• International Journal of Fluid Machinery and Systems
• /
• 제5권3호
• /
• pp.134-142
• /
• 2012

The competition to deliver ultra-low emitting vehicles at a reasonable cost is driving the automotive industry to invest significant manpower and test laboratory resources in the design optimization of increasingly complex exhaust after-treatment systems. Optimization can no longer be based on traditional approaches, which are intensive in hardware use and laboratory testing. The CFD is in high demand for the analysis and design in order to reduce developing cost and time consuming in experiments. This paper describes the development of a comprehensive practical model based on experiments for simulating the performance of automotive three-way catalytic converters, which are employed to reduce engine exhaust emissions. An experiment is conducted to measure species concentrations before and after catalytic converter for different loads on engine. The model simulates the emission system behavior by using an exhaust system heat conservation and catalyst chemical kinetic sub-model. CFD simulation is used to study the performance of automotive catalytic converter. The substrate is modeled as a porous media in FLUENT and the standard k-e model is used for turbulence. The flow pattern is changed from axial to radial by changing the substrate model inside the catalytic converter and the flow distribution and the conversion efficiency of CO, HC and NOx are achieved first, and the predictions are in good agreement with the experimental measurements. It is found that the conversion from axial to radial flow makes the catalytic converter more efficient. These studies help to understand better the performance of the catalytic converter in order to optimize the converter design.

• 한국세라믹학회지
• /
• 제38권11호
• /
• pp.1000-1007
• /
• 2001

진공관형 태양열 집열기에서는 열관(heat pipe)과 붕규산염 유리관의 안정된 접합이 이를 장시간 사용하는데 매우 중요하다. 구리와 유리는 그 물리.화학적 성질에 큰 차이가 있어 접합하기가 어려움으로 구리관 표면에 유리와 화학적 결합이 용이한 산화막을 생성시켜 접합하도록 구리의 산화상태, 접합계면 및 접합강도를 XRD, SEM, EDS 및 인정시험기로 측정하였다. 순수 구리는 $600^{\circ}C$ 이하로 열처리하였을 때 Cu$_2$O 산화막을 생성하였으나 그 이상의 온도에서는 CuO 산화막을 형성하였으며 후자의 산화막은 구리와의 접합력이 매우 불량하였다. 그러나 붕사로 표면 처리를 하였을 경우에는 80$0^{\circ}C$에서도 Cu$_2$O 산화막 만이 발견되었다. Cu$_2$O 산화막을 생성시킨 구리관과 붕규산염 유리관을 Housekeeper법으로 접합하였을 경우 354.4N의 접합강도를 얻을 수 있었으며 열충격 저항성도 매우 뛰어났다.

• 한국표면공학회지
• /
• 제42권1호
• /
• pp.1-7
• /
• 2009

Resistive heating sources are widely used to prepare thin films by vapor deposition because they are cheap, and easy to install and handle in vacuum system. Graphite is one of materials used to make the resistive heating source, but until now only limited applications have been possible as it reacts easily with evaporating materials at high temperature. In this study, evaporation characteristics of aluminum have been investigated by using graphite boat thermally treated with BN powder. The employed graphite boat has been prepared by spray-coating BN power onto the cavity surface of the boat and thermal treatment with aluminum in vacuum at the temperature of more than $1400^{\circ}C$. The voltage-current characteristics as well as resistivity changes of the graphite boat have been investigated during aluminum evaporation according to the applied voltage and time. The evaporation aspect has been picturized during flash evaporation for 40 seconds based on the characterization results. The evaporation rate of the graphite boat has been compared with that of BN boat. The graphite boat showed some different characteristics compared with BN boat, in that the evaporation occurred at the last stage of flash evaporation. The film appearance according to the applied voltage has been compared, and also the reflectance of the resulting film has been investigated according to the film thickness. It has been found that the graphite boat thermally treated with BN powder can be used for aluminum evaporation without problem.

• 한국세라믹학회지
• /
• 제42권11호
• /
• pp.729-736
• /
• 2005

HTGR (High Temperature Gas-cooled Reactor) is spotlighted to next generation nuclear power plant for producing the clean hydrogen gas and the electricity. In this study, the spherical $UO_3$ gel particles were prepared by the external gelation process, and the characteristics of these particles were analyzed the particle shape, composition of precipitate, and thermal decomposition characteristics with the Streoscope, FT-IR, and X-ray diffractometer. Raw material of the ADUN (Acid Deficient Uranyl Nitrate) solution, which has [$NO_3$]/[U] mole ratio = 1.75, was obtained from dissolution of the $U_{3}O_{8}$ powder with concentrated $HNO_3$, and its concentration is 3.5 M-U/l. The broth solution is prepared with the ADUN, urea, PVA, and THFA solution. The droplets of the broth solution was made through a nozzle system. From this study, we obtained the following results; 1) an externel chemical gelation process is a suitable method in the spherical $UO_3$ particle production, 2) the particle shape are changed by an urea mixing time, THFA volume, and the viscosity of the broth solution, 3) the amorphous $UO_3$ particles obtained from these experiments was converted to $U_{3}O_{8}$ and then $UO_2$ by heat treatment in hydrogen atmosphere at $600^{\circ}C$.

