평균입자크기가 서로 다른 WC-Co계 모재위에 고온 열처리법과 화학적 에칭방법을 이용하여 다이아몬드 막을 코팅하고 압흔법을 통해 그 접착력(adhesion strength)을 평가하였다. $1450^{\circ}C$의 고온 열처리 방법에 의해 준비된 WC-Co 시편표면에서는 WC 입자가 성장하였으며, 그 결과 20$\mu$m 이상의 다이아몬드 막이 증착된 경우에도 100kg의 하중에서도 우수한 접착력이 얻어졌다. 그러나, 모재 표면입자의 과도한 입성장으로 시편 인선부에는 변형이 발생하였으며, 증착된 다이아몬드 막은 거친 표면조도를 보였다. 이와 비교하여, 화학적 부식의 경우에는 submicron 크기의 WC 입자를 제외하고, 2$\mu$m 이상의 WC 입자를 가지는 모재를 이용하여 10$\mu$m의 다이아몬드 코팅막을 증착시킨 경우에는, 60kg의 하중에서도 양호한 접착력이 유지되었다 특히, WC 입자가 클수록 접착력의 신뢰성이 대폭 향상되었다. 이는 수 $\mu$m 이내의 비교적 얇은 두께의 다이아몬드 막을 증착하는 경우 화학적 에칭방법이 시편 형상의 변형을 방지하고, 양호한 표면조도를 얻을 수 있어 고온 열처리 방식에 비해 효과적임을 의미한다.
바이오가스는 Biomass, 유기성 폐기물 등의 혐기소화 공정을 통해 얻을 수 있는 대표적인 신재생연료로 저발열량에도 불구하고 탄소중립적인 특성이 있기 때문에 이를 엔진에 적용하여 에너지를 생산하고자 하는 노력이 계속되어왔다. 바이오가스는 원료의 종류 및 혐기소화 공정 조건에 따라 그 연료 조성이 달라질 수 있는데, 이러한 조성 변화는 엔진 성능에 큰 영향을 미칠 수 있기 때문에 이에 대한 연구가 필요한 실정이다. 따라서 이번 연구에서는 다양한 발열량을 갖는 바이오가스를 연료 내 불활성가스 비율을 변화시켜 모사하고 이를 이용하여 바이오가스 내 불활성가스 비율의 변화, 즉 발열량의 변화가 엔진 성능 및 배기 특성에 주는 영향을 파악하였다. 실험결과로 각 불활성가스 함량에 따른 최적 점화시기를 결정하였으며, 발열량 변화가 엔진 출력, 효율, 배기 성능에 미치는 영향을 제시하였다.
The purpose of this paper is to present the manufacturing defect and damage pattern of a 3 phase 22.9/3.3kV oil immersed transformer, as well as to present an objective basis for the prevention of a similar accident and to secure data for the settlement of PL related disputes. It was found that in order to prevent the occurrence of accidents to transformers, insulating oil analysis, thermal image measurement, and corona discharge diagnosis, etc., were performed by establishing relevant regulation. The result of analysis performed on the external appearance of a transformer to which an accident occurred, the internal insulation resistance and protection system, etc., showed that most of the analysis items were judged to be acceptable. However, it was found that the insulation characteristics between the primary winding and the enclosure, those between the ground and the secondary winding, and those between the primary and secondary windings were inappropriate due to an insulating oil leak caused by damage to the pressure relief valve. From the analysis of the acidity values measured over the past 5 years, it is thought that an increase in carbon dioxide (CO2) caused an increase in the temperature inside the transformer and the increase in the ethylene gas increased the possibility of ignition. Even though 17 years have passed since the transformer was installed, it was found that the system's design, manufacture, maintenance and management have been performed well and the insulating paper was in good condition, and that there was no trace of public access or vandalism. However, in the case of transformers to which accidents have occurred, a melted area between the upper and the intermediate bobbins of the W-phase secondary winding as well as between its intermediate and lower bobbins. It can be seen that a V-pattern was formed at the carbonized area of the transformer and that the depth of the carbonization is deeper at the upper side than the lower side. In addition, it was found that physical bending and deformation occurred inside the secondary winding due to non-uniform pressure while performing transformer winding work. Therefore, since it is obvious that the accident occurred due to a manufacturing defect (winding work defect), it is thought that the manufacturer of the transformer is responsible for the accident and that it is lawful for the manufacture to investigate and prove the concrete cause of the accident according to the Product Liability Law (PLL).
