• Journal of the Korean Solar Energy Society
• /
• v.27 no.1
• /
• pp.55-61
• /
• 2007

This paper describes the procedure and calculation results of basic design and transient variation of performance of 1 MWe large scale solar thermal power plant (STPP) by using the commercial software of THERMOFLEX and TRNSYS, respectively. In order to simulate the transient variation of STPP, the results of basic design are necessary. The design standard of the STPP is 1 MWe generation with solar only at high DNI condition and then 0.6 MWe output power for 1 hour using stored energy when the DNI becomes lower unable to operate normally. The results of basic design show the important design data of flow rates, water/steam conditions at each equipments and the estimated efficiency of STPP. In addition, dynamic simulation results of STPP are predicted and plotted for one year and three different days weather data of Daejeon.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.39 no.1
• /
• pp.55-62
• /
• 2015

This study investigated the thermal insulation of an air-cell pack embedded jacket and down jackets to understand the potential of air-cell pack as a filler for winter outdoor wear. A thermal manikin measured the thermal insulation of the following jackets: HD (heavy down jacket, total weight (Tw) 750g, goose down weight (Dw) 350g), LD (light down jacket, Tw 560g, Dw 140g), AF (air-cell pack embedded jacket, Tw 490g, trunk goose down in LD was replaced to air cell), F (film jacket, Tw 469g, but removed the air in the air-cell pack from the AF), and Control (control jacket, Tw 438g, removed the air-cell pack film from the F). Thermal insulations of each experimental condition were measured in a static standing posture. Total thermal insulations (IT) were 1.29clo (HD), 1.23clo (LD), 1.16clo (AF), 1.20clo (F), and 1.08clo (Control). Body regional thermal insulation was higher in the chest and back than in the abdomen and hip in all conditions. The results suggest that an economical and versatile outdoor jacket with superior thermal insulation will be feasible if the air volume is properly controlled in air-cell pack embedded jackets in consideration of regional different distribution and used in combination with film and down.

• 한국전산유체공학회:학술대회논문집
• /
• 2003.10a
• /
• pp.248-250
• /
• 2003

Thermal analysis is performed to protect the propulsion system of low-earth-orbit earth observation satellite from unwanted thermal disaster like propellant freezing. To implement thermal design adequately, heater powers for the propulsion system estimated through the thermal analysis are decided. Based on those values anticipated herein, the average power for propulsion system becomes 22.02 watts when the only one redundant catalyst bed heater is turned on. When for the preparation of thruster firing, 25.93 watts of the average power is required. All heaters selected for propulsion components operate to prevent propellant freezing meeting the thermal requirements for the propulsion system with the worst-case average voltage, i.e. 25 volts.

• Korean Journal of Computational Design and Engineering
• /
• v.4 no.4
• /
• pp.318-326
• /
• 1999

Recently, electronic systems including computers have been rapidly shrinking in size while at the same time the complexity and the capability of these systems continue to grow/sup [1]/. Thus, system volumes have decreased as system power has increased, resulting in dramatic increases in system heat density. The high temperature of the computer system is considered as the major reason for low performance and shortening life of the product. It is necessary to solve this problem due to the heat density increased and to develop the design skill of the computer cabinet according to miniaturization. M4500 desk-top computer was selected for analyzing the thermal management inside cabinet. The cabinet volume, the configuration of the heating devices, the size and location of air ventilation, and the fan selection have been investigated as the important parameters to find out an optimal cabinet design. The objectives of this project were to analyze which design parameters would affect cooling performance by thermal strategy, to design an optimal model, and to measure the temperatures of the main parts to confirm the effect of the thermal design. The temperatures of each part of the optimal model were compared with those of the existing model. As a result. the volume of this miniaturized model was about 16% smaller than that of M4500 without any change in operating performance.

