• Journal of Oral Medicine and Pain
• /
• v.30 no.4
• /
• pp.401-410
• /
• 2005

The purpose of this study was to assess the effect of heat therapy on cutaneous blood flow and skin temperature at pre-auricular region. Moist heat therapy and ultrasound therapy were applied to 20 healthy subjects(male: 10, female: 10). Cutaneous blood flow and skin temperature before and after heat therapy were measured with laser doppler flowmetry and thermocouple. The results were as follows ; 1. Cutaneous blood flow and skin temperature were significantly increased after moist heat therapy and ultrasound therapy. 2. In application of moist heat therapy, cutaneous blood flow and skin temperature were more increased and maintained longer than in ultrasound therapy. 3. Before heat therapy, cutaneous blood flow and skin temperature were higher in male. 4. There was no significant gender difference in changes of cutaneous blood flow and skin temperature after heat therapy. In conclusion, both moist heat therapy and ultrasound therapy increased cutaneous blood flow and skin temperature significantly, and moist heat therapy was more effective to increase cutaneous blood flow and skin temperature and to maintain increased cutaneous blood flow and skin temperature. There was no significant gender difference in the effect of heat therapy on cutaneous blood flow and skin temperature.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.5 no.4
• /
• pp.309-322
• /
• 2007

This study deals with the irradiation effects on some selected components which are being used in an Advanced Spent Fuel Conditioning Process (ACP). Irradiation test components have a higher priority from the aspect of their reliability because their degradation or failure is able to critically affect the performance of an ACP equipment. Components that we chose for the irradiation tests were the AC servo motor, potentiometer, thermocouples, accelerometer and CCD camera. ACP facility has a number of AC servo motors to move the joints of a manipulator and to operate process equipment. Potentiometers are used for a measurement of several joint angles in a manipulator. Thermocouples are used for a temperature measurement in an electrolytic reduction reactor, a vol-oxidation reactor and a molten salt transfer line. An accelerometer is installed in a slitting machine to forecast an incipient failure during a slitting process. A small CCD camera is used for an in-situ vision monitoring between ACP campaigns. We made use of a gamma-irradiation facility with cobalt-60 source for an irradiation test on the above components because gamma rays from among various radioactive rays are the most significant for electric, electronic and robotic components. Irradiation tests were carried out for enough long time for total doses to be over expected threshold values. Other components except the CCD camera showed a very high radiation hardening characteristic. Characteristic changes at different total doses were investigated and threshold values to warrant at least their performance without a deterioration were evaluated as a result of the irradiation tests.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.17 no.4
• /
• pp.306-312
• /
• 1984

In the present study, in succession to the previous reports, the sterilizing values ($F_0$) of the thermal processes for the canned minced hen-clams in brine and the canned smoked baby-clams in oil were determined ana discussed. The heat penetration tests were carried out three times with three cans at a time for each canned product. The thermocouple was setted on the can so as the tip of the applicaotor fixed on the position a little below the geometrical center of the can. The test cans were placed in the middle layer of the crate in which the same canned products were loaded with, and test cans were arranged to the front, the middle and the rear in the retort. The heat penetration curve obtained for the canned minced hen-clams in brine showed a broken logarithmic heating curve, while that of the canned smoked baby-clams in oil showed a simple logarithmic heating curve. The calculated $F_0$ values for the canned minced hen-clams in brine were 47.79 for No. 2 can, 52.99 for Ne. 7 can. and 45.21 for No. 2 tuna can, respectively. And the $F_0$ value for th canned baby-clams in oil packed into No. 3B square can was 14.12. Additionally, the nomographs represent the relationship between $F_0$ vlaues and B values (process time including $42\%$ of come-up time) for the each canned product were constructed.

• Journal of the Korean Institute of Gas
• /
• v.24 no.5
• /
• pp.29-38
• /
• 2020

It is practically difficult to accurately measure the temperature and concentration of a large combustion systems at industrial sites in real time. Temperature measurement using thermocouple, which are mainly used, is a point-measuring method that is less accurate and less reliable to analyze the wide area range of inner combustion system, and has limitations to internal accessibility. In terms of concentration analysis, most measurement methods use sampling method, which are limited by the difficulty of real-time measurement. As a way to overcome these limitations, laser-based measurement methods have been developed continuously. Laser-based measurement are line-average measurement methods with high representation and precision, which are beneficial for the application of large combustion systems. In this study the temperature and concentration were measured in real time by water vapor and oxygen generated during combustion using Tunable Diode Laser Absorption Spectroscopy (TDLAS). The results showed that the average temperature inside the combustion system was 1330℃ and the mean oxygen concentration was 3.3 %, which showed similar tendency with plant monitoring data.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.5
• /
• pp.451-457
• /
• 2011

The main objective of this study is to investigate the variation in the ignition characteristics of coals as a function of moisture content in a laminar flow reactor (LFR) equipped with a fuel moisture micro-supplier designed by the Pusan Clean Coal Center. The volatile ignition position and time were observed experimentally when a pulverized coal with moisture was fed into the LFR under burning conditions similar to those at the exit of the pulverizer and real boiler. The reaction-zone temperature along the centerline of the reactor was measured with a $70-{\mu}m$, R-type thermocouple. For different moisture contents, the volatile ignition position was determined based on an average of 15 to 20 images captured by a CCD camera using a proprietary image-processing technique. The reaction zone decreased proportionally as a function of the moisture content. As the moisture content increased, the volatile ignition positions were 2.92, 3.36, 3.96, and 4.65 mm corresponding to ignition times of 1.46, 1.68, 2.00, and 2.33 ms, respectively. These results indicate that the ignition position and time increased exponentially. We also calculated the ignition-delay time derived from the adiabatic thermal explosion. It showed a trend that was similar to that of the experimental data.

