• Journal of the Korean Institute of Landscape Architecture
• /
• v.33 no.2 s.109
• /
• pp.60-70
• /
• 2005

This study was carried out to elucidate the vertical characteristics of soil properties at six planted sites of land reclaimed from the sea, in Gwangyang Bay, Jeollanam-do Province, Korea. Based on the types of planting site, the chemical properties of the vertical soil layers varied. The vertical variation was great in the planting sites $Z_1\;and\;Z_2$, but less varied in the mounded planting sites $Z_3,\;Z_5,\;and\;Z_6$. Major reasons for the vertical variation in soil chemical properties included differences in the accumulation of organic matter, soil disturbance by heavy construction equipment, and heterogeneity of soil properties between soil horizons. As soil depths increased, soil salts varied. The electrical conductivity (ECe) increased in the lower areas of planting sites $Z_1\;and\;Z_2$, and the disturbed, saline planting site $Z_3$, but decreased in the lower areas of $Z_3,\;Z_5,\;and\;Z_6$. These tendencies did not coincided with exchange cation concentrations $(Na^+,\;K^+,\;Mg^{++},\;Ca^{++})$. Both total carbon (T-C) and total nitrogen (T-N) accumulated more in the lower areas of planting sites than in the higher areas, and levels were higher closer to the surface than in the soil depths. It is supposed that these tendencies are related to the accumulation of fallen leaves or other organic matter at the soil surface, and the soil chemicals then slowly move downward from the surface. Impediments to tree growth included soil hardiness, high soil salinity and exchangeable cation concentration, low soil moisture content, acidic or alkaline soil, low organic matter, heterogeneity of soil texture and establishment of soil stratification.

• Journal of the Korean Ceramic Society
• /
• v.47 no.4
• /
• pp.329-332
• /
• 2010

In order to investigate the effect of tail state on the electrical and the optical properties in amorphous IGZO(a-IGZO), a-IGZO films were deposited at room temperature on fused silica substrats using pulsed laser deposition method. The laser pulse energy was used as the processing parameter. In-situ post annealing was carried out at $150^{\circ}C$ right after the film deposition. The $O_2$ partial pressure during the deposition and the post annealing was fixed to 10mTorr. The carrier mobility of the a-IGZO films had a range from 2 to $18\;cm^2/Vs$ at carrier concentrations greater than $10^{18}\;cm^{-3}$. As the laser energy density increased, the Hall mobility increased. And post annealing improved the Hall mobility, as well. The optical property was examined using the ultraviolet-visible spectroscopy. The a-IGZO films that have low Hall mobility exhibited stronger and broader absorption tails in >3.0 eV region. Post annealing reduced the intensity of the tail-like absorption. The absorption tail in a-IGZO films is an important factor which affects the electrical and the optical properties.

• Corrosion Science and Technology
• /
• v.6 no.4
• /
• pp.147-153
• /
• 2007

This study sought to investigate the reaction of Co-binder containing tungsten with molten zinc. Four kinds of Co-W alloys (pure, 10%W, 20%W, 30%W) were prepared using the powder metallurgy method. The specimens were immersion-tested in molten pure zinc baths at $460^{\circ}C$. To evaluate the corrosion property in molten zinc, the weight loss of the specimen was measured after the immersion tests at different immersion times (10~300 min.). Co-10%W alloys, compared with pure cobalt, showed no effect of tungsten addition on the reaction rate in molten zinc. The relationship between the weight loss and the square root of immersion period represents a straight line in both pure cobalt and Co-10%W alloy. The Co-Zn reaction layer in Co- 1O%W alloy consists of $\gamma2$, $\gamma1$, $\gamma$ and ($\beta1$ phases. The rate of weight loss significantly increases and the weight loss behavior is not well accord with the linear relationship as the tungsten content in the Co-W alloy increases. The $\beta1$ layer was not formed on the Co-20%W alloy and neither was a stable Co-Zn intermetallic compound layer found on the Co-30%W alloy. The main cause of increase in reaction rate with increasing tungsten content is related with the instability of the Co-Zn reaction phases as seen on micro-structural analysis.

