• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.12 no.6
• /
• pp.299-303
• /
• 2002

The relationship of crystallinity between defects distribution with (100) ZnTe/GaAs using HWE growth was investigated by four crystal rocking curve (FCRC) and transmission electron microscopy (TEM). The thickness dependence of crystal quality in ZnTe epilayer was evaluated. The FWHM value shows a strong dependence on ZnTe epilayer thickness. For the films thinner than 6 ${\mu}{\textrm}{m}$, the FWHM value decreases very steeply as the thickness increases. For the films thicker than 6 ${\mu}{\textrm}{m}$, it becomes an almost constant value. At the thickness of 12 $\mu\textrm{m}$ with the smallest value of 66 arcsec. which is the best value so far reported on ZnTe epilayers was obtained. Investigation into the nature and behavior of dislocations with film thickness in (100) ZnTe/(100)GaAs heterostructures grown by Hot Wall Epitaxy (HWE). This film defects range from interface to 0.7 ${\mu}{\textrm}{m}$ thickness was high density, due to the large lattice mismatch and thermal expansion coefficients. The thickness of 0.7~1.8 ${\mu}{\textrm}{m}$ was exists low defect density. In the thicker range than 1.8 ${\mu}{\textrm}{m}$ thickness was measured hardly defects.

• The korean journal of orthodontics
• /
• v.51 no.2
• /
• pp.135-141
• /
• 2021

Objective: To assess the effects of thermoforming on aligner thickness and gap width in six aligner systems with the same nominal thickness. Methods: Six passive upper aligners of different brands were adapted to a single printed cast. Each sample was evaluated with high-resolution micro-computed tomography. To investigate aligner thickness and gap width, two-dimensional (2D) analysis was conducted assessing the effects of the following variables: tooth type (central incisor, canine, and first molar), 2D reference points, and aligner type. Data were analyzed and compared using analysis of variance and Tukey's post-hoc tests (p < 0.05). Results: Tooth type, dental region, and aligner type affected both the gap width and aligner thickness. The aligner thickness remained moderately stable across the arch only in the F22. Conclusions: All thermoformed samples displayed smaller aligner thickness and gap width at anterior teeth and both gingival and coronal centers than at posterior teeth and occlusal surfaces.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.487-490
• /
• 2004

In order to simulate OLED evaporation process, modeling of directional distribution of the vaporized organic materials, film thickness distribution profile and pattern-mask shadow effect are required In accordance with many literatures; all of them except shadow effect modeling are studied and developed. In this paper, modeling algorithm of evaporation shadow is presented for process simulation of full-color OLED evaporating system. In OLED evaporating process the offset position of the point cell-source against the substrate rotation axis and the usage of the patterned mask are the principal causes for evaporation shadow. For geometric simulation of shadow using z-map, the film thickness profile, which is condensed on a glass substrate, is converted to the z-map data. In practical evaporation process, the glass substrate is rotated. This physical fact is solved and modeled mathematically for z-map simulation. After simulating the evaporation process, the z-map data can present the shadow-effected film thickness profile. Z-map is an efficient method in that the cross-sectional presentations of the film thickness profile and thickness distribution evaluation are easily and rapidly achieved.

• Journal of The Korean Digital Architecture Interior Association
• /
• v.11 no.2
• /
• pp.31-39
• /
• 2011

Concrete-filled steel tube(CFT) columns have become popular for building construction due to not only composite effect of steel tube and infilled concrete, but also more economical. The purpose of this paper is to propose the applicable boundary formula of width-to-thickness ratio for rectangular steel tube as using CFT column. A parametric study was performed taking width-to-thickness ratio of rectangular steel tube and compressive strength of concrete as the main parameter. The strength of concrete are selected to 30, 60, 90MPa. The non-linear analysis was adopted in order to take into account the effect of concrete strength. Finally, from the test and analysis results, the effect of increasing strength according to concrete strength and width-to-thickness of steel tube and plastic behavior of specimens were verified distinctly.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.567-571
• /
• 1997

Recently, automobile industry has led to increasing use of aluminum alloy for weight reduction. Automobile made of aluminum alloy can be given lighter, stronger and a harder surface by anodizing than one made of steel-alloy. In this paper, we investigate the influence of lap length, adherend thickness and adhesive thickness on adhesive strength of single-lap adhesive joints by conducting tensile-shear tests. Single-lap adhesive joints of aluminum was calculated using joint factor by using adhesive length, adherend thickness of specimen.

