• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.719-722
• /
• 2003

Ferroelectric $Pb(Zr_{1-x}Ti_x)O_3$ (PZT) films were deposited on (001) MgO single crystals using sol-gel method. Structural properties and surface morphologies of PZT films were investigated using an X-ray diffractometer and a scanning electron microscopy, respectively. The dielectric properties of PZT films were investigated with the dc bias field using interdigitated capacitors (IDC) which were fabricated on PZT films using a thick metal layer by photolithography and dry etching process. The small signal dielectric properties of PZT films were calculated by a modified conformal mapping method with low and high frequency data, such as capacitance measured by an impedance gain/phase analyzer at 100 kHz and reflection coefficient (S-parameter) measured by a HP 8510C vector network analyzer at 1 -20 GHz. The IDC on PZT films exhibited about 67% of capacitance change with an electric field of 135 kV/cm at 10 GHz. These PZT thin films can be applied to tunable microwave devices such as phase shifters, tunable resonators and tunable filters.

• Structural Engineering and Mechanics
• /
• 제63권6호
• /
• pp.713-723
• /
• 2017

As a new type of ballastless track, longitudinal continuous slab track (CST) has been widely used in China. It can partly isolate the interaction between the ballastless track and the bridge and thus the rail expansion device would be unnecessary. Compared with the traditional track, CST is composed of multi layers of continuous structures and various connecting components. In order to investigate the performance of CST on a long-span bridge, the spatial finite element model considering each layer of the CST structure, connecting components, bridge, and subgrade is established and verified according to the theory of beam-rail interaction. The nonlinear resistance of materials between multilayer track structures is measured by experiments, while the temperature gradients of the bridge and CST are based on the long-term measured data. This study compares the force distribution rules of ballasted track and CST as respectively applied to a long span bridge. The effects of different damage conditions on CST structures are also discussed. The results show that the additional rail stress is small and the CST structure has a high safety factor under the measured temperature load. The rail expansion device can be cancelled when CST is adopted on the long span bridge. Beam end rotation caused by temperature gradient and vertical load will have a significant effect on the rail stress of CST. The additional flexure stress should be considered with the additional expansion stress simultaneously when the rail stress of CST requires to be checked. Both the maximum sliding friction coefficient of sliding layer and cracking condition of concrete plate should be considered to decide the arrangement of connecting components and the ultimate expansion span of the bridge when adopting CST.

• Geomechanics and Engineering
• /
• 제33권1호
• /
• pp.11-18
• /
• 2023

This study explores a new energy partitioning approach to determine the fracture toughness of 3-D printed pristine/recycled high density polyethylene (HDPE) blends employing the essential work of fracture (EWF) concept. The traditional EWF approach conducts a uniaxial tensile test with double-edge notched tensile (DENT) specimens and measures the total energy defined by the area under a load-displacement curve until failure. The approach assumes that the entire total energy contributes to the fracture process only. This assumption is generally true for extruded polymers that fracture occurs in a material body. In contrast to the traditional extrusion manufacturing process, the current 3-D printing technique employs fused deposition modeling (FDM) that produces layer-by-layer structured specimens. This type of specimen tends to include separation energy even after the complete failure of specimens when the fracture test is conducted. The separation is not relevant to the fracture process, and the raw experimental data are likely to possess random variation or noise during fracture testing. Therefore, the current EWF approach may not be suitable for the fracture characterization of 3-D printed specimens. This paper proposed a new energy partitioning approach to exclude the irrelevant energy of the specimens caused by their intrinsic structural issues. The approach determined the energy partitioning location based on experimental data and observations. Results prove that the new approach provided more consistent results with a higher coefficient of correlation.

