• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.12
• /
• pp.809-814
• /
• 2014

Spinel thin films were prepared by the spin spray technique to develop new thermal imaging materials annealed at low temperature for uncooled microbolometer applications. The spinel thin films were deposited from $[(Ni_{0.30}Co_{0.33}Mn_{0.37})_{1-x}Cu_x]_3O_4$ ($0.1{\leq}x{\leq}0.2$) solutions and then annealed at $400^{\circ}C$ for 1 h in argon. Effects of Cu content (x) and deposition time on the electrical properties of the annealed films were investigated. With increasing deposition time, the resistivity of the annealed films increased. For the annealed films deposited for 1 min, the resistivity of x=0.15 films was lower than that of x=0.1 films due to the different grain sizes. The high temperature coefficient of resistance (TCR) of the annealed films could be obtained at temperature below $50^{\circ}C$. Typically, the resistivity of $127{\Omega}{\cdot}cm$ and TCR of -5.69%/K at $30^{\circ}C$ were obtained for x=0.1 films with deposition time of 1 min annealed at $400^{\circ}C$ for 1 h in argon.

• Journal of radiological science and technology
• /
• v.39 no.1
• /
• pp.89-97
• /
• 2016

As previous studies to proceed with the evaluation of the radioactive at linear accelerator's shielding concrete wall. And the shielding wall was evaluated the characteristics for the incoming neutron. As a result, the shielding wall is the average amount of incoming neutrons 10 MV 4.63E-7%, 15 MV 9.69E-6%, showed the occurrence of 20 MV 2.18E-5%. The proportion of thermal neutrons of which are found to be approximately 18-33%. The neutron generation rate can be seen as a slight numerical order. However, in consideration of the linear accelerator operating time we can not ignore the effects of neutrons. Accordingly radioactive problem of the radiation shield wall of the treatment room will be this should be considered.

• Korean Journal of Materials Research
• /
• v.30 no.7
• /
• pp.350-358
• /
• 2020

A variety of composite powders having different aluminum and carbon contents are prepared using various organic solvents having different amounts of carbon atoms in unit volume as ball milling agents for titanium and aluminum ball milling. The effects of substrate temperature and post-heat treatment on the texture and hardness of the coating are investigated by spraying with this reduced pressure plasma spray. The aluminum part of the composite powder evaporates during spraying, so that the film aluminum content is 30.9 mass%~37.4 mass% and the carbon content is 0.64 mass%~1.69 mass%. The main constituent phase of the coating formed on the water-cooled substrate is a non-planar α₂ phase, obtained by supersaturated carbon regardless of the alloy composition. When these films are heat-treated at 1123 K, the main constituent phase becomes γ phase, and fine Ti₂AlC precipitates to increase the film hardness. However, when heat treatment is performed at a higher temperature, the hardness is lowered. The main constitutional phase of the coating formed on the preheated substrate is an equilibrium gamma phase, and fine Ti₂AlC precipitates. The hardness of this coating is much higher than the hardness of the coating in the sprayed state formed on the water-cooled substrate. When hot pressing is applied to the coating, the porosity decreases but hardness also decreases because Ti₂AlC grows. The amount of Ti₂AlC in the hot-pressed film is 4.9 vol% to 15.3 vol%, depending on the carbon content of the film.

• Polymer(Korea)
• /
• v.29 no.1
• /
• pp.81-86
• /
• 2005

In this study, waterborne polyurethanes were synthesized with poly(tetramethylene glycol) (PTMG), polycarprolactone PCL), dimethylol propionic acid (DMPA) and different molar ratio of chain extender. Particle size, polydispersity, thermal and mechanical properties of waterborne polyurethane were investigated. The particle size of waterborne polyurethane was in the range of 5∼200 nm and decreased with increasing the amounts of PCL and chain extender. Glass transition temperatures ($T_g$) were in the range of -70∼-45 ${\circ}C$ and increased with as PCL and chian extender (ED) contents increased. The $T_g$ of polyurethane prepared from the mixture showed similar trends as compared with those of in the same values of synthetic polyurethane using PTMG or PCL, respectively. Also, mechanical properties of mixed polyols (PTMG and PCL) were lower than those of PTMG and PCL, respectively.