• The Journal of the Korea Contents Association
• /
• v.14 no.4
• /
• pp.249-255
• /
• 2014

Total body irradiation use one of the pre-treatment as hematopoietic stem cell transplantation in the treatment of leukemia. According to the study of Korean network for organ sharing 2013 report, continue to increase the number of hematopoietic stem cell transplantation. however, the current dose evaluation fall short before treatment. So purpose of this study is Surface dose and deep organ dose evaluation and then find the most ideal conditions when change of the thickness on tissue compensator in TBI. Result, surface dose in 4 MV, SSD 280 cm, compensators thickness 0.5 cm, was measured the highest dose 5.84 mGy/min. And the ideal dose showed when compensator thickness less than 1 cm.

• Imaging Science in Dentistry
• /
• v.43 no.3
• /
• pp.135-143
• /
• 2013

Purpose: This study was performed to obtain a quantitative evaluation of the cortical and cancellous bone graft harvestable from the mental and canine regions, and to evaluate the cortical vestibular thickness. Materials and Methods: This study collected cone-beam computed tomographic (CBCT) images of 100 Italian patients. The limits of the mental region were established: 5 mm in front of the medial margin of each mental foramen, 5 mm under the apex of each tooth present, and above the inferior mandibular cortex. Cortical and cancellous bone volumes were evaluated using SimPlant software (SimPlant 3-D Pro, Materialize, Leuven, Belgium) tools. In addition, the cortical vestibular thickness (minimal and maximal values) was evaluated in 3 cross-sections corresponding to the right canine tooth (3R), the median section (M), and the left canine tooth (3L). Results: The cortical volume was $0.71{\pm}0.23mL$ (0.27-1.96 mL) and the cancellous volume was $2.16{\pm}0.76mL$ (0.86-6.28 mL). The minimal cortical vestibular thickness was $1.54{\pm}0.41mm$ (0.61-3.25 mm), and the maximal cortical vestibular thickness was $3.14{\pm}0.75mm$ (1.01-5.83 mm). Conclusion: The use of the imaging software allowed a patient-specific assessment of mental and canine region bone availability. The proposed evaluation method might help the surgeon in the selection of the donor site by the comparison between bone availability in the donor site and the reconstructive exigency of the recipient site.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.32 no.2 s.57
• /
• pp.123-127
• /
• 2006

In this study, we evaluated the crow's fret of 95 Korean female by using mechanical assessments; Skin-Visiometer SV 600 and Dermascan C. Transparency profilometry (Skin Visiometer) were using a very thin skin print which allowed parallel light to pass through and was analysed immediately after production. High-frequency (20 MHz) ultrasonography (Dermascan C) enabled non-invasive evaluation in skin thickness and echodensity. We found a correlation between skin roughness and dermal density. Particularly, we showed a significant correlation between skin roughness (R2) and dermal thickness. Also, we demostrated a significant negative correlation between dermal density and dermal thickness (p < 0.05). Therefore, the ultrasonography system might be considered a very useful method in wrinkle evaluation with the transparency profilometry. Further study will be required.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.19 no.5
• /
• pp.356-362
• /
• 1999

Based on the assumption that film density increases exponentially with exposure in the industrial radiographic film. an equation representing the characteristic curves of industrial radiographic films and a new density-thickness relation are suggested. The accuracy and reliability of the suggested relation has been tested using radiographs of a carbon steel step wedge with known thickness variation by polychromatic X-ray and ${\gamma}$-ray ($Ir^{192}$). The experimental results were well agreed to the proposed relation in the range of film densities from 1.0 to 3.5 and it was more accurate than the conventional relation. It is also found that ${\gamma}$-ray is more effective in this purpose than polychromatic X-ray, which results in variation of effective linear absorption coefficient due to beam hardening effect as thickness increases. Therefore using the equation and experimentally determined parameters the quantitative evaluation of thickness variation is possible and it can be used to evaluate the depth of local corrosion of pressure vessels in plants.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.1
• /
• pp.63-69
• /
• 1992

Plane-strain fatigue crack growth behavior of 7075-76 aluminium alloy was investigated by using side-grooved through-thickness center cracked tension(CCT) specimens. The effect of side-groove on the stress intensity factor value was examined. The effective thickness expression of $B_{e}$= $B_{o}$-( $B_{o}$-( $B_{ o-B_{n}^{2}}$ $B_{o}$ is the most appropriate to evaluate the stress intensity factor of side-grooved CCT specimen for fatigue testing. Fatigue crack growth rates can be well described by the effective stress intensity factor range based on closure measurements, for both side-grooved and uniform thickness specimens. Provided that the thickness of specimen meets the requirements for valid plane-strain fracture toughness, uniform thickness specimen data may be assumed to approximately represent the plane strain through-thickness crack growth behavior.ehavior.r.