• Journal of Korean Ophthalmic Optics Society
• /
• v.6 no.2
• /
• pp.71-75
• /
• 2001

In this paper, a three-dimensional measuring system of thermoluminescence(TL) spectra based on temperature, wavelength and luminescence intensity was introduced. The system was composed of a spectrometer, temperature control unit for thermal stimulation, photon detector and personal computer for control the entire system. Temperature control was achieved by using feedback to ensure a linear-rise in the sample temperature. Digital multimeter(KEITHLEY 195A) measures the electromotive force of Copper-Constantan thermocouple and then transmits the data to the computer through GPIB card. The computer converts this signal to temperature using electromotive force-temperature table in program, and then control the power supply through the D/A converter. The spectrometer(SPEX 1681) is controlled by CD-2A, which is controlled by the computer through RS-232 communication port. For measuring the luminescence intensity during the heating run, the electrometer(KEITHLEY 617) measures the anode current of photomultiplier tube(HAMAMATSU R928) and transmits the data to computer through the A/D converter. And, we measured and analyzed thermoluminescence of $CaSO_4$ : Dy, P using the system. The measuring range of thermoluminescence spectra was 300K-575K and 300~800 nm, $CaSO_4$ : Dy. P was fabricated by the Yamashita's method in Korea Atomic Energy Research Institute(KAERI) for radiation dosimeter. Thermoluminesce spectra of the $CaSO_4$ : Dy, P consist of two main peak at temperature of $205^{\circ}C$, wavelength 476 nm and 572 nm and with minor ones at 658 nm and 749 nm.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.345-350
• /
• 2017

Downsizing is widely applied to diesel engines in order to improve fuel efficiency and reduce exhaust emissions. Engine sizes are becoming smaller but pressure and temperature inside combustion chambers are increasing. Therefore, research for fuel spray under high pressure and temperature conditions is important. A constant volume chamber which simulates high temperature and pressure likely to be found in diesel engines was developed in this study. Pressure and temperature were increased abruptly because of ignition of the pre-mixture in the constant volume chamber. Then pressure and temperature were gradually decreased due to the heat loss through the chamber wall. Fuel spray occurred when temperature and pressure were reached at the target condition. In this experiment, the temperature condition should be exactly defined to understand the relation between fuel evaporation and ambient temperature. A fast response thermocouple was developed and used to measure the temporal and spatial temperature distribution during the combustion process inside the combustion chamber. In the results, the core temperature was slightly higher than the bulk temperature calculated by the gas equation. Ed-note: do you want to say 'ideal gas equation'? This was attributed to the heat transfer loss through the chamber wall. The vertical temperature deviation was higher than the horizontal temperature deviation by 5% which resulted from the buoyancy effect.

• The Journal of Korean Academy of Prosthodontics
• /
• v.44 no.5
• /
• pp.503-513
• /
• 2006

Statement of the problem: The cold-cured resins used in fabrication of the provisional crown and fixed partial dentures could cause pulpal damage by heat generated during exothermic polymerization reactions. Purpose: In this in vitro study investigates the how external conditions such as material of the matrix, thickness of the matrix and thickness of dentin affect the temperature of the tooth during polymerization reaction of the cold-cured resins. Material and methods : To measure the temperature of the resin, metal die was maintained to the temperature of $37^{\circ}C$ with water bath to simulate the temperature of thetooth and thermocouple was placed in the center of the metal die. Acrylic pipe was cut in height of 1, 2, 3, 6, 10 mm and placed on the metal die and mixed resin was pored in the acrylic pipe As the resin polymerized temperature was recorded with the thermometer. Temperature of the resin using matrix was recorded by using the individual tray relieved in different thickness 2, 5, 7, 10 mm. The material of the matrix was irreversible hydrocolloid impression material, vinyl polysilloxane impression material and vacuum-formed template Temperature rise of the resin using different thickness of tooth section was record ed by placing tooth section on the metal die and placing resin over the tooth section. Results : Conclusion : 1. Temperature rise increased as the thickness of the resin increased but there was no significant differences over 3 mm thickness of the resin. 2. The lowest temperature rise was showed in irreversible hydrocolloid impression material and vinyl polysilloxane impression material vacuum-formed template as in orders. 3, Temperature rise of the resin decreased regardless of the thickness of the matrix when vinyl polysilloxane impression material was used as the matrix. 4 When irreversible hydrocolloid impression material was used as matrix, the temperature rise of the resin decreased as the thickness of the matrix increased and there was no temperature rise when thickness of the matrix reached 10 mm, 5. The temperature rise of the resin did not decreased when Polypropylene vacuum-formed template was used as the matrix. 6, The temperature of the resin increased as the thickness of the dentin decreased.

