• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.200.2-200.2
• /
• 2011

This study was carried out in order to estimate the greenhouse performance for Ground filtration water source heat pump which was installed for supplying the heat to the paprika greenhouse in Jinju city. Experimental area of Greenhouse was $3,300m^2$, For keeping the heat from greenhouse, single plastic covering and double thermal screen was installed. With considering all of greenhouse insulation condition and designed heatng temperature, heating capacity for experimental greenhouse was calculated as 320,000kcal/hr. Coefficient of performance(COP) of Ground filtration water source heat pump was gauged and greenhouse heating performance was tested from Febuary 1 to Febuary 28 in 2011. The result showed that COP of heat pump was in the range of 3.7~4.7 and COP of heating system was in the range of 3.0~3.5. The vaule of COP was very high and the temperature inside greenhouse was well corresponded to the setting temperature of greenhouse environment controlling system. lots of Ground filtration water made the the number of well fewer and the expense for installing heating system cheaper than that of geothermal system used custmarily. and this system went beyond the limitation of intaking amount of groundwater in normal Groundwater source heat pump.

• 한국세라믹학회지
• /
• 제26권1호
• /
• pp.139-145
• /
• 1989

An eutectic melt in the system(Bi2O3)0.85·(Nb2O5)0.15-6Bi2O3·SiO2 was unidirectionally solidfield at a rate of 0.5mm/h under a thermal gradient of 100℃/cm. Double crucibles and seed crystal plate were used in order to botain the composite crystals which had uniform microstructure throughout the ingot. The obtained composite crystals showed uniform microstructure, in which needle-like δ-(Bi2O3)0.85·(Nb2O5)0.15 crystals were arrayed in parallel in a matrix of γ-6Bi2O3·SiO2 single crystal. It was found that the <110> direction of δ-(Bi2O3)0.85·(Nb2O5)0.15 crystal was essentially parallel to the <111> direction of γ-6Bi2O3·SiO2 crystal in the composite crystals. A transverse thin plate of the composite crystals showed a high resolution optical transmission like an optical fiber array, and sharp chatoyancy was observed in the cabochon shaped composite crystals. Then, this may be useful for applications such as screen of a cathode ray tube or artificial cat's eye gem stones.

• 전자공학회논문지D
• /
• 제35D권4호
• /
• pp.9-17
• /
• 1998

BiNbO$_{4}$ ceramics with 0.07wt% V$_{2}$O$_{5}$ and 0.03wt% CuO (BNC3V7) sintered at 900 .deg. C where it is possible for these to be co-fired with ag electronde. Dielectric constant of 44.3 TCF (Thermal Coefficient of resonance Frequency) of 2 ppm/.deg. C and Qxf value 22,000 GHz can be obtained from BNC3V7. the laminatedchip LC filter is indispensible to the minimaturization of PCS (Personal Communication System) terminals. Therefore, multilayer type BPF has been fabricated by screen-printing with silver electrode after tape casting. The simulated characteristics of the fabricated filters sintered at 900.deg. C werecomparedwith the designed ones. for Band Pass Filter widths was similar that ofdesigned ones. For Low Pass Filter (LPF), insertion loss value of band pass widths (2.4 dB) which is a few higher than that of designed (1dB), but characteristization of band pass widths was similar that of designed ones.s.of designed ones.s.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1806-1809
• /
• 2008

Study that form micro pattern by direct ink jet printing method is getting attention recently. Direct ink jet printing spout fine droplet including nano metal particle by force or air pressure. There is reason which ink jet printing method is profitable especially in a various micro-patterning technology. It can embody patterns directly without complex process such as mask manufacture or screen-printing for existent lithography. In this study, research of a technology that ejects fine droplet form of Pico liter and forms metal micro pattern was carried with inkjet head of piezoelectricity drive system. Droplet established pattern while ejecting consecutively and move on the surface at the fixed speed. Patterns formed in ink are mixed with organic solvent and polymer that act as binder. So added thermal hardening process after evaporate organic solvent at isothermal after printing. I executed high frequency special quality estimation of CPW transmission line to confirm electrical property of manufactured circuit board. We tried a large area printing to confirm application possibility of an ink jet technology.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.206.1-206.1
• /
• 2014