• Nuclear Engineering and Technology
• /
• v.43 no.3
• /
• pp.279-286
• /
• 2011

The aging degradation and lifetime assessment of a domestic class 1E Ethylene-Propylene-Diene-Monomer (EPDM), which is a popular insulating elastomer for electrical cables in the nuclear power plants, were studied for equipment qualification verification under the Loss of Coolant Accident (LOCA) conditions. The specimens were acceleratively aged, underwent a LOCA environment, as well as tested mechanically, thermo-gravimetrically, and spectroscopically according to the American Society of the Testing of Materials (ASTM) procedures. The tensile test results revealed that the elongation at break gradually decreased with an increasing aging temperature. The lifetime of EPDM aged isothermally at $140^{\circ}C$ was 1,316 hours and reduced to 1,120 hours after experiencing the severe accident test. The activation energies of the elongation reduction were $1.10{\pm}0.196$ eV and $0.93{\pm}0.191$ eV before and after the LOCA condition, respectively. The TGA test results also showed that the activation energy of the aging decomposition decreased from 1.35 eV to 1.02 eV after undergoing the LOCA environment. Although the mechanical property changes were discernibly observed during the aging process, along with the LOCA simulation, the FT-IR analysis showed that the spectroscopic peaks and their intensities did not alter significantly. Therefore, it can be concluded that the degradation of the domestic class 1E EPDM due to aging can be tolerable, even in severe accident conditions such as LOCA, and thus it qualifies as a suitable insulating material for electrical cables in the nuclear power plants.

• Earthquakes and Structures
• /
• v.14 no.6
• /
• pp.615-626
• /
• 2018

The seismic vulnerability of Turkey is relatively high due to its active fault systems with potential to create destructive earthquakes. Thus, reducing the loss of life and property, the number of the earthquake-prone buildings and their retrofit requirements are considerably significant key issues under the scenario earthquakes. The street survey based rapid assessment (SSRA) method can be considered as a powerful tool to determine the seismic vulnerability of building stock of an earthquake-prone city/state. In this study, the seismic vulnerability of the building stock of the Kirikkale province in Turkey is aimed to be estimated adopting the street survey based rapid assessment method (SSRA). For this purpose, central 2074 existing reinforced concrete (R/C) buildings were structurally surveyed with rapid visual site screening and disadvantages such as, the existence of short-column, soft-story, heavy overhangs, pounding effect and local soil conditions were determined for obtaining the structural performance score of each. The results obtained from the study demonstrate that 11-25% of the surveyed buildings in the study region needs to be investigated through more advanced assessment methods. Besides, higher correlation between increasing story number and unsafe/safe building ratio is obtained for the buildings with soft-story parameter than that for those with heavy overhangs and short-column parameters. The conformity of the results of the current study with the previous documented cases of rapid assessment efforts in the recent earthquakes in Turkey shows that the SSRA method for the Kirikkale province performed well, and thus this methodology can be reliably used for similar settlement areas.

• Journal of Pharmaceutical Investigation
• /
• v.34 no.2
• /
• pp.91-94
• /
• 2004

To develop a poloxamer-based solid suppository with poloxamer mixtures, the melting points of various formulations composed of P 124 and P 188 were investigated. To investigate the effect of poloxamer to the dissolution ad dissolution mechanism of diclofenac sodium from the suppository the dissolution of diclofenac sodium delivered by the poloxamer-based suppository was performed. Furthermore, to investigate the mucoadhesive property of the poloxamer-based sold suppository, the identification test in the rectum was carried out after its rectal administration in rats. The poloxamer mixtures composed of P 124 and P 188 were homogeneous. Ver small amounts of P 188 affected the melting points of poloxamer mixtures. In particular, the poloxamer mixture [P 124/P 188 (97/3%)] with the melting point of about $32^{\circ}C$ was a sold for at room temperature and instantly melted at physiological temperature. Furthermore, very small amounts of P 188 in the poloxamer-based suppository hardly affected the dissolution rates of diclofenac sodium from the suppository. Dissolution mechanism analysis showed the dissolution of diclofenac sodium was proportional to the time. At 4 h after administration, the blue colo of poloxamer-based suppository [diclofenac sodium/poloxamer mixture (2.5/97.5%)] with the P 124/ P 188 ratio of (97/3%) and blue lake in the rectum was faded. However, the position of suppository in the rectum did not significantly change with time. Thus, it retained in thε rectum for at least 4 h. Our results indicated that the poloxamer-based sold suppository with P 124 and P 188 would be a candidate of rectal dosage form for diclofenac sodium.