• Journal of Environmental Health Sciences
• /
• v.13 no.1
• /
• pp.17-33
• /
• 1987

As a result of technical advances and industrialization, the characteristics of domestic and industrial wastes are becoming more complex. Accordingly, improved treatment and disposal systems are being continuously sought to take account of complex characteristics and to comply with economic restrictions. In this study, an application of pyrolysis to the treatment of industrial wastes, including waste scrap rubber, waste raw material used in making the slipper bottom and waste PVC pipe, and the effectiveness of pyrolysis in resource recovery from these wastes were investigated. Batches of wastes were pyrolysed by external heating to a temperature of 400-800$\circ$C in a 32 mm diameter x 0.9 m long silica tube to produce combustible gases, oils and chars. Before the start of pyrolysis runs, the entire system was purged with nitrogen gas to exclude the air. The temperature inside the retort was controlled by the thermocouple in the gas stream, and referred to as the pyrolysis temperature. Under these conditions three products were separately collected and further analyzed. The results were summarized as follows. 1. More gases and less chars were produced with higher pyrolyzing temperature and with higher rates of heating, but the yields of oils tended downwards at temperatures above 700$\circ$C. Accordingly, operating conditions of pyrolysis should be varied with desired material. 2. Calorific values and sulfur contents of produced oils were sufficient and suitable for fuel use. Chars from waste rubber had high heating values with low sulfur contents, but calorific values of chars from waste PVC and waste slipper were as low as 3, 065-4, 273 kcal/kg and 942-2, 545 kcal/kg, respectively. Therefore, char from these wastes are inappropriate for fuel. 3. Soluble contents of Pb, Cd, Cu and Zn in chars from waste rubber and waste slipper were below the Specific Hazardous Waste Treatment Standards. However soluble contents of Pb and Cd in chars from waste PVC were one or two times and five or seven times exceedingly the Specific Hazardous Waste Treatment Standards, respectively. 4. Post high heating is desirable for treatment method of waste PVC which generates toxic hydrogen chloride. 5. The proportions of hydrogen, methane and ethane in produced gases were in the range of 3.99-35.61% V/V, 18.22-32.50% V/V and 5.17-5.87% V/V, respectively. 6. Pyrolysis is a useful disposal method in case of waste slipper, which was hardly combustible, and thus investigations of this kind of materials are required for effective management of industrial waste. 7. Based upon the possible market development for products, overall pyroly economics to take account of treatment values of noncombustible or hazardous materials should be evaluated.

• Asian-Australasian Journal of Animal Sciences
• /
• v.19 no.10
• /
• pp.1429-1436
• /
• 2006

Fermentation characteristics, nutrient retention and aerobic stability of barley silages prepared using 6 commercial inoculants were evaluated using 126 mini-silos (3-L) in a completely randomized design. Whole barley forage was chopped, wilted to 39% DM and treated with water (control, S) or one of six inoculants: A (containing Lactobacillus plantarum); B (L. plantarum and Enterococcus faecium); C (L. plantarum and Pediococcus cerevisiae); D (L. plantarum, Pediococcus pentosaceus and Propionibacterium freudenreichii, plus hydrolytic enzymes); E (Lactobacillus buchneri plus hydrolytic enzymes); F (L. buchneri and P. pentosaceus plus hydrolytic enzymes). Samples of treated forage were collected for analysis at the time of ensiling, and then 18 silos of each treatment were filled, capped and weighed. Triplicate silos were weighed and opened after 1, 3, 5, 7, 33, and 61 d. On d 61, $400{\pm}5g$ of material from each silo was placed in 1-L styrofoam containers, covered with cheesecloth and held at room temperature. Silage temperature was recorded hourly for 14 d via implanted thermocouple probes. Chemical composition of the forage at ensiling was consistent with previously reported values. At d 61, pH was lowest (p<0.01) in silage S. Ammonia-N was lower (p<0.05) in silage A than in silages S, B, E, or F. Compared to pre-ensiling values, water soluble carbohydrate concentrations were elevated in silages S, A, B, C and D, and decreased in E and F. Lactic acid concentrations were similar (p>0.10) across treatments. Acetic acid levels were highest (p<0.01) in silage E and lowest (p<0.01) in silage D. Recovery of DM was lower (p<0.01) in silage F than in silages S, A, B, C, or D. On d 61, yeasts were most numerous (p<0.01) in silage D, which was the only silage in which temperature rose more than $2^{\circ}C$ above ambient during aerobic exposure. Silage D also had the highest (p<0.01) pH and ADIN content after aerobic exposure. Lactic acid and WSC content of silage D decreased dramatically during the 14-d aerobic exposure period. Yeast counts (at d 14 of exposure) were lowest (p<0.01) in silages E and F. In general, the commercial inoculants did not appear to enhance the fermentation of barley silage to any appreciable extent in laboratory silos.