Park, Yong-Jin;Park, Won-Joo;Yim, Sung-Hyuk;Yang, Seong-Jun;Sun, Yuan Lu;Jeong, Ji-Hoon;Park, Eon-Sub
Biomolecules & Therapeutics
/
제15권1호
/
pp.58-64
/
2007
The previous study reported the biological effect of magnetic field exerted by acting on endocrine and anti-oxidant system. The present study aims to study whether ELF-MF (extremely low frequency magnetic field) affects the physiological endocrine systems such as thyroid and whether ELF-MF affects the defense system against oxidative stress when it alters the function of thyroid. Finally, we correlate the effects of MF on oxidative stress, and adrenal and thyroid with an environmental stress factor. We exposed sham or MF to rats for 5 or 25 days. After the exposure, we determined pain sensitivity, level of TSH, $T_3$ and free $T_4$ in plasma. We also assayed in whole brain, lipid peroxidation, the activity of enzymatic anti-oxidant defense including superoxide dismutase(SOD) and glutathione peroxidase (GPx), and non enzymatic defense such as reduced or oxidized glutathione contents. MF induced the hypersensitivity to thermal stimuli with the reduction of latency. $T_3$ and $T_4$ levels were also increased by the exposure of MF. In addition, we observed the rise of MDA level in rat brain by MF although the MF did not change superoxide dismutase and glutathione peroxidase activity. The effect of MF on both reduced and oxidized glutathione results in decrease in reduced or oxidized glutathione in whole brain. In every experiment, there was no significant difference in MF influence between short term (5 days) and long term (25 days) exposure. Taken together, MF exposure affects the thyroid hormonal control in brain. The elevated thyroid hormone acts on brain, leading to hyper-utilization of oxygen. This phenomenon may be correlated with oxidative stress resulting from MF exposure. In conclusion, we suggest that MF exposure may be an environmental stress by exerting oxidative stress.
최근 디지털 방사선 영상획득을 위한 평판형 X선 검출기에 이용되는 광도전체(a-Se, $HgI_2$, PbO, CdTe, $PbI_2$ 등)에 대한 관심이 증대되고 있다. 본 연구에서는 $HgI_2$ 와 a-Se 필름 변환체에 대해 X선에 대한 전기적 신호검출 특성을 조사하였다. 수백 마이크로의 두꺼운 광도전체 필름 제작을 위해 $HgI_2$는 입자침전방법을 이용하였고, a-Se은 종래의 진공열증착법을 이용하였다. 제작된 시편에 대한 전기적 특성 실험은 누설전류, 신호응답 특성, 민감도 등을 측정하였다. 실험결과로부터, $HgI_2$는 상용화된 a-Se에 비해 낮은 동작전압특성과 우수한 신호 발생율을 보임을 알 수 있었다.
We have recently reported that the continuous exposure of rats to a concrete building environment under cool temperatures had adverse effects on general health parameters and embryo-fetal development. This study examined to compare the potential effects of concrete and wood building environments on pregnant dams and embryo-fetal development in rats. Groups of 10 mated females were exposed to polycarbonate (control), concrete, or wood cages from gestational days (GD) 0 to 20 under cool temperatures $(11.9\sim12.3^{\circ}C)$. All the females underwent a caesarean section on GD 20, and their fetuses were examined for any morphological abnormalities. The temperatures in the cages were similar in all groups but the relative humidity in the concrete and wood groups were higher than in the control group. The concentration of volatile organic compounds in the wood group was higher than in the control group. In the concrete group, maternal effects manifested as an increase in the incidence of clinical signs, a lower body weight, and a decrease in the thymus and ovary weights. Developmental effects included increased post-implantation loss and decreased litter size. Infrared thermal analysis showed that the skin temperature of the rats in the concrete group was lower than that in the control group. In contrast, there were no exposure-related adverse effects on the maternal and developmental parameters in the wood group. Overall, the exposure of pregnant rats to a concrete building environment under cool temperatures has adverse effects on the clinical signs, body weight, skin temperature, organ weight, and embryo-fetal development. On the other hand, exposure to a wood building environment does not have any adverse effects in rats.
The increasing interest in light weight materials coupled to the need for cost -effective processing have combined to create a significant opportunity for aluminum P/M. particularly in the automotive industry in order to reduce fuel emissions and improve fuel economy at affordable prices. Additional potential markets for Al PIM parts include hand tools. Where moving parts against gravity represents a challenge; and office machinery, where reciprocating forces are important. Aluminum PIM adds light weight, high compressibility. low sintering temperatures. easy machinability and good corrosion resistance to all advantages of conventional iron bm;ed P/rv1. Current commercial alloys are pre-mixed of either the AI-Si-Mg or AL-Cu-Mg-Si type and contain 1.5% ethylene bis-stearamide as an internal lubricant. The powder is compacted in closed dies at pressure of 200-500Mpa and sintered in nitrogen at temperatures between $580~630^{\circ}C$ in continuous muffle furnace. For some applications no further processing is required. although most applications require one or more secondary operations such as sizing and finishing. These sccondary operations improve the dimension. properties or appearance of the finished part. Aluminum is often considered difficult to sinter because of the presence of a stable surface oxide film. Removal of the oxide in iron and copper based is usually achieved through the use of reducing atmospheres. such as hydrogen or dissociated ammonia. In aluminum. this occurs in the solid st,lte through the partial reduction of the aluminum by magncsium to form spinel. This exposcs the underlying metal and facilitates sintering. It has recently been shown that < 0.2% Mg is all that is required. It is noteworthy that most aluminum pre-mixes contain at least 0.5% Mg. The sintering of aluminum alloys can be further enhanced by selective microalloying. Just 100ppm pf tin chnnges the liquid phase sintering kinetics of the 2xxx alloys to produce a tensile strength of 375Mpa. an increilse of nearly 20% over the unmodified alloy. The ductility is unnffected. A similar but different effect occurs by the addition of 100 ppm of Pb to 7xxx alloys. The lend changes the wetting characteristics of the sintering liquid which serves to increase the tensile strength to 440 Mpa. a 40% increase over unmodified aIloys. Current research is predominantly aimed at the development of metal matrix composites. which have a high specific modulus. good wear resistance and a tailorable coefficient of thermal expnnsion. By controlling particle clustering and by engineering the ceramic/matrix interface in order to enhance sintering. very attractive properties can be achicved in the ns-sintered state. I\t an ils-sintered density ilpproaching 99%. these new experimental alloys hnve a modulus of 130 Gpa and an ultimate tensile strength of 212 Mpa in the T4 temper. In contest. unreinforcecl aluminum has a modulus of just 70 Gpa.
