welds increased with increasing phase shift percentage but the fracture did't occur in the welds above 55%.

• Journal of the Korean Home Economics Association
• /
• v.23 no.3
• /
• pp.9-16
• /
• 1985

There are two standards for evaluation of fabric aesthetics, the feeling of fabric and the fabric sense of sight. Its drapalility with lustre is one of factors to decide the fabric sense of sight. This study was carried out to investigate the drape property property of fabrics. The fabric characteristics and the physisical properties of fabrics were tested. And the effect of the laundering on the drape properties was examined. RESULTS : 1. The drape coefficients of sampled fabrics were increasd as the thickness of fabrics were increased, excluding the fabric consisting of 60% polyester$\times$40% wool. 2. The drape coefficient of sampled fabrics were decreased as the cover faders of fabrics were increased, excluding the summer clothes and the fabrics of 100% wool. 3. The drape coefficients of fabrics other than sumer clothes were increased as the weight of fabrics were in creased. 4. Positive correlation was observed between the stiffness and the drape coefficient. 5. Negative correlation was observed between the fabric shrinkage and the drape coefficient. 6. The drape coefficient was decreased to a certain limit by laundering.But as the laundering was repeated up to certain number, the drape coefficient and the node number, a significant correlation was observed between the drape coefficient and the node shape.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.27 no.4
• /
• pp.675-681
• /
• 1998

Low density polyethlene(LDPE0 films of 50${\mu}{\textrm}{m}$ thickness were fabricated with addition of antimicrobial agents of Rheum palmatum extract, Coptis chinensis extract, sorbic acid and Ag-substitude inorganic zirconium matrix in 1% concentration. The films were compared in physical properties, tested in antimicrobial activity against some selected microorganisms on the agar plate medium and then applied for packaging fresh curled lettuce and cucumber to preserve their qualities. The films with Rheum palmatum extract, Coptis chinensis extract, and Ag-substituted inorganic zirconium matrix did not show any antimicrobial activity on the disk test against Escherichia coli, Staphylococcus aureus, Leuconostoc mesenteroides, Saccharomyces cerevisiae, Aspergillus niger, Aspergillus oryzae, Penicilluium chrysogenum, while film with sorbic acid did against E. coli, S. aureus and L. mesenteroides. The added antimicrobial agents changed the color and light transmittance of the films, but did not affect their mechanical tensile strength, heat shrinkage and wettability. For the packaged curled lettuce and cucumber stored at 5$^{\circ}C$ and 1$0^{\circ}C$, all the LDPE films impregnated with antimicrobial agents showed the reduced growth of total aerobic bacteria in the vegetables compared with control film without any additive until it reached the level around 108/g. They did not give any negative effect on other quality attributes during storage.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.2
• /
• pp.38-45
• /
• 2016

Since a 5-axis machine tool has two rotary axes, it offers numerous advantages, such as flexible accessibility, longer tool life, better surface finish, and more accuracy. Moreover, it can conduct whole machining by rotating the rotary feed axes while setting the fixture at once without re-fixing in contrast to conventional 3-axis machining. However, it is difficult to produce complicated products that have a hollow shape. In contrast, 3D printing can produce an object with a complicated hollow shape easily and rapidly. However, because of layer thickness and shrinkage, its surface finish and dimensional accuracy are not adequate. Therefore, this study proposes hybrid technology by integrating the advantages of these two manufacturing processes. 3D printing was used as the additive manufacturing rapidly in the whole body, and 5-axis machining was used as the subtractive manufacturing accurately in the joining and driving places. The reliability of the proposed technology was verified through a comparison with conventional technology in the aspects of processing time, surface roughness. and dimensional accuracy.

• Journal of the Korean Society for Railway
• /
• v.7 no.4
• /
• pp.312-318
• /
• 2004

The wall in a subway structure is easily subject to crack occurrence since its expansion and shrinkage associated with hydration heat reaction is constrained by the slab. The greater problem is that the crack in the wall may be developed to pass through thickness and eventually deteriorate the structure due to rusting of reinforced steel. Thus, this study aims at controlling thermal cracks as much as possible and determining an optimized size of concrete placement through hydration heat analysis. For this study, effects of placement height, length, temperature and types of cement on the thermal cracks were evaluated by temperature rise, thermal stress and crack index. As results of parametric study, it was found that placement height and length do not have an effect on the temperature rise but have significant one on thermal stress which relates to direct possibility of thermal crack occurrence. This means that proper selection of size balancing internal constraint with external one is much more important than reducing the placement height and length simply. In order to prevent from thermal cracks most effectively, in addition, it was noted to reduce placement temperature and to use the cement blended with mineral admixture.