• Textile Coloration and Finishing
• /
• v.25 no.1
• /
• pp.37-46
• /
• 2013

This paper surveys the ESD characteristics of the PANI added PU/MWNT film according to the manufacturing conditions such as variation of the loading contents of PANI and the mixture ratio of 2 dispersion solutions. For this purpose, PANI added PU/MWNT ground films were made with IPA/MWNT 3wt% dispersion solution and PANI/DMF dispersion solutions(5, 10, 15, 20, 25, and 30wt% contents of the PANI) by the mixture ratio of dispersion solution(10/50, 20/40, 30/30, 40/20, and 50/10part) in the PU (972DF) 100g, which was treated with 500rpm for 30min in the stirrer with condition of the dry temperature $120^{\circ}C$ for 2min. Totally, 36 kinds of PANI added PU/MWNT film specimens were prepared. The physical properties of the PANI added PU/MWNT films such as electrical resistivity, absorbancy by UV-Vis spectrometer, and triboelectricity were measured and discussed with surface characteristics of the PANI added PU/MWNT films by SEM. The dispersion property of PANI to the DMF showed best dispersion at the 25% of PANI content. The surface electrical resistivity of the PANI added PU/MWNT films was decreased with increasing the weight content of PANI/DMF dispersion solution, and it showed the lowest value $10^6{\Omega}$ at the mixing condition of PANI/DMF 20part and MWNT/IPA 40part with 30% PANI. Furthermore, it was shown that the electrical and physical properties of the PANI added PU/MWNT film such as electrical resistivity, and triboelectricity were better than those of PU/MWNT film prepared with no PANI, which was result obtained in previous paper.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.12
• /
• pp.3277-3285
• /
• 1996

In this paper, w designed an opical power distribution device for application to an optical switching and an optical subscriber loop. We fabricated PSG thin film by LPCVD. Based on the measured index of fabricted thin film, rib-type waveguide was transformed to two-dimension by the effective index method and we simulated dispersion property to find asingle-mode condition. We found that the optimum design parameters of rib-type waveguide are:cladding layer of 3.mu.m, core layer of 3.mu.m, buffer layer of 10.mu.m, and core width of 4.mu.m. Each side of the guiding region was etched down to 4.mu.m to shape the core. We used these optimum parameters of the rib-type waveguide with branching angle of 0.5.deg. and simulted the Y-branch waveguide by the BPM simulation. Numerical loss in branching area was claculated to be 0.1581dB and equal to the total loss of the Y-branch. The loss of the fabricated Y-branch waveguide on PSG film ws 1.6dB at .lambda.=1.3.mu.m before annealing but was 1.2dB after annealing at 1000.deg. C for 10 minutes. Consequently, the loss of branching area from 3000.mu.m to 6000.mu.m in the z-direction was 0.8dB, and single-mode propagation was confirmed by measuring the near field pattern. For coupling the fabricated Y-branch waveguide with an optical fiber, we fabricated V-groove which was used as the upholder of optical fiber. An etching angle was 54.deg. and the width and depth of guiding groove was 150.mu.m, 70.mu.m, respectively. The optical fiber is inserted onto V-groove. Both the Y-branch and V-groove were connected through the index matching oil. Coupling loss after connecting Y-branch and the optical fiber on V-groove was 0.34dB and that after injecting index mateching oil was 0.14dB.

• Journal of Powder Materials
• /
• v.21 no.3
• /
• pp.215-221
• /
• 2014

Translucent alumina is a potential candidate for high temperature application as a replacement of the glass or polymer. Recently, due to the increasing demand of high power light emitting diode (LED), there is a growing interest in the translucent alumina. Since the translucent property is very sensitive to the internal defect, such as voids inside or abnormal grain growth of sintered alumina, it is important to fabricate the defect-free product through the fabrication process. Powder injection molding (PIM) has been commonly applied for the fabrication of complex shaped products. Among the many parameters of PIM, the flowability of powder/binder mixture becomes more significant especially for the shape of the cavity with thin thickness. Two different positions of the gate were applied during PIM using the disc type of die. The binder was removed by solvent extraction method and the brown compact was sintered at $1750^{\circ}C$ for 3 hours in a vacuum. The flowability was also simulated using moldflow (MPI 6.0) with two different types of gate. The effect of the flowability of powder/binder mixture on the microstructure of the sintered specimen was studied with the analysis of the simulation result.

• Journal of Powder Materials
• /
• v.21 no.3
• /
• pp.207-214
• /
• 2014

In this study, nano-scale copper powders were reduction treated in a hydrogen atmosphere at the relatively high temperature of $350^{\circ}C$ in order to eliminate surface oxide layers, which are the main obstacles for fabricating a nano/ultrafine grained bulk parts from the nano-scale powders. The changes in composition and microstructure before and after the hydrogen reduction treatment were evaluated by analyzing X-ray diffraction (XRD) line profile patterns using the convolutional multiple whole profile (CMWP) procedure. In order to confirm the result from the XRD line profile analysis, transmitted electron microscope observations were performed on the specimen of the hydrogen reduction treated powders fabricated using a focused ion beam process. A quasi-statically compacted specimen from the nano-scale powders was produced and Vickers micro-hardness was measured to verify the potential of the powders as the basis for a bulk nano/ultrafine grained material. Although the bonding between particles and the growth in size of the particles occurred, crystallites retained their nano-scale size evaluated using the XRD results. The hardness results demonstrate the usefulness of the powders for a nano/ultrafine grained material, once a good consolidation of powders is achieved.