최근 전자 장비의 금속 전도성 패턴 제작에 있어서 직접적인 프린트가 가능한 프린팅 기술이 기존의 복잡한 photolithography 를 대체할 기술로 주목 받고 있다. 이와 함께 금속 전도성 패턴 제작에 사용되는 고가의 전도성 물질인 Ag ink 및 paste 를 저가의 Cu ink 및 paste 로 대체하기 위한 연구가 진행되고 있다. 하지만 일반적으로 copper 는 대기 중 에서 쉽게 산화되어 높은 저항을 야기시킨다. 따라서 Cu ink 또는 paste 를 제작할 때 copper nanoparticles 을 유기 용매에 분산하여 inert atmosphere에서 합성하거나 [1] copper ink 또는 paste 를 substrate 에 프린트하여 reduction atmosphere 에서 소성시킨다 [2]. 이번 연구에서 Cu paste 를 유리 기판에 screen printing 하여 혼합가스(질소 95%, 수소 5%)와 질소 가스 분위기에서 소성하여 Cu 전극의 소성 거동과 전기적 특성을 분석하였다. 4-point probe를 통해 소성된 Cu 전극의 저항을 측정하여 전도도를 조사하였으며 Thermal Gravimetric Analysis (TGA), Fourier Transform Infrared(FTIR)를 통해 소성된 Cu 전극의 유기물 분해가 전도도에 미치는 영향을 분석하고 Field Emission Scanning Electron Microscopy (FESEM)과 High Resolution Transmission Electron Microscopy (HRTEM)을 통해 Cu nanoparticles 의 grain growth가 전도도에 미치는 영향을 조사하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.472.2-472.2
• /
• 2014

현재 결정질 실리콘 태양전지의 전 후면 전극의 형성은 스크린 프린팅 방법이 주를 이루고 있다. 스크린 프린팅 방법은 쉽고 빠르게 인쇄가 가능한 반면 단가가 높고 금속 페이스트에 첨가된 여러 혼합물에 의해서 전극과 기판 사이의 저항이 크다는 단점이 있다. 본 논문에서는 도금을 이용하여 태양전지의 전극을 형성한 후 태양전지의 전기적 특성을 비교하였다. 또한 단일반사방지막($SiN_x$) 증착 후 도금을 이용한 전극 형성 시 반사방지막의 pin-hole에 의해 전극 이외의 표면에 도금이 되는 ghost plating 현상이 발생하게 되는데, 이를 방지하기 위해 thermal oxidation을 이용하여 SiO2/SiNx 이중반사 방지막을 증착함으로써 ghost plating을 최소화 시켰다. Ni을 이용하여 전극과 기판 사이의 저항을 낮추었으며, 주요 전극은 Cu 도금을 사용함으로써 단가를 낮추었으며 마지막으로 Cu전극의 산화를 방지하기 위해 Ag을 이용하여 얇게 도금하였다. 실험에 사용된 Si 웨이퍼 특성은 p-형, $156{\times}156mm2$, $200{\mu}m$, $0.5{\sim}3.0{\Omega}{\cdot}cm$ 이다. 웨이퍼는 표면조직화, p-n접합 형성, 반사방지막 코팅을 하였으며 스크린 프린팅 방법을 이용해 후면 전극을 인쇄하고 열처리 과정을 통해 전극을 형성하였다. 이 후 전면에 레이저를 이용해 전극 패턴을 형성한 후 도금을 실행하여 태양전지를 완성하였다. 완성된 태양전지는 솔라 시뮬레이터, QE 및 TLM패턴을 이용하여 전기적 특성을 분석하였으며, SEM과 linescan, 광학현미경 등을 이용하여 전극을 분석하였다.

