• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.05a
• /
• pp.128-131
• /
• 2000

This paper describes design for dual-linear polarization antenna using EMC(electromagnetic-coupled) dipole. EMC dipole has a simple element structure and it is fed by microstrip line. Vortical and horizontal polarization are determined by structure of dipole fed by microstrip line. FDTD Method is used for an analysis of antenna element. Length, width, height and offset of dipole are designed for 1-element antenna. Resonant length of diploe differs from the calculated value by a formula because of coupling effect of dipole and feed line. Radiation Power is controlled by the offset of dipole. In prectical fabrication of antenna array, a constant height of dipoles is required. Therefore, the teflon plate with height of 0.8 mm is considered in antenna element design for the vertical polarization.

• Journal of the Korean Society of Safety
• /
• v.19 no.2
• /
• pp.1-5
• /
• 2004

Al-brass is the raw material of mnufacturing tubes for heat exchanger of vessel where seawater is used to coolant because it has high level of heat coductivity and excellent mechanical properties and high level of corrosion resistance due to cuprous oxide($Cu_2O$) layer against seawater. However, damage of Al-brass tubes for heat exchanger of vessel is reported that local corrosion such as stress corrosion cracking occurred by synergism effect between mechanical factor and corrosion environment. In this study, to investigate on the effect of stress on the polarization characteristics of Al-brass. At the stress of 0% and 95% yield strength by constant displacement tester, in 3.5% NaCl + 0.1% $NH_4OH$ solution, the polarization tests were carried out. And thus open circuit potential, corrosion current density, anodic polarization, cyclic polarization and dezincification behavior of Al-brass are investigated.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2003.09a
• /
• pp.289-292
• /
• 2003

Laboratory tests were performed to investigate the dielectric property of saturated sands contaminated by heavy metals solution at low frequency. Differences of contamination and the real part of dielectric constant depend on heavy metal concentration was measured at low frequency, 100KHz below. The optimal frequency to develop the detection potentials of monitoring was 1KHz, 10KHz, 100KHz. At this frequency, Heavy metal contamination of saturated sands contamination can be recommended by analysis of complex dielectric constant.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.371-374
• /
• 2002

Bismuth lanthanum titanate thin films with excess Bi contents were prepared onto Pt/Ti/$SiO_2$/Si substrate by metalorganic decomposition (MOD) technique. The structure and morphology of the films were analyzed using X-ray diffraction (XRD) and atomic force microscopy (AFM), respectively. From the XRD analysis, BLT thin films show polycrystalline structure and the layered-perovskite phase was obtained over 10% excess of Bi contents. As a result of ferroelectric characteristics related to the Bi content of the BLT thin film, the remanent polarization and dielectric constant decreased with increasing over Bi content of 10 % excess. The BLT film with Bi content of 10% excess was measured to have a dielectric constant of n9 and dielectric loss of 1.85[%]. The BLT thin films showed little polarization fatigue test up to 3.5 x $10^{9}$ bipolar switching cycling.

• The Journal of Natural Sciences
• /
• v.17 no.1
• /
• pp.31-37
• /
• 2006

We have found that the polarization mode coupling between the orthogonally linearly polarized dual mode laser results from the anisotropy of dipole moments. Rate equation analysis demonstrated that high anisotropy in dipole moment components can give rise to law intrinsic mode coupling constants while isotropic dipole moment components give high intrinsic mode coupling constant. The populations at active ion sites are shown to self-organize the populations such that laser mode gain is constant adove threshold while the gain contributions from the each site adjust themselves with pump power.