• Nuclear Engineering and Technology
• /
• v.48 no.2
• /
• pp.533-544
• /
• 2016

This paper provides a reference to determine the seal performance of metallic O-rings for a reactor pressure vessel (RPV). A nonlinear elastic-plastic model of an O-ring was constructed by the finite element method to analyze its intrinsic properties. It is also validated by experiments on scaled samples. The effects of the compression ratio, the geometrical parameters of the O-ring, and the structure parameters of the groove on the flange are discussed in detail. The results showed that the numerical analysis of the O-ring agrees well with the experimental data, the compression ratio has an important role in the distribution and magnitude of contact stress, and a suitable gap between the sidewall and groove can improve the sealing capability of the O-ring. After the optimization of the sealing structure, some key parameters of the O-ring (i.e., compression ratio, cross-section diameter, wall thickness, sidewall gap) have been recommended for application in megakilowatt class nuclear power plants. Furthermore, air tightness and thermal cycling tests were performed to verify the rationality of the finite element method and to reliably evaluate the sealing performance of a RPV.

• Archives of Plastic Surgery
• /
• v.47 no.1
• /
• pp.20-25
• /
• 2020

Background Ultrasonic dissection devices cause less thermal damage to the surrounding tissue than monopolar electrosurgical devices. We compared the effects of using an ultrasonic dissection device or an electrocautery device during prosthetic breast reconstruction on seroma development and short-term postoperative complications. Methods We retrospectively reviewed the medical records of patients who underwent implant-based reconstruction following mastectomy between March 2017 and September 2018. Mastectomy was performed by general surgeons and reconstruction by plastic surgeons. From March 2017 to January 2018, a monopolar electrosurgical device was used, and an ultrasonic dissection device was used thereafter. The other surgical methods were the same in both groups. Results The incidence of seroma was lower in the ultrasonic dissection device group than in the electrocautery group (11 [17.2%] vs. 18 [31.0%]; P=0.090). The duration of surgery, total drainage volume, duration of drainage, overall complication rate, surgical site infection rate, and flap necrosis rate were comparable between the groups. Multivariate analysis revealed that the risk of seroma development was significantly lower in the ultrasonic dissection device group than in the electrocautery group (odds ratio for electrocautery, 3.252; 95% confidence interval, 1.242-8.516; P=0.016). Conclusions The findings of this study suggest that the incidence of seroma can be reduced slightly by using an ultrasonic dissection device for prosthesis-based breast reconstruction. However, further randomized controlled studies are required to verify our results and to assess the cost-effectiveness of this technique.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.12
• /
• pp.979-984
• /
• 2016

Recently, ball screws have been used in machine tools, robot parts, and medical instruments. The demand for ball screws of high precision and reduced size is increasing because of the growth of high value-added industries. Three types of ball screws are typically used: deflector type, end-cap type, and tube type. They are also classified from C0 to C9 according to the precision level. A deflector type ball screw can reduce the variation of rotational torque and the size of the nut of the ball screw is minimized. To ensure the reliable design of ball screws, it is important to perform a structural analysis. The purpose of this study is to perform a stability evaluation through analysis of a deflector type miniature ball screw for weapon systems. The analysis is performed through Finite Elements Method (FEM) simulation to predict characteristics such as deformation, stress, and thermal effects. The interference between the shaft and the deflector for smooth rotation are also studied. Based on the results of the analysis, the development of the deflector type miniature ball screw for weapon systems is performed.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.760-760
• /
• 2012