• Journal of Acupuncture Research
• /
• 제18권6호
• /
• pp.171-187
• /
• 2001

Objective : Moxibustion has been proved efficacious for many diseases, but isn't widespread in the clinics due to a danger of skin burning, the smoke produced while burning a moxa combustion and so on. Therefore, another type of moxa that can be resolved these troubles is required. To improve the effect of moxibustion and develop the new thermal stimulating treatment, the performance of commercial moxibustion widely used are studied systematically and found out quantitatively. Methods : We have selected two types (small-size moxa A(sMA), small-size moxa B (sMB)) among small-size moxaes used widely in the clinic. We examined combustion time, various temperatures, temperature gradient in each period during a combustion of moxa. Results : 1. The combustion time in the preheating period appeared somewhat longer in sMA than in sMB. 2, The combustion time in the heating period appeared longer in sMA by 26% than in sMB. 3. The average temperature in the heating period was $37.6{\sim}37.8^{\circ}C\;in\;sMA\;and\;36.2{\sim}36.8^{\circ}C$ in sMB and the maximum temperature measured at a center of contact surface in sMA was $48.6^{\circ}C$, higher by over $2.8^{\circ}C$ than that of sMB moxibustion. 4. The average ascending temperature gradient in the heating period was $0.08{\sim}0.1^{\circ}C/sec$ in both moxaes, and the average ascending temperature gradient of heating period in sMB appeared larger. The maximum ascending temperature gradient appeared higher in sMB, and the time reaching maximum ascending temperature gradient appeared much earlier in sMA than in sMB. 5. The combustion time in the retaining period was around 100 sec in sMA and around 275 sec in sMB. 6. The average temperature in the retaining period was $42.2{\sim}46.0^{\circ}C\;in\;sMA\;and\;39.3{\sim}41.4^{\circ}C/sec$ in sMB. The minimum temperature in the retaining period was over $38.80^{\circ}C$ in sMA but just $34.7^{\circ}C$ in sMB. 7. The average descending temperature gradient in sMA was $-0.050{\sim}0.067^{\circ}C/sec$ and in sMB was $-0.030{\sim}0.037^{\circ}C/sec$ 8. The combustion time in the cooling period appeared longer over two times in sMA than in sMB, and the time which the cooling period (minimum temperature) finished at appeared later in sMB by 55 sec. 9. We classified the combustion process that the measured temperature rose over body heat($37^{\circ}C$) into the effective combustion period. The effective combustion time was 233.3 sec in sMA and 300.4 sec in sMB respectively, and was longer by about 29% in sMB. The average temperature and maximum temperature in the effective combustion time appeared higher in sMA. The time taken until the maximum temperature was reached was 225.1 sec in sMA and 244.5 sec in sMB, faster by about 20 sec in sMA. The maximum ascending temperature gradient during the effective combustion period appeared larger about 1.4 times in sMB, but the time when the maximum ascending temperature gradient happened was faster in sMA. Conclusion : It appears that sMB, compared with sMA, is proper if necessary to apply the long time and weak stimulus, because of the gentle stimulus during the relatively longer time. In contrast, sMA that the symmetrical combustion happened is proper if necessary to apply the short time and strong stimulus.

• 한국전기전자재료학회논문지
• /
• 제24권5호
• /
• pp.392-397
• /
• 2011

The effect of various post-annealing temperature to sputtered Pb(Zr,Ti)$O_3$ (PZT) thin films was investigated. The crystallization process, surface morphology and the electrical characteristics strongly depends on the rapid thermal annealing (RTA). In radio frequency (RF) sputtering methods, there were many papers mostly forcing on the crystal forming and the surface variations with different elements distribution (Pb, Ti, Zr, O) on the surface of the PZT layer. In this experiment, the post-annealing treatment promoted the Pb volatilization in PZT thin film and affected the Ti diffused throughout the Pt layer into the PZT layer. Second ion mass spectroscopy (SIMS) analysis was employed to show that the Pb element in the PZT layer was decreased at the same time the Ti element mass was slight decreased than Pb with increasing RTA temperature. That result prove the content of Pb affect the PZT thin film property.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 C
• /
• pp.1629-1630
• /
• 2006

This paper describes a micro total analysis system ($\mu$ TAS) for detecting and digesting the target protein which includes a bead based temperature controllable microchip and computer based controllers for temperature and valve actuation. We firstly combined the temperature control function with a bead based microchip and realized the on-chip sequential reactions using two kinds of beads. The PEG-grafted bead, on which RNA aptamer was immobilized, was used for capturing and releasing the target protein. The target protein can be chosen by the type of RNA aptamer. In this paper, we used the RNA aptamer of HCV replicase. The trypsin coated bead was used for digesting the released protein prior to the matrix assisted laser desorption ionization time of flight mass spectrometer (MALDI TOF MS). Heat is applied for release of the captured protein binding on the bead, thermal denaturation and trypsin digestion. PDMS microchannel and PDMS micro pneumatic valves were also combined for the small volume liquid handling. The entire procedures for the detection and the digestion of the target protein were successfully carried out on a microchip without any other chemical treatment or off-chip handling using $20\;{\mu}l$ protein mixture within 20 min. We could acquire six matched peaks (7% sequence coverage) of HCV replicase.

