• 한국산업융합학회 논문집
• /
• 제25권4_2호
• /
• pp.611-619
• /
• 2022

In this study, the seismic performance of low - rise piloti buildings with concentric core (shear wall) position is analysed and reviewed based on KDS 41. The prototype is selected among the constructed low - rise piloti buildings with concentric core designed based on KBC 2005 which was used for many low - rise piloti buildings construction. The seismic performance of the building shows plastic behavior in X-direction and elastic behavior in Y-direction. The inter-story drift is lager than that of concentric core case and is under the maximum allowed drift ratio. The displacement ratio of first story is much lager the that of upper stories, and the frame structure in the first story is evaluated as vulnerable to lateral force. Therefore, low - rise piloti buildings with concentric core need the diminishment of lateral displacement and reinforcement of lateral resistance capacity in seismic design and seismic retrofit.

• 한국강구조학회 논문집
• /
• 제29권6호
• /
• pp.443-453
• /
• 2017

본 연구에서는 데크형 중공슬래브의 중공률을 확보하기 위한 방안으로 기존의 중공슬래브에 일반적으로 사용되는 구형형상의 경량체 대신 사다리꼴 형상의 경량체를 적용하고, 이에 따른 휨 및 전단 내력 성능을 실험을 통해 확인하였으며, 일방향 데크플레이트의 설치방향에 따른 구조특성을 검토하였다. 그 결과 휨내력 측면에서는 기존 구형형상의 경량체를 가진 중공슬래브와 동등한 수준의 성능을 발휘하는 것을 확인하였으며, 전단내력 측면에서는 경량체 형상 변화에 따른 차이보다는 데크플레이트의 트러스철선의 기여에 따라 큰 전단내력성능을 발휘하는 것을 확인하였다. 중공체 설치시 콘크리트 유효단면의 감소로, 전단 강도가 약 50~60% 정도로 저하된다는 기존 연구에 따른 계산한 전단내력값과 비교하였을 때, 폭방향으로 데크를 설치하여 트러스철근이 전단에 영향을 미치지 않을 것으로 가정한 실험체도 트러스철근의 트러스프레임 거동에 의한 영향으로 저감 전 값 대비 87%의 성능을 보여 기존 연구에 따른 계산전단내력보다 최대하중이 더 크게 나타났다.

• 콘크리트학회논문집
• /
• 제27권2호
• /
• pp.137-145
• /
• 2015

슬래브 형식 프리캐스트 모듈러교량은 횡방향으로 분절되어 제작된 프리캐스트 모듈을 현장에서 조립하는 형태의 교량으로서 분절된 프리캐스트 모듈 사이에는 종방향 연결부가 형성되며, 프리캐스트 모듈의 조립은 모듈 사이에 고성능 무수축 모르타르를 주입한 후에 횡방향으로 긴장력을 도입함으로써 이루어진다. 본 연구에서는 연결부의 휨 거동을 바탕으로 설계단계에서 산정된 횡방향 도입 긴장력 수준의 적정성 및 연결부의 형상이 휨 거동에 미치는 영향을 검토하기 위해 슬래브 형식 프리캐스트 모듈러교량의 연결부를 적용한 실험체를 이용한 4점 재하 휨 실험과 3점 재하 휨 실험을 수행하였다. 4점 재하 휨 실험은 긴장력의 변화가 연결부의 휨강도에 영향을 미치며 연결부의 형상은 순수한 휨모멘트가 작용하는 단면의 휨강도에는 영향을 미치지 않는다는 결과를 보여주었다. 3점 재하 휨 실험은 연결부에 휨모멘트와 전단력을 동시에 작용시키는 실험 방법으로, 연결부의 형상이 휨강도와 균열 사용성에 영향을 미친다는 결과를 보여주었다. 두 가지의 휨 실험 결과로부터 본 연구에서 적용한 긴장력은 적정하였으며 두 개의 전단키를 갖는 연결부가 균열 사용성 측면에서 유리하다는 것을 확인할 수 있었다.