• Journal of Ship and Ocean Technology
• /
• v.12 no.3
• /
• pp.1-13
• /
• 2008

In shipbuilding, diverse manufacturing techniques for automation have been developed and used in practice. Among them, however, the hull forming automation is the one that has not been of major concern compared with others such as welding and cutting. The basis of the development of this process is to find out how to extract thermal forming information. There exist various methods to obtain such information and the 3D design shape that needs to be formed should be extracted first for getting the necessary thermal forming information. Except well-established shipyards which operate 3D design systems, most of the shipyards only rely on 2.5D design systems and do not have an easy way to obtain 3D surface design data. So in this study, various shipbuilding design systems used by shipyards are investigated and a 3D design surface data extraction method is proposed from those design systems. Then an example is presented to show the extraction of real 3D surface data using the proposed method and computation of thermal forming information using the data.

• Aerospace Engineering and Technology
• /
• v.10 no.2
• /
• pp.20-28
• /
• 2011

The electro-optical payload of a low-earth orbit satellite is thermally decoupled with the bus, which supports a payload for a mission operation. The payload has a cooling unit of FPA(Focal Plane Assembly) which has a thermal behavior increasing its temperature instantly during an operation in order to dissipate a waste heat into the space. The FPA cooling unit should include a radiator and heatpipes with a sufficient performance in worst hot condition, and a heater design to maintain its temperature above a minimum allowable temperature in the worst cold condition. In this paper, we analyzed the thermal requirements and the heater design constraints from the thermal analysis results for the current thermal design of the FPA cooling unit and the design elements of the better heater design were found.

• Journal of Power System Engineering
• /
• v.13 no.6
• /
• pp.35-42
• /
• 2009

The piping systems in the steam-driven power engines lie under the cyclic condition of thermal expansion and contraction by superheated steam. These phenomena might cause some severe damages on the pipes and the accessory devices. To avoid these damages, the calculation of the proper strength and the consideration of the reduced resultant forces on the materials are needed. In the present study, numerical investigations on the effects of the thermal deformation of the industrial piping system were performed with comparison of the design data. Commercial software, ABAQUS with the thermal-fluidic loadings based on the design conditions was used for the thermal stress analysis of the piping system. From the analysis of the initially-designed pipe supporters, the rearrangement was suggested to improve the piping design.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.9
• /
• pp.50-55
• /
• 1998

A thermal printing head is used for heat transcription printing of facsimile or printer. The thermal printing head has multilayered thin films and heaters lined up. Thermal analysis of thermal printing head is important for a design of thermal printing head. Since the heating charateristics of thermal printing head is dependent on the thermal conductivities of multilayerd material, this study made numerical analysis for three dimensional transient heat conduction in mutilayered films by the finite difference method and investigated the effect of various thermal conductivities of thin films. The results of this study will be used to design thermal printing head and select the materials for thermal printing head.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.7
• /
• pp.117-125
• /
• 2004

Performing the sensitivity analysis of contact conduction on the basis of the thermal model already established, the study of thermal design is accomplished for the preparation of the future changes of mechanical interface design. A relatively simple thermal model is taken into consideration for the convenience of the analysis. A variety of the spacecraft bus voltages and the contact resistances are tried. As a consequence, when the mechanical interface condition is changed at the same module, the successful thermal design could be achieved if we design the heater to have sufficiently large power with reference to the heritage of contact resistance.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.173-178
• /
• 2011

Nowadays, SELENE-2 is under development for the moon explorer rover in Japan. AXS(Active X-ray Spectrometer) sensor development among the candidated payloads will be on going by the world-wide co-operation. The thermal design, analysis and test will be specially performed by Korean institutes. CFD techniques are used for the conceptual design and analysis. Thin-shell plate meshes being applied by Monte-Carlo Ray Tracing Method are generated for the thermal radiation analysis. Lumped capacity model is employed for the thermal conduction simulation of the AXS payload itself. Various shapes of the payload configuration with thermal boundary conditions are proposed and selected on the purpose of the analysis of the initial design. The results of the analysis are supposed to be used as the baseline for the further detailed design of the AXS payload in the future.