• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2099-2101
• /
• 2001

In general, the thermal control system has nonlinearity and the time delay, futhermore, it is difficult to design the free size controller, because the external environmental disturbances, such as rapid temperature change. Many researchers in this field are preferring to adapt the fuzzy logic control methods. But it is noted that the actuator identification of M.F.'s used in FLC is very difficult. Therefore in this paper, an implementation technique of thermal control system using RVEGA based optimal fuzzy control was proposed. It's superiority and exaction in controller design processes hardware in implementation were proved through a series of simulations and experimentations.

• Journal of Drive and Control
• /
• v.15 no.3
• /
• pp.43-48
• /
• 2018

The hydraulic control valve, used in the CPB (cold-pad-Batch) cold dyeing system, passes through a pressurized material that absorbs the dye. The hydraulic control of the hydraulic control panel shall be driven in a uniform and precisely controlled manner, as it interferes directly with the dyschromatism. In this study, an acceleration test model was employed to verify the durability of the hydraulic control of the hydraulic control panel, which was manufactured by the scenic model, and the pre-roll angle was analyzed before the performance of acceleration test. Based on the change in the amount of deformation of the padder roll the durability of the padder roll was analyzed along with verification of the durability of the skin and the rubber coating in contact with the fabric. Furthermore, the accelerated test method used for hydraulic controlled multi-cell padder rolls was verified.

• 한국전산유체공학회:학술대회논문집
• /
• 2004.10a
• /
• pp.131-136
• /
• 2004

Thermal control of satellite propellant tank is achieved by patch heaters enabled by thermostat's behavior. It is important to attach the thermostat on the appropriate position of the propellant tank. However its position cannot be given with exact numerics because tank is spherical. Actually the position for thermostat is designated in relevant drawing approximately, therby, the engineer practices depending on his own experience and intuition. The sensitivity analysis for the position of thermostat is performed such that the influence on the thermal behavior and control of tank is examined quantatively. When assembling tank module, the reasonable performance on the thermal control is believed with possible human errors if the uncertainty in the position of thermostat is not quite large.

• Computational Structural Engineering
• /
• v.7 no.3
• /
• pp.123-131
• /
• 1994

This paper is concerned with a new concept of vibration control in which thermal stresses are utilized. Thermal actuators are used to generate thermal stresses in a vibrating beam. The thermal actuators are found to work successfully as the control means. Especially the proposed control method in this paper can be effectively applied to the large space structures with low natural frequencies rather than to the structures with high natural frequencies. In the process of control design, various control methods including optimal-robust control method are investigated. Through numerical simulations, it is found that the robust-optimal control method can be efficiently with the vibration control of a cantilever beam using thermal stresses.

• Nuclear Engineering and Technology
• /
• v.38 no.2
• /
• pp.185-194
• /
• 2006

Transient operations for an integral type reactor, SMART-P, have been experimentally investigated using a thermal-hydraulic integral test facility, VISTA (Experimental Verification by Integral Simulation of Transients and Accidents), in order to verify the system design and performance of the SMART-P, a pilot plant of SMART. The VISTA facility was subjected to various accident conditions such as feedwater increase and decrease, loss of coolant flow, and control rod withdrawal accidents in order to elucidate the thermal-hydraulic responses following such accidents and finally to verify the system design of the SMARTP. Full functional control logics have been implemented in the VISTA facility in order to control the required control action for an accident simulation. As one of the sensitivity tests to verify the PRHRS performance, the effects of the initial water level in the compensation tank are experimentally investigated. When the initial water level is 16%, the water is quickly drained and nitrogen gas is then introduced into the PRHR system, resulting in deterioration of the PRHRS performance. It is thus found that nitrogen ingression should be prevented to ensure stable PRHRS operation.

• Journal of Aerospace System Engineering
• /
• v.7 no.3
• /
• pp.26-32
• /
• 2013

Passive attitude stabilization method has been widely usde for attitude determination and control of cube satellite due to its advantage of system simplicity. The permanent magnet installed on the cube satellite passively controls the attitude of the satellite such that the satellite is aligned with the earth magnetic field. In this paper, on-orbit thermal behavior of the cube satellite with the permanent magnet attitude stabilization method has been investigated through on-orbit thermal analysis. THe orbit profile obtained from the aforementioned attitude control method has been reflected in the analysis. The analysis results indicate that the thermal design proposed in this study is effective for satisfying the temperature requirements of the commericial mission equipments.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.04a
• /
• pp.24-24
• /
• 1999

This study addresses the effectiveness of TEC(Thermoelectric cooler) application for spacecraft thermal control. The required radiator area and power consumption characteristics of active thermal control using TEC are compared with the passive control at BOL and EOL through unsteady thermal analyses by calculating external heat fluxes. When the component operating temperature is low enough in TEC active control, the required radiator area can be smaller than the passive thermal control. TEC also needs less power consumption than the passive control under the condition that the temperature of cooling pars is low enough and/or the design temperature margin of the components is narrow enough.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.3 no.4
• /
• pp.257-262
• /
• 2002

A design method of a power controller for controlling the temperature adopted in RTP (rapid thermal processing) which uses the phase control method is presented. The power controller is fabricated by using the design method presented in this paper and is tested. As the results, the range of average voltage from the variable output is 0∼198.06 V and the control resolution is 48.356 mV (12 bit) at the range of the input signal (0∼10 V).

• Proceedings of the KSRS Conference
• /
• 2004.10a
• /
• pp.452-455
• /
• 2004

MSC (Multi-Spectral Camera) system is a remote sensing instrument to obtain high resolution ground image. EOS (Electro-Optic System) for MSC mainly consists of PMA (Primary Mirror Assembly), SMA (Secondary Mirror Assembly), HSTS (High Stability Telescope Structure) and DFPA (Detector Focal Plane Assembly). High performance of EOS makes it possible for MSC system to provide high resolution and high quality ground images. Temperature of the EOS needs to be controlled to be in a specific range in order not to have any thermal distortion which can cause performance degradation. It is controlled by full redundant CPU based electronics. The validity of thermistor readings can be checked because a few thermistors are installed on each control point on EOS. Various kinds of thermal control logics are used to prevent 'Single Point Failure'. Control logic has a few set of database in order not to be corrupted by SEU (Single Event Upset). Even though the thermal control logic is working automatically, it can also be monitored and controlled by ground-station operator. In this paper, various ways of thermal control logic for EOS in MSC will be presented, which include thermal control mode and logic, redundancy design and status monitoring and reporting scheme.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.70.2-70
• /
• 2002

In the thermal power plant, it is difficult to maintain strict control of the steam temperature in order to avoid thermal stress, because of variation of the heating value according to the fuel source, the time delay of changes in main steam temperature versus changes in fuel flow rate, difficulty of control on the main steam temperature control and the reheater steam temperature control system owing to the dynamic response characteristics of changes in steam temperature and the reheater steam temperature, fluctuation of inner fluid water and steam flow rates widely during load-following operation. Up to the present time, the PID controller has been used to operate this system...