• 항공우주기술
• /
• 제6권2호
• /
• pp.141-149
• /
• 2007

재생냉각과 막냉각 그리고 열차폐 코팅이 적용된 재생냉각 축소형 연소기를 이용하여 연소시험을 수행하였다. 시험결과 적용된 냉각 방식은 설계 조건에서 그 역할을 충실히 수행하였으나 연료 매니폴드 내에 삽입된 구조 보강용 링에 의한 연료 유동의 불안정성으로 인해 고주파 연소불안정이 발생하였다. 연료 유동의 불안정성은 삽입 링을 제거함으로써 개선되었고 추가 연소시험을 통해 수정된 연소기의 연소안정성을 검증할 예정이다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.699-702
• /
• 2008

This paper describes the numerical simulations in the cooling of the radiator in a distribution transformer. The aim of this work is the cooling optimization of the transformer by CFD simulations. A clear understanding of the cooling pattern in a radiator which is a main heat remover in the power transformer is essential for optimizing the radiator design increasing the thermal efficiency. In this paper we study the heat transfer and fluid flow in a 3-phase 400kVA transformer. The plate radiators of this transformer become wrinkled (corrugated radiator) and there are filled with transformer oil. The oil is circulated due to the natural convection driven by buoyancy effects through radiators so that the ultimate cooling medium is the surrounding air. In the design of transformers, it is of interest to minimize the cost and size of radiators. The obtained results show the temperature and flow distributions and the possibility to optimize the transformer with 3-dimensional CFD models using FLUENT.

• 한국태양에너지학회 논문집
• /
• 제22권2호
• /
• pp.39-47
• /
• 2002

The thermosyphon SDHWS and the loop type thermosyphon systems are widely used for domestic hot water system. The loop type thermosyphon is a circulation device for transferring the heat produced at the evaporator to the condenser area in the loop. In this study, the operating characteristics of various working fluids being used have been identified. The working fluids employed in the study were ethanol. water, and a binary mixture of ethanol and water. The volume of working fluid used in this study were 30%, 40%, 50%, 60% and 70% of evaporator volume. It is observed that, in the thermosyphon with low volume of working fluid, such as 30% or 40%, the fluid was dried out. The flow pattern and mechanism of the heat transfer were identified through this study. Flow patterns of the binary mixture working fluid were also investigated, and the patterns were recorded in the camera. The system parameters were calculated using the thermal performance data. Modelling of the system was carried out using PSTAR method and TRNSYS program.

• 설비공학논문집
• /
• 제20권12호
• /
• pp.789-794
• /
• 2008

Recently, much attention has been paid in the field of defrosting because clear windshield in vehicle without effecting the thermal comfort is realized essentially. Then in winter, defrosting performance is one of the important factors in vehicle design to make certain driver's view. In this study, the velocity profile, temperature distribution and frost melting pattern on the windshield screen have been predicted in three dimensional geometry of an automobile interior. Numerical analyses predict a detailed description of fluid flow and temperature patterns on the inside windshield screen, utilizing the flow through defroster nozzle. Numerical prediction established a good defrosting performance with the standard distance ratio and the defroster nozzle angle ranging from $30^{\circ}$ to $40^{\circ}$, which satisfy the condition of National Highway Traffic Safety Administration (NHTSA) completely.

• Korean Chemical Engineering Research
• /
• 제62권2호
• /
• pp.191-199
• /
• 2024

A study was conducted on a tubular heat exchanger to improve its heat transfer rate by using a novel baffle plate design with discontinuous swirling patterns. The design consisted of perforated baffle plates with rectangular air deflectors positioned at varying angles. The tubes in the heat exchanger were arranged in a consistent alignment with the airflow direction and exposed to a uniform heat flux on their surfaces. Each baffle plate included sixteen deflectors inclined at the same angle and arranged in a clockwise pattern. This arrangement induced a swirling motion of the air inside a circular duct where the heated tubes were located, leading to increased turbulence and improved heat transfer on the tube surfaces. The spacing between the baffle plates was adjusted at different pitch ratios, and the Reynolds number was controlled within a range of 16,000 to 29,000. The effects of pitch ratios and inclination angles on the heat exchanger's performance were analyzed. The results indicated that using a baffle plate with rectangular deflectors inclined at 30° and a pitch ratio of 1.2 resulted in an average increase of 1.29 in the thermal enhancement factor.

• 설비공학논문집
• /
• 제22권3호
• /
• pp.123-129
• /
• 2010

The district heating users can be generally classified into two groups such as apartments and buildings. In consideration that the time zone of the maximum heat load for apartments is different from those of buildings during a day, the maximum heat supply range is presented. In case of the investigated area, the maximum heat supply is occurred at the ratio between apartments and buildings that is 65%：35%. Thus the heat supply range is increased as much as 15% if the time zone when the maximum heat load is occurred is considered.

• 대한기계학회논문집B
• /
• 제22권4호
• /
• pp.440-451
• /
• 1998

An experimental study has been conducted to investigate solidification of NH$_{4}$CI-H$_{2}$0 mixtures inside a vertical rectangular enclosure. Solidification process is visualized by the shadowgraph method. Emphasis is placed on the effect of solidification parameters such as the aspect ratio, cooling wall temperature and initial composition. The aspect ratio shows a dominant effect on the number and developing time of the double diffusive layers which reveals the relative strength of solutal convection to thermal convection. Similar flow pattern is observed when the concentration difference between interdendritic liquid and the pure liquid which drives solutal convection is the same regardless of the different cooling wall temperature and initial concentration.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.718-723
• /
• 2009

The purpose of this study is to present an in-site evaluation method for building insulation performance using Infra-red camera. The research contents of this study are to evaluate validity and suitability of building insulation defect survey using Infra-red camera for apartment housing with temperature & heat flow pattern analyze method. By establishing the in-site evaluation method building insulation performance using infra-red camera, it is expected that 1) building envelope repair market will be activated by using developed method in ESCO and remodeling companies, 2) the method developed in this research will contribute to reduce national energy consumption by promoting old building insulation remodeling.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 춘계학술대회논문집
• /
• pp.106-111
• /
• 2000

The residual stresses in molded plastic parts can be divided into the flow induced residual stresses produced in flowing stages and the thermally induced residual stresses produced in cooling state. Reducing residual stresses in the final parts is one of the goals in recent study. The present study focused on comparing the predicted values for thermal residual stresses in freely and constrained quenched plastic plates with and without free volume theory. As a result the final residual stresses showed the opposite pattern in thickness direction. furthermore by applying free volume theory the predicted residual stress at the center showed about 50% of the values without free volume theory for constrained quenched case.

• 한국공작기계학회논문집
• /
• 제18권2호
• /
• pp.144-153
• /
• 2009

It is widely known that no-slip assumptions are often violated on regular basis in micrometer- or nanometer-scale fluid flow. In the case of cavity-filling process of nanoimprint lithography(NIL), slip phenomena take place naturally at the solid-to-liquid boundaries, that is, at the mold-to-polymer or polymer-to-substrate boundaries. If the slip or partial slip phenomena are promoted at the boundaries, the processing time of NIL, especially of thermal-NIL which consumes more tact time than that of UV-NIL, can be significantly improved. In this paper it is aimed to elucidate how the cavity-filling process of NIL can be influenced by the slip phenomena at boundaries and to what degree those phenomena increase the process rate. To do so, computational fluid dynamics(CFD) analysis of cavity filling process has been carried out. Also, the effect of mold pattern shape and initial thickness of polymer resist were considered in the analysis, as well.