• Conservation Science in Museum
• /
• v.11
• /
• pp.49-52
• /
• 2010

A wooden Comb excavated at Shinchang-dong wetland site was treated with cetylalcohol as a reinforcing agent. The conservation process was done by freeze drying the wooden artifact after substituting it with no.3 butyl alcohol and impregnating with 40wt% cetylalcohol solution. Consequently there was no noticeable surface damage. Also it showed 54% of remaining weight and a shrinkage of length 3.3%, width 2.1% and thickness 3.1%. Therefore using cetylalcohol for conservation of waterlogged archeological wood was effective dimensional stability and remaining weight.

• Journal of Ocean Engineering and Technology
• /
• v.22 no.1
• /
• pp.64-69
• /
• 2008

As it has been well appreciated from the viewpoint of efficiency, The weld-induced deformation control is one of the most important issues in marine structure production. In the case of thin plate block, weld-induced deformation is more serious than in the case of relatively thick plate block. The heat affect zone of thin plates is wider than that of thick plates with the same heat input. Among weld-induced deformations, the buckling deformation by the shrinkage and residual stress in the weld line direction is one of the most serious deformation types. This paper is concerned with controlling buckling deformations for the thin plate fillet welds, by using the tensioning method. A numerical analysis was carried out to illustrate several dominant buckling modes due to compressive residual stress in the fillet weldsof thin plates. Then, weld tests were carried out for 20 specimens with varying plate thickness, and with different magnitudes and directions for the tension load. The results graphically represented to shaw the effect of the tensioning method in reducing the weld-induced deformation. From the present findings, it was seen that the tensioning method is a useful way to control weld-induced deformations in the fillet welds of thin plates.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.10 no.2
• /
• pp.141-152
• /
• 2018

The heating process such as line heating, triangular heating and so on is widely used in plate forming of shell plates found in bow and stern area of outer shell in a ship. Local shrinkage during heating process is main physical phenomenon used in plate forming process. As it is well appreciated, the heated plate undergoes the change in material and mechanical properties around heated area due to the harsh thermal process. It is, therefore, important to investigate the changes of physical and mechanical properties due to heating process in order to use them plate the design stage of shell plates. This study is concerned with the development of formula of plastic hardening constitutive equation for steel plate on which line heating is applied. In this study the stress correction formula for the heated plate has been developed based on the numerical simulation of tension test with varying plate thickness and heating speed through the regression analysis of multiple variable case. It has been seen the developed formula shows very good agreement with results of numerical simulation. This paper ends with usefulness of the present formula in examining the structural characteristic of ship's hull.

• Steel and Composite Structures
• /
• v.39 no.3
• /
• pp.307-318
• /
• 2021

Utilizing fibers is an effective way to avoid the brittle behavior of the conventional concrete and can enhance its ductility. In particular, propylene fibers can improve concrete properties, including energy absorption, physical and mechanical properties, controlling shrinkage cracks. The increase of fiber density leads to an increase of the overlapping surface of the fiber of concrete and, in turn, a decrease of cracks developed in the concrete. However, the workability of fiber reinforced concrete tends to be lower than the conventional concrete owing mainly to the hairline thickness and excessive concentration of fibers. The low slump of concrete impedes the construction of reinforced concrete members. In this research, we study if the utilization of magnetic water can alleviate the workability issue of young fiber reinforced concrete. To this end, the compressive and flexural strength of four types of concrete (conventional concrete, fiber reinforced concrete, magnetic concrete, magnetic fiber-reinforced concrete) is studied and compared at three different ages of 7, 14, and 28 days. In order to study the influence of the fiber density and length, a study on specimens with three different fiber density (1, 2, 5 kg of fiber in each cubic meter of concrete) and fiber length (6, 12, 18 mm) is undertaken. The result shows the magnetic fiber concrete can result in an increase of the flexural and compressive strength of concrete at higher ages.

• Journal of Periodontal and Implant Science
• /
• v.50 no.6
• /
• pp.406-417
• /
• 2020

Purpose: This study investigated whether the placement of ribose cross-linked collagen (RCLC) membranes without primary soft tissue closure predictably resulted in sufficient alveolar ridge preservation in contained and non-contained extraction sockets. Methods: Membranes were positioned across extraction sockets, undermining full-thickness flaps, and the gingival margins were fixed by double-interrupted sutures without crossed horizontal mattress sutures for 1 week. In non-contained sockets, a bone substitute was used to support the membrane within the bony envelope. Radiographs and clinical images obtained 4 months later were analyzed by ImageJ software using non-parametric tests. Results: In 18 patients, 20 extraction sockets healed uneventfully and all sites received standard-diameter implants (4.1, 4.8, or 5.0 mm) without additional bone augmentation. Soft tissues and the muco-gingival border were well maintained. A retrospective analysis of X-rays and clinical photographs showed non-significant shrinkage in the vertical and horizontal dimensions (P=0.575 and P=0.444, respectively). The new bone contained vital bone cells embedded in mineralized tissues. Conclusions: Within the limitations of this pilot study, open healing of RCLC membranes may result in sufficient bone volume for implant placement without additional bone augmentation in contained and non-contained extraction sockets.