• 한국표면공학회지
• /
• 제46권4호
• /
• pp.162-167
• /
• 2013

Encapsulation is required since organic materials used in OLED devices are fragile to water vapor and oxygen. Laser sealing method is currently used where IR laser is scanned along the glass-frit coated lines. Laser method is, however, not suitable to encapsulating large-sized glass substrate due to the nature of sequential scanning. In this work we propose a new method of encapsulation using Joule heating. Conductive layer is patterned along the sealing lines on which the glass frit is screen printed and sintered. Electric field is then applied to the conductive layer resulting in bonding both the panel glass and the encapsulation glass by melting glass-frit. In order to obtain uniform bonding the temperature of a conductive layer having a shape of closed loop should be uniform. In this work we conducted simulation for heat distribution according to the structure of a conductive layer used as a Joule-heat source. Uniform temperature was obtained with an error of 5% by optimizing the structure of a conductive layer. Based on the results of thermal simulations we concluded that Joule-heating induced encapsulation would be a good candidate for encapsulation method especially for large area glass substrate.

• 한국안전학회지
• /
• 제19권3호
• /
• pp.51-56
• /
• 2004

Conductive polymer blends and composites are widely used for different safety application such as electrostatic charge dissipation(ESD), electromagnetic interference(EMI) shielding, electrostatic prevention and safety chemical sensor. In order to prepare a impedance-type humidity sensor that is durable at high humidities and high temperature, electically conductive polymer blends based on diallyldimethylammonium chloride(DADMAC) and epoxy were prepared in this study. The polymer blends type conductive ionomer exhibits reaction each other DADMAC and epoxy in FT-IR and DSC analysis. The blends material was traced by new peak at 1600cm-1 and appeard improvement of thermal resistance by melting point shift. Alumina substrate was deposited a pair of gold electrodes by screen printing. The blend material were spin-coated with a thin film type on the surface of alumina substrate. The polymer bleld type sensor exhibits a linear impedance increasing better than DADMAC coated humidity sensor. Also it shows good sensitivity, low hysteresis and durability against high humidity.

• 대한화학회지
• /
• 제45권3호
• /
• pp.236-241
• /
• 2001

$Y_2O_3$: Eu 형광체는 고효율, 열적 화학적 안정성을 갖고 있어서 평판 표시 소자용 적색 형광체로 널리 사용되고 있다. 고분해능과 고효율을 가지는 평판 표시 소자는 작은 크기의 구형 입자를 가진 형광체를 필요로 한다. 본 연구에서는 착체 중합법을 이용하여 100-300nm크기의 $Y_2O_3$ : Eu 형광체를 제조하였고 1족 혹은 2족 원소를 첨가하여 발광특성에 대한 영향을 검토하였다.

• 대한기계학회논문집B
• /
• 제29권1호
• /
• pp.87-94
• /
• 2005

A computer code for Electrical Capacitance Tomography (ECT) is developed to sense the cross sectional phase distribution of two-phase flow in the rectangular pipe in which the tomography sensor furnished by the insulated wall, electrodes, and electric field screen. The computer code had two steps for the image reconstruction. In the forward projection step, the sensitivity matrix was constructed based on the electric field calculated by the finite difference method. In the backward projection step, the sensitivity matrix and the measured capacitances were used to reconstruct the cross sectional image. Several algorithms including LBP, TR, ITR, and PLI were employed to find the proper one for the two-phase flow analysis. Since the dielectric constant of the water in two-phase flow is sensitive to the thermal parameter such as, temperature and pressure, the developed code was evaluated to find their accuracy, speed of calculation, and sensitivity to the variation of the dielectric constant. It was found that the iterative methods are superior to the direct methods for the image reconstruction, and the PLI method was the best in the variation of the dielectric constants.