신규 살충제인 KH-502의 안전성을 조사하기 위하여 다양한 조건하에서 광(光) 분해(分解) 실험을 수행하였다. 이 실험에서 KH-502를 acetone 또는 acetonitrile 용액에 첨가한 뒤 태양광선 또는 자외선 $(300{\sim}350nm)$을 조사(照射)하였고, acetone 또는 acetonitrile 용액에는 수분함량, 산소함량이 달랐으며, 부식산,rosebengal 또는 tryptophan이 첨가 되었다. KH-502의 안전성 및 분해경향에 대한 결과를 요약하면 다음과 같다. 1. KH-502의 광분해(光分解)는 자외선을 조사(照射)한 경우와 그렇치 않은 경우에 매우 유의성있는 차이를 보여 주었다. KH-502는 acetone 용매에서 광관여효과에 의해 광분해(光分解)되었으나, acetonitrile 용매 하(下)에서는 광분해되지 않았다. 2. KH-502의 광분해 경향은 열 분해 경향과 판이하게 달랐으며, 광분해산물은 KH-502 oxo형, S-ethyl KH-502, PTMHP 및 몇가지 미지물질 등이었다. 3. acetone 또는 acetonitrile에 첨가된 부식산, rosebengal, tryptophan은 KH-502의 광분해에 광관여효과를 나타내지 않았다. acetone 용매의 용존산소는 acetone과 함께 경쟁적으로 광관여효과를 나타내어 KH-502의 분해를 촉진시켰다. 4. acetone 용매를 부식산 또는 논물로 처리했을때, KH-502의 광분해는 감소하였다.
현재 개발되고 있는 수소 압축 사이클에서는 압축기를 통해 초고압으로 압축된 수소를 고압용기 내에 저장하여 사용한다. 이러한 충전과정 중 용기내의 수소의 압력 및 온도 상승으로 인하여 고압용기에서 열응력이 발생할 수 있다. 고압용기의 신뢰성을 확보하기 위해서는 용기내의 수소의 온도를 예측하고 제어하는 것이 중요하다. 본 논문에서는 이러한 고압용기의 신뢰성 해석을 위하여 50 MPa급 수소압축시스템에서 고압용기를 충전하는 과정에서의 압력상승에 따른 용기 내의 수소온도 변화 및 외부와의 열평형까지 걸리는 시간, 감압밸브를 지날 때의 수소온도 변화, 고압용기 냉각을 위한 열교환기의 요구능력 등에 대하여 이론적인 방법과 수치적인 방법으로 해석을 수행하였다. 이론해석 결과, 고압용기의 내부 온도는 충전하기 전에 40 ℃에서 충전 후 1st cycle, 2nd cycle에서 평균적으로 126.675 ℃, 62.1 ℃가 증가하였다. 또한, 고압용기의 충전량은 1st cycle, 2nd cycle에서 각각 7.9 kg, 8.9 kg으로 계산되었다. 본 연구의 결과는 수소충전소와 같이 수소압축시스템이 필요한 현장의 인프라 설계 및 구축 등에 유용하게 활용 될 것이다.
해저터널은 시공중 예측치 못한 고수압으로 인한 해수 침투가 발생할 가능성이 매우 크다. 이에 고수압조건에서 차수 및 보강효과가 탁월한 인공 동결 공법의 적용이 대두되고 있다. 본 연구에서는 인공 동결 공법에 필요한 냉매량을 산정하기 위해 열흐름 에너지 이론 모델에 의한 이론적인 값을 계산하고, 동결 챔버 실험결과 및 수치해석결과와의 비교를 통해 적정성을 검증하였다. 염분과 수압에 따른 열적 역학적 특성 변화를 규명하기 위해 동결용 챔버를 제작하여 염분과 수압 조건에 따라 사질토의 동결 시간을 파악하였다. 또한, 이론값과 수치해석 결과의 동결 시간은 유사한 경향을 확인하였다. 동결공법의 냉매량은 수치해석의 결과를 기반으로, 동결 챔버 실험을 통해 동결 효율의 결과와 이론식을 통한 동결 유지를 위한 에너지 비율을 적용하여 산정하였다. 동결유지를 위한 에너지 비율은 해저터널의 토피고와 해저면의 수온에 따라 좌우될 것으로 판단된다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.