• 마이크로전자및패키징학회지
• /
• 제13권2호
• /
• pp.1-7
• /
• 2006

본 논문에서는 솔더 레지스트(solder resist)의 두께와 코어의 물성에 따른 인쇄회로기판의 철의 크기와 형상에 대하여 연구하였다. 인쇄회로기판의 굽힘 변형은 적층되는 재료의 열팽창계수의 차이에 의해 발생한다. 따라서 굽힘 변형의 감소를 위해서는 열팽창계수의 차이가 작은 적층 재료를 사용하는 것이 필요하며, 구조 형상에서도 상면과 하면의 불균일성을 완화시킬 필요가 있다. 또한, 적층 재료에서 코어의 강성을 높여 점의 발생을 억제할 수 있다. 코어를 이루는 복합재료는 적층 순서와 섬유 각에 따른 물성 특성의 방향성에 따라 굽힘과 비틀림이 연성되는 현상을 보이며, 이와 같은 성질을 이용하면 휨을 제어할 수 있다. 본 연구에서는 2층으로 구성된 chip scale package (CSP) 기판의 휨에 대한 연구로, 실험 및 유한 요소해석 툴을 이용하여 개선 결과를 도출하였다.

• Current Photovoltaic Research
• /
• 제5권1호
• /
• pp.15-19
• /
• 2017

The fossil fuel power consumption generates $CO_2$, which causes the problems such as global warming. Also, the increase in energy consumption has accelerated the depletion of the fossil fuels, and renewable energy is attracting attention. Among the renewable energies, the solar energy gets a lot of attention as the infinite clean energy source. But, the supply level of solar cell is insignificant due to high cost of generation of electric power in comparison with fossil fuels. Thus several researchers are recently doing the research on ultra-low-cost solar cells. Also, $Cu_2O$ is one of the applied materials as an absorption layer in ultra-low-cost solar cells. Cuprous oxide ($Cu_2O$) is highly desirable semiconductor oxide for use in solar energy conversion due to its direct band gap ($E_g={\sim}2.1eV$) and a high absorption coefficient that absorbs visible light of wavelengths up to 650 nm. In addition, $Cu_2O$ has several advantages such as non-toxicity, low cost and can be prepared with simple and cheap methods on large scale. In this work, we fabricated the $Cu_2O$ thin films by reactive sputtering method. The films were deposited with a Cu target with variable parameters such as substrate temperature, rf-power, and annealing condition. Finally, we confirmed the structural properties of thin films by XRD and SEM.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.19-19
• /
• 2009

TiNxOy/TiNx multilayer thin films with a high resistance (~ k$Omega$) were deposited on SiO2/Si substrates at room temperature by sputtering. The TiNx thin films show island and smooth surface morphology in samples prepared by dc and rf magnetron sputtering, respectively. TiNxOy/TiNx multilayer has been developed to control temperature coefficient of resistance (TCR) by the incorporation of TiNx layer (positive TCR) inserted into TiNxOy layers(negative TCR). Electrical and structural properties of sputtered TiNxOy/TiNx multilayer films were investigated as a function of annealing temperature. In order to achieve a stable high resistivity, multilayer films were annealed at various temperatures in oxygen ambient. Samples annealed at 700 oC for 1 min exhibit a good TCR value and a stable high resistivity.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.335-335
• /
• 2011

Instability of a thin film attached to a compliant substrate often leads to emergence of exquisite wrinkle patterns with length scales that depend on the system geometry and applied stresses. However, the patterns that are created using the current techniques in polymer surface engineering, generally have low aspect ratio of undulation amplitude to wavelength, thus, limiting their application. Here, we present a novel and effective method that enables us to create wrinkles with a desired wavelength and high aspect ratio of amplitude over wavelength as large as to 2.5:1. First, we create buckle patterns with high aspect ratio of amplitude to wavelength by deposition of an amorphous carbon film on a surface of a soft polymer poly(dimethylsiloxane) (PDMS). Amorphous carbon films are used as a protective layer in structural systems and biomedical components, due to their low friction coefficient, strong wear resistance against, and high elastic modulus and hardness. The deposited carbon layer is generally under high residual compressive stresses (~1 GPa), making it susceptible to buckle delamination on a hard substrate (e.g. silicon or glass) and to wrinkle on a flexible or soft substrate. Then, we employ glancing angle deposition (GLAD) for deposition of a high aspect ratio patterns with amorphous carbon coating on a PDMS surface. Using this method, pattern amplitudes of several nm to submicron size can be achieved by varying the carbon deposition time, allowing us to harness patterned polymers substrates for variety of application. Specifically, we demonstrate a potential application of the high aspect wrinkles for changing the surface structures with low surface energy materials of amorphous carbon coatings, increasing the water wettability.