• Restorative Dentistry and Endodontics
• /
• 제19권2호
• /
• pp.549-567
• /
• 1994

Restoration of severly damaged teeth after endodontic treatment had been an interest to many dentists, and it is a fact that there have been lots of studies about it. In these days, although we have used Para-Post, pins, threaded steel post, cast gold post and core, and so on, as a method of restoration frequently, it has been in controversy with the influence of them on the teeth and surrounding periodontal tissue. In this study, we assume that the crown of the upper incisor have severly damaged, so, after the root canal therapy, 4 types of restoration had been carried out; 1) coronal-radicular amalgam restoration, 2) after setting up the Para-Post, restore with composite resin core only, 3) after setting up the Para-Post; restore with amalgam core, then cover with the PPM crown 4) after setting up the Para-Post, restore with composite core, then cover with the PPM crown. After restoration, in order to observe the concentration of stress at internal portion of the teeth and the sourrounding periodontal tissue, developing a 2-dimensional finite element model of labiopalatal section, then loading forces from 3 direction - direction of 45 degrees from lingual side near the incisal edge, horizontal direction from labial height of contour, vertical direction at the incisal edge-were applied. The analyzed results were as follows: 1. Stress of the normal central incisor was concentrated on the dentin aroundpulp chamber, labiocervical portion of a tooth and root apex, but with the alveolar bone, in the case of load from the direction of 45 degrees from lingual side near the incisal edge showed remarkable concentration of stress: 2. Coronal-radicular amalgam technique -showed less concentration of stress on the root and surrounding periodontal tissue than the restoration with the Para-Post. 3. The von Mises equivalent stress on the Para-Post showed maximum value at root-core junction rather than both ends and model with PPM restoration with amalgam core showed the least concentration of stress. Only the force from horizontal direction showed large shear stress on internal portion of the root, root apex and alveolar bone. 4. PPM crown with composite core rarely showed the concentration of stress on root and periodontal tissue. 5. As for alveolar bone, remarkable shear stress was concentrated on labial and palatal side by horizontal load.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2009년도 춘계 학술대회 제21권1호
• /
• pp.27-28
• /
• 2009

건축물의 지진모의실험을 수행할 경우, 부재에 작용하는 전단력과 축력의 계측이 필요하다. 본 연구에서는 2축 전단, 1축 압축을 측정할 수 있는 Load Cell의 제작 및 Calibration법을 제시하고 있다.

• Steel and Composite Structures
• /
• 제34권2호
• /
• pp.241-260
• /
• 2020

This article presented a comprehensive model to study static buckling stability and associated mode-shapes of higher shear deformation theories of sandwich laminated composite beam under the compression of varying axial load function. Four higher order shear deformation beam theories are considered in formulation and analysis. So, the model can consider the influence of both thick and thin beams without needing to shear correction factor. The compression force can be described through axial direction by uniform constant, linear and parabolic distribution functions. The Hamilton's principle is exploited to derive equilibrium governing equations of unified sandwich laminated beams. The governing equilibrium differential equations are transformed to algebraic system of equations by using numerical differential quadrature method (DQM). The system of equations is solved as an eigenvalue problem to get critical buckling loads and their corresponding mode-shapes. The stability of DQM in determining of buckling loads of sandwich structure is performed. The validation studies are achieved and the obtained results are matched with those. Parametric studies are presented to figure out effects of in-plane load type, sandwich thickness, fiber orientation and boundary conditions on buckling loads and mode-shapes. The present model is important in designing process of aircraft, naval structural components, and naval structural when non-uniform in-plane compressive loading is dominated.

• Advances in Computational Design
• /
• 제7권3호
• /
• pp.229-251
• /
• 2022

In 2017, an intraplate earthquake of Mw 7.1 occurred 120 km from Mexico City (CDMX). Most collapsed structural buildings stroked by the earthquake were flat slab systems joined to reinforced concrete (RC) columns, unreinforced masonry, confined masonry, and dual systems. This article presents the simulated response of an actual six-story RC frame building with masonry infill walls that did not collapse during the 2017 earthquake. It has a structural system similar to that of many of the collapsed buildings and is located in a high seismic amplification zone. Five 3D numerical models were used in the study to model the seismic response of the building. The building dynamic properties were identified using an ambient vibration test (AVT), enabling validation of the building's finite element models. Several assumptions were made to calibrate the numerical model to the properties identified from the AVT, such as the presence of adjacent buildings, variations in masonry properties, soil-foundation-structure interaction, and the contribution of non-structural elements. The results showed that the infill masonry wall would act as a compression strut and crack along the transverse direction because the shear stresses in the original model (0.85 MPa) exceeded the shear strength (0.38 MPa). In compression, the strut presents lower stresses (3.42 MPa) well below its capacity (6.8 MPa). Although the non-structural elements were not considered to be part of the lateral resistant system, the results showed that these elements could contribute by resisting part of the base shear force, reaching a force of 82 kN.