• 한국결정성장학회지
• /
• 제31권2호
• /
• pp.89-95
• /
• 2021

현재 리튬이온 배터리에 사용되는 고니켈계 양극재의 수요 증대에 따라 수산화리튬(LiOH) 제조 연구가 활발히 진행되고 있다. 본 논문에서는 탄산리튬(Li2CO3)으로부터 수산화리튬의 제조를 위하여, 탄산리튬의 열분해를 통한 산화리튬(Li2O)의 전환 공정에 대해 연구하였다. 열처리 시 탄산리튬과 알루미나, 석영 그리고 흑연 도가니 사용에 따른 반응 메커니즘을 확인하였으며, 흑연 도가니를 사용했을 경우 온전한 산화리튬 분말을 얻었다. TG 분석 결과를 바탕으로 열처리 온도를 700℃, 900℃ 그리고 1100℃로 설정하였으며 유지시간 및 분위기를 제어하여 시약급 탄산리튬의 열처리를 진행하였다. XRD 분석 결과, 제조된 산화리튬은 질소 분위기에서 1시간 동안 1100℃의 온도로 열처리를 하였을 때 높은 결정성을 보였다. 또한 수산화리튬으로 전환하기 위해 시약급 산화리튬을 100℃에서 수반응하였다. XRD 분석을 통해 수산화리튬(LiOH)과 수산화리튬 일수화물(LiOH·H2O)이 생성됨을 확인하였다.

• Preventive Nutrition and Food Science
• /
• 제4권1호
• /
• pp.6-13
• /
• 1999

The quality of the buckwheat bread made with previously heated ($55^{\circ}C$) and cooled buckwheat flour 0dough with the addition of ascorbic acid(AA) or/and sodium stearoyl lactylate(SSL) was evaluated . With heat treatemtn , handling property of dough and grain of the bread crumb were markedly improved and stickiness of the dough decreased . The optimum resting time to produce the best loaf volume and grain was found to be 3hr for both unheated and heated doughs. Heat treated dough showed higher dough expansion rate during fermentation than unheated dough, even though heated dough had lower loaf volume, probably because of an improper oven spring. Increase in shortening of dough formula from 3% to 5% improved loaf volume without improvement of handling property. With the addition of 100 ppm AA or/and 0.5% SSL, loaf volume and crumb grain were improved for both unheated and heated doughs.Microscopic analysis of a mixed dough by scanning electron microscope (SEM) showed that heated dough had a continuous network whereas unheated dough was discontinuous. The addition of AA and SSL gave the dough a more continuous network whereas unheated dough was discontinuous . The addition of AA and SSL gave the dough a more continuous structure with strengthened strands or interactions between the starch granule and protein. Therefore, it appears that the presence of continuity in heated buckwheat breadwheat bread dough is related to the improved loaf volume and crumb grain without dough stickness.

• The Journal of Advanced Prosthodontics
• /
• 제12권3호
• /
• pp.140-149
• /
• 2020

PURPOSE. This study evaluated the color stabilities of two computer-aided design and computer-aided manufacturing (CAD/CAM) blocks and a nanofill composite resin and the microtensile bond strength (µTBS) between the materials. MATERIALS AND METHODS. Twelve specimens of 4 mm height were prepared for both Lava Ultimate (L) and Vita Enamic (E) CAD/CAM blocks. Half of the specimens were thermocycled (10,000 cycle, 5° to 55℃) for each material. Both thermocycled and non-thermocycled specimens were surface treated with one of the three different methods (Er,Cr:YSGG laser, bur, or control). For each surface treatment group, one of the thermocycled and one of non-thermocycled specimens were restored using silane (Ceramic Primer II), universal adhesive (Single Bond Universal), and nanofill composite resin of 4-mm height (Filtek Ultimate). The other specimens were restored with the same procedure without using silane. For each group, 1 × 1 × 8 mm bar specimens were prepared using a microcutting device. Bar specimens were thermocycled (10,000 cycle, 5° to 55℃) and microtensile tests were performed. Staining of the materials in coffee solution was also compared using a spectrophotometer. Data were analyzed using one-way ANOVA, t-test and post-hoc Scheffe tests. RESULTS. µTBS were found similar between the thermocycled and non-thermocycled groups (P>.05). The highest µTBS (20.818 MPa) was found in the non-thermocycled, bur-ground, silane-applied E group. Silane increased µTBS at some E groups (P<.05). Composite resin specimens showed more staining than CAD/CAM blocks (P<.05). CONCLUSION. CAD/CAM blocks can be repaired with composite resins after proper surface treatments. Using silane is recommended in repair process. Color differences may be shown between CAD/CAM blocks and the nanofill composite after a certain time period.