• Journal of the Korean Ceramic Society
• /
• v.17 no.2
• /
• pp.75-79
• /
• 1980

The effect of the additive on the dielectric property of $TiO_2$ containing 0-2.5wt %. $Sb_2O_3$ was investigated as a function of frequency from $5{\times}10^4$ to $6.3{\times}10^7$ cps and temperature from 25 to 375$^{\circ}C$. The dielectric constant increased with increasing $Sb_2O_3$ concentration from 0.25 to 0.5wt.% It is due to space charge polarization caused by increasing anion vacanices. The dielectric constant decreased for further increase in $Sb_2O_3$ concentration. It can be explained by increasing grain size effect rather than space charge polarization.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.7
• /
• pp.30-35
• /
• 1995

Periodically slotted dielectrically filled paralled-plate waveguide as a leaky wave antenna is analysed for E-polarization case. The homogeneous linear equation whose unknown is the surface current density over the conducting strip is formulated, from which the complex propagation constant is calculated and compared with the previous results. Good correspondence between them is observed. And a method for the radiation pattern is also considered.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.113-117
• /
• 1999

SrBi$_2$Ta$_2$$O_{9}$ (SBT) thin films were fabricatcd with different Sr/Bi ratios by MOD. SBT thin films of thickness 2500$\AA$ deposited on Pt/Ti/SiO$_2$/Si were crystallized at $700^{\circ}C$ ~85$0^{\circ}C$ using RTA method. As the Sr/Bi ratio was decreased, dielectric constant and remanent polarization were increased. SrBi$_2$Ta$_2$$O_{9}$ showed a maximum dielectric constant value of $\varepsilon$$_{r}$= 268, and maximum remanent polarization (2Pr) of ~9.86 $\mu$C/$\textrm{cm}^2$ when annealed at 8$0^{\circ}C$ for 8 min.min.n.

• Electrical & Electronic Materials
• /
• v.10 no.3
• /
• pp.239-246
• /
• 1997

The ZnO is stabilize dielectric constant over a broad temperature range because its addition makes the relaxation time short. In this study, the composite oxide material (B $a_{0.85}$ $Ca_{0.15}$)Ti $O_{3}$ was mixed by ZnO additive material and the dielectric polarization characteristics was studied. The relative density was over 90[%] at all specimen in the structural characteristics. Among of the specimen, the relative density of (B $a_{0.85}$ $Ca_{0.15}$)Ti $O_{3}$ with ZnO (0.4mol) has a 95[%]. The grain size of composite oxide material with an increasing ZnO increased and it was 1.0[.mu.m]-1.22[.mu.m]. In the electrical characteristics, the charge and discharge current was increased by ZnO addition. The dielectric relaxation time was increased by space charge polarization at above 110[.deg. C] and the dielectric relaxation time was fixed by space charge polarization of para-dielectric layer at below 110[.deg. C]. The dielectric relaxation time was maximum when the grain size was small. The dielectric relaxation time is decreased with an additive material ZnO and interface polarization, existing void at the grain and grain boundary. The remnant polarization is increased and the coercive electric field is decreased by ZnO.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.5
• /
• pp.356-361
• /
• 2001

The structureal, dielectric and piezoelectric properties of Pb[(Sb$\_$1/2/Nb$\_$1/2/)$\_$x/-(Ni$\_$1/3/Nb$\_$2/3/)$\_$0.15-x/-(Zr$\_$y/Ti$\_$1-y/)$\_$0.85/]O$_3$(x=0∼0.05, y=0.47∼0.52) ceramics were investigated with the substitution of Pb(Sb$\_$1/2/Nb$\_$1/2/)O$_3$(abbreviated PSN) and the Zr/Ti ratio. At Zr/Ti ratio of 50/50, tetragonality was decreased and grain size abruptly decreased with the increase of PSN substitution. Curie temperature was decreased and dielectric constant increased with the substitution of PSN. The coercive field increased and remnant polarization decreased with the substitution of PSN. Electromechanical coupling factor(k$\_$p/) showed the highest value of 0.622 at 1mol% PSN, but mechanical quality factor(Q$\_$m/) showed the minimum value at that composition. Dielectric constant and electromechanical coupling factor with the Zr/Ti ratio showed maximum values at Zr/Ti ratio of 50/50 and mechanical quality factor showed minimum values near the Zr/Ti ratio of 50/50.