• Design & Manufacturing
• /
• 제11권3호
• /
• pp.46-50
• /
• 2017

Press processing is one of the best machining methods capable of mass production, satisfying dimensional, shape and quality among the methods of processing a metal plate. Among them, Fine blanking is a method of obtaining a precise cross-section such as machining of the shear surface shape. In this research, Using SCP-1 and SHP-1 materials. The deformation behaviors of the material flow affecting the die height of the shear section in accordance with the position of the V-ring in the Fine blanking were compared and analyzed. Result of interpretation, It was confirmed that the force acts on the position where the material flow direction accurately forms the die roll that the material of SCP-1 is at a position of 1.5 mm and the material of SHP-1 is at 2.0 mm. As a result, it was confirmed that the state of fo1111ing the shear surface by the V-ring was excellent. Using analysis results, In the experiment, the height of the die roll was considered by applying The position of the V-ring was 1.5 mm in SCP-1 and 2.0 mm in SHP-1. As a result of comparing the height of the die rolls, the height values of the die rolls were different from each other, It has been considered that the tendency of the die rolls to coincide with each other. It is considered that the difference of the die roll height is caused by the pressure input of the V-ring. In this study, the deformation behavior of the material(In addition to the position of the V-ring, the flow direction of the material depends on the shape of the V-ring and the Indentation amount) is considered to be an important factor in determining die roll height.

• 한국터널지하공간학회 논문집
• /
• 제14권5호
• /
• pp.529-545
• /
• 2012

본 연구에서는 3차원 유한요소해석을 실시하여 견고한 점토에 기시공되어 있는 단독말뚝의 하부에서 실시된 open face 터널굴착에 의한 말뚝의 거동을 분석하였다. 수치해석에서는 터널굴착으로 인한 말뚝의 거동을 규명하기 위하여 지반, 말뚝의 침하 및 전단응력전이 메커니즘을 심도 있게 분석하였다. 터널굴착으로 인해 Greenfield 조건의 지표면의 침하를 크게 초과하는 말뚝침하가 발생하였으며, 말뚝과 인접지반 사이 경계면에서의 전단응력전이현상으로 인해 말뚝에 작용하는 축력의 분포가 매우 크게 변화하였다. 말뚝침하의 증가로 인하여 말뚝의 겉보기지지력(apparent pile capacity)이 약 30% 감소하는 것으로 분석되었다. 터널굴착에 따른 지중응력 및 변형에 의해 말뚝의 마찰력이 증가하는 현상이 발생하고 이에 따라 말뚝의 축력이 터널의 굴착에 따라 지속적으로 감소하였다. 순수하게 터널굴착에 의하여 단독말뚝에는 설계하중의 최대 21%에 상응하는 인장력이 유발되는 것으로 분석되었다. 말뚝은 터널의 시공이 말뚝의 중심에서 종방향으로 ${\pm}1$-2D (D: 터널직경)에서 실시될 때 가장 큰 영향을 받는 것으로 나타났다. 말뚝선단 인근에서는 (-)의 과잉간극수압이 발생하였으며, 말뚝상부 부근에서는 (+)의 과잉간극수압이 발현하였다. 터널굴착에 의한 말뚝의 사용성은 축력변화에 비해서는 말뚝의 침하에 의해 큰 영향을 받는 것으로 분석되었다.

• 한국공간구조학회논문집
• /
• 제23권1호
• /
• pp.45-52
• /
• 2023

This study proposes an RCS composite damping device that can achieve seismic reinforcement of existing buildings by dissipating energy by inelastic deformation. A series of experiments assessing the performances of the rubber core pad, hysteretic steel slit damping device, and hybrid RCS damping device were conducted. The results showed that the ratios of the deviations to the mean values satisfied the domestic damping-device conformity condition for the load at maximum device displacement in each direction, at the maximum force and minimum force at zero displacement, as well as the hysteresis curve area. In addition, three analysis models based on load-displacement characteristics were proposed for application to seismic reinforcement design. In addition, the validity of the three proposed models was confirmed, as they simulated the experimental results well. Meanwhile, as the shear deformation of the rubber-core pad increased, the hysteretic behavior of super-elasticity greatly increased the horizontal force of the damping device. Therefore, limiting the allowable displacement during design is deemed to be necessary.