도심 지역은 인구집중, 토지 피복의 변화 및 교통량 증가 등의 인공열 배출원의 다양화 등의 요인에 의해 주변지역보다도 기온이 높은 도시 열섬(Urban Heat Island) 현상에 의해 독특한 도시기후의 특색을 보이게 된다. 일반적으로 도시 열 환경에 대한 연구는 도시 열섬의 강도나 현상을 파악하는데 집중되어 왔다. 최근 들어 도시 열섬 현상 완화 또는 개선을 위한 관심이 높아지면서 도시내에 존재하는 수면이나 녹지를 이용한 기후개선에 대한 연구가 진행되고 있다. 하천은 다양한 생물이 서식하는 공간이면서 생물의 다양성이 풍부한 생태계의 보고로 인간과 환경이 조화를 이루어 온 공간이기도 하다. 이와 같이 하천은 지역의 다양성과 특수성에 따라 가지고 있는 기능이 다양하다. 그 중 하천의 환경 기능은 많은 열용량을 축적시켜 수면의 온도상승을 적게 하여 하천의 온도는 물론 주변지역의 온도를 낮추는 역할을 하게 된다. 특히 흐르는 물은 대류와 혼합과정을 거치며 열을 운반할 수 있으므로 효율적인 축열체가 된다. 또한 하천의 물 등은 광의 투과성이 높기 때문에 표면에서는 반사되지 않고 수체 내에 열을 저장한다. 따라서 이러한 현상이 종합적으로 작용하여 도심하천은 도심지에서 높게 형성된 온도를 낮추는 냉각효과가 있다고 판단된다. 이러한 영향을 알아보기 위해 본 연구에서는 원격탐사 기법을 이용하여 도심하천이 도시 열완경 완화에 미치는 영향을 분석하였다. 분석을 위해 2009년 9월 6일 Landsat 7 ETM+ 위성영상을 이용하여 LST (Land Surface Temperature)를 추출하고, SEBAL (Surface Energy Balance Algori- thms for Land) 모델을 이용하여 지표면 열수지 성분을 추출하였다. 그 결과, 도심하천 주변의 온도가 도심지에 비해 $2{\sim}3^{\circ}C$ 정도 낮게 형성되었으며, 잠열은 주변 도심지에 비해 하천에서 높은 분포를 나타내었다. 그러나 하천 둔치나 하천 주변의 콘크리트, 아스팔트 및 나대지 등의 토지피복은 지표면 온도가 높게 형성되어 도심의 heat spot으로 작용하여 열 환경을 악화시키나 도심하천은 cool spot 작용을 하여 도심의 열을 완화하는 기능을 갖는 것으로 판단된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.245.2-245.2
• /
• 2013

Solution processed organic photovoltaic devices have relatively less attention compared to polymer photovoltaic devices even though they have high possibility to be developed because they have both advantages of polymer and organic, such as solution processable, no synthetic batch dependence of photovoltaic performance, high purity and high charge carrier mobility as well as relatively high efficiency (~7%). In addition, solution processed organic photovoltaic devices have an advantage of easiness to study the relationship between the molecular structure and photovoltaic performance due to its simple structure. In this work, five isoindigo based low band gap donor-acceptor-donor (D-A-D) small molecules with different electron donating strength were synthesized for investigating the relationship between the molecular structure and photovoltaic performance, especially, investigating the effects of different electron donating effect of donor group in isoindigo backbone to photovoltaic device performance. The variation of electron donating strength of donor group strongly affected the optical, thermal, electrochemical and photovoltaic device performances of isoindigo organic materials. The highest power conversion efficiency of ~3.2% was realized in bulk heterojuction photovoltaic device consisted of the ID3T as donor and PC70BM as acceptor. This work demonstrates the great potential of isoindigo moieties as electron deficient units as well as guideline for synthesis of donor-acceptor-donor (D-A-D) small molecules for realizing highly efficient solution processed organic photovoltaic devices.

• Korean Journal of Materials Research
• /
• v.9 no.6
• /
• pp.599-603
• /
• 1999

We have investigated the growth characteristics of thick GaN on Sim substrate with AlN and low temperature GaN buffer layer. The vertical hydride vapor phase epitaxy system with $GaCl_3$ precursor was used for growth of GaN. AlN and GaN buffer layer were deposited on Si substrate to reduce the lattice mismatch and the thermal expansion coefficient mismatch between si and GaN. Optimization of deposition condition for AlN and low temperature GaN buffer layers were carried out. We studied the effects of growth temperature, V/III ratio on the properties of thick GaN. Surface morphology, growth rate and crystallinity of thick GaN were measured using Atomic Force Microscopy (AFM), $\alpha-step$-, Scanning Electron Microscopy (SEM) and X-Ray Diffractometer(XRD).