• 조명전기설비학회논문지
• /
• 제13권1호
• /
• pp.53-59
• /
• 1999

$(Ba_{0.85}Ca_(0.15)TiO_3+ZnO$ 세라믹 커패시터는 ZnO를 0.1~0.4몰로 변화시켜 시편을 제조하였다. 본 연구에서는 고전압용 세라믹 커패시터의 구조적 및 전기적 특성에 관하여 연구하였다. 세라믹 커패시터의 상대밀도는 모든시료에서 높았다. 입자의 크기는 $1.0~1.22[\mum]$ 정도의 작은 크기이었으며 ZnO의 첨가량이 0.3몰일 때 가장 크게 성장하였다. 입자의 크기가 클 때 시정수는 증가하였다. 세라믹 커패시터의 온도계수는 0.12~10[kHz]에서 100[ppm]이하로 온도변화에 대해 유전율이 안정하였다. 유전 완화시간은 $[110^{\circ}C]$이상에서 계면분극의 영향으로 감소하였으며 $110[^{\circ}C]$이하에서는 상유전층의 공간전하 분극에 의해서 유전 완화시간이 증가하였다. 유전특성에 영향을 주는 절연층의 두께가 ZnO에 의해서 증가하였으며 유전율의 변화는 0.1[%]로 전압의 변동에 대해 유전율이 안정하였다.

• 한국지능시스템학회논문지
• /
• 제22권6호
• /
• pp.735-740
• /
• 2012

본 연구에서는 주성분 분석법 및 선형 판별 분석법을 이용한 다항식 방사형 기저 함수 신경회로망 분류기의 설계 방법론을 소개한다. 주성분 분석법과 선형판별 분석법을 사용하여 주어진 데이터의 정보 손실을 최소화한 특징데이터를 생성하고 이를 다항식 방사형 기저함수 신경회로망의 입력데이터로 사용한다. 방사형 기저 함수 신경회로망의 은닉층은 FCM 클러스터링 알고리즘으로 구성되며 연결가중치는 1차 선형식을 사용하였다. 최적의 분류기 설계를 위해서 최근에 제안된 Artificial Bee Colony(ABC) 최적화 알고리즘을 사용하여 구조 및 파라미터를 동조하였다. ABC 알고리즘을 통해 주성분 분석법과 선형판별 분석법의 고유벡터의 수 및 FCM 클러스터링 알고리즘의 퍼지화 계수등의 파라미터를 동조한다. 제안된 분류기는 대표적인 Machine Learning(ML) 데이터를 사용하여 성능을 평가하며 기존 분류기와 성능을 비교한다.

• 마이크로전자및패키징학회지
• /
• 제24권2호
• /
• pp.37-41
• /
• 2017

$Cu_2O$는 초저가 태양전지의 흡수층으로 적용될 수 있는 물질 중 하나로 direct band gap($E_g={\sim}2.1eV$)을 갖고 있으며 최대 650 nm 파장의 빛을 흡수 할 수 있는 높은 흡수율을 가지고 있다. 또한 무독성, 풍부한 매장량으로 낮은 비용 등의 여러 장점을 가지며 간단하고 저렴한 방법으로 대량으로 제작이 가능하다. 본 연구에서 Au가 증착된 $SiO_2/Si$ 기판 위에 전착법을 통해 $Cu_2O$ 박막을 제작하였다. 우리는 용액의 pH와 작업전극에 인가되는 전위, 용액의 온도와 같은 공정조건을 바꾸어주었고 최종적으로 XRD와 SEM 사진 분석을 통해 박막의 특성을 확인하였다.