• Journal of the Korean Ceramic Society
• /
• v.45 no.1
• /
• pp.54-59
• /
• 2008

Hydrated sodium silicate with 25 wt% water contents was synthesized by hydrothermal reaction using anhydrous sodium silicate. The hydrated sodium silicate was expanded at $370^{\circ}C$ for 30 min. and then pulverized, classified (- 200 mesh) and press-formed. The samples were heat treated at $400{\sim}900^{\circ}C$ for 30 min. in order to study the expansion characteristics depending on heat treatment temperature. A porous body with closed pore was formed above $600^{\circ}C$. The volume expansion ratio and the pore size were increased and the specific gravity was decreased with increasing heat treatment temperature. However, the volume expansion ratio was decreased and the specific gravity was increased above $850^{\circ}C$ due to the softening of the sodium silicate.

• Journal of Korean Society on Water Environment
• /
• v.26 no.2
• /
• pp.343-348
• /
• 2010

The objective of this study was to investigate the effects of starvation periods with aerobic or non-aerobic conditions on the organic removal efficiencies and physical characteristics of activated sludge for treating saline and non-saline wastewater. During the experiment, MLSS, MLVSS, sludge volume index (SVI), floc size and fractal dimension, $COD_{Mn}$ removal efficiencies were monitored. The reductions of MLSS, MLVSS and SVI with maintaining the sludge under a non-aerobic condition during starvation periods were smaller than those under a aerobic condition. Floc size, fractal dimension and $COD_{Mn}$ removal efficiencies were less decreased under non-aerobic condition than under aerobic condition. And SVI were strongly correlated with floc size and fractal dimension. Consequently, the result showed that maintaining the activated sludge under non-aerobic starvation conditions was better strategy than that under aerobic starvation conditions as it adapted and resisted to starvation.

• Journal of the Korean Ceramic Society
• /
• v.30 no.5
• /
• pp.411-419
• /
• 1993

A process for the preparation of cobalt oxide powders was developed by the evaporaton of emulsion containing cobalt. The characteristics of powders were examined by means of DTA, X-ray diffracton, SEM, PSA. Cobalt oxide powders were produced by evaporating the emulsion prepared by mixing cobalt sulfate solution and organic phase consisted of kerosene, Span 80 and D2EHPA in the kerosene bath at 16$0^{\circ}C$, then the precursor obtained was calcined at 100$0^{\circ}C$. As the concentration of cobalt ions in the aqueous solution, Span 80 and the stirring speed increased, the mean size of cobalt oxide powders decreased and the size distribution was improved. At the volume ratio of one of the aqueous to organic phase, the finest mean size and the optimum size distribution was obtained. On the other hand the concentration of D2EHPA and liquid paraffin had little effect on the mean size as well as on the size distribution of powders.

• Journal of Magnetics
• /
• v.20 no.1
• /
• pp.21-25
• /
• 2015

Fine Nd-Fe-B-type particles were prepared by ball milling of different types of Nd-Fe-B precursor materials, such as die-upset magnet, HDDR-treated material, and sintered magnets. Coercivity dependence on the grain and particle size of the powder was investigated. Coercivity of the milled particles was reduced as the particle size decreased, and the extent of coercivity loss was dependent upon the precursor material. Coercivity loss in the finely milled particles was attributed to the surface oxidation. The extent of coercivity loss in the fine particles was closely linked to grain size of the precursor materials. Coercivity loss was more profound for the fine particles with larger grain size. Contrary to the fine particles from the sintered magnets with larger grain size the fine particles (~10 um) from the die-upset magnet and HDDR-treated material with much finer grain size still retained high coercivity (> 10 kOe for die-upset magnet, > 4 kOe for HDDR-treated material).

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.5
• /
• pp.78-85
• /
• 2007

Recently, diesel vehicles have been increased and their emission standards have been getting strict. The emission of diesel vehicles contains numerous dangerous compounds, especially particulate matters cause a serious environmental pollutant and affect to human health seriously. Thousands of studies have already reported that particulate matters are associated with respiratory and cardiovascular diseases, and death. Due to these, it is necessary to measure the soot concentration and soot particle size in laboratory flames or practical engines to recognize the soot formation, and develop the control strategies for soot emission. In this study, the characteristics of exhausted soot particle size and volume fraction from 2.0L CRDI diesel engine have been investigated as varying engine speed and load. Laser induced incandescence has been used to measure soot concentration. Time-resolved laser induced incandescence has been used to determine soot particle size in the engine. The soot volume fraction is increased as increasing engine load but soot volume fraction is decreased as increasing engine speed. The primary particle size is distributed about $35nm{\sim}60nm$ at each experimental conditions.

• Korean Journal of Community Nutrition
• /
• v.12 no.5
• /
• pp.639-645
• /
• 2007

Using the diet rice bowl, this study examined whether visual cues related to portion size can influence intake volume without altering satiation. 24 subjects ate lunch and subsequent dinner meal in the lab once a week for 2 weeks. Each week at noon, they were served one of two different sizes of a rice (150 g of rice by the diet rice bowl and 210 g of rice by the general rice bowl) but recognized the same volume of which they could eat as much as they wanted of side dishes. Subjects returned to the lab five hours later for a standard dinner, which was consumed ad libitum. Results showed that the subjects who were eating from the diet rice bowl ate less rice (222.4 Kcal vs 306.5 Kcal, p < 0.001) and total energy intake (412.5 Kcal vs 499.2 Kcal, p < 0.001) than those eating from a general rice bowl at lunch. However, despite consuming 21% less energy intake at lunch, the rates of satiety were not significantly different after eating from the diet rice bowl and from the general diet bowl. And there were no significant difference in rice intake and energy intake at dinner between the diet rice bowl and the general rice bowl. These results suggest decreasing the portion size by the diet rice bowl with biased visual cues leads to decreased rice intake and energy intake without altering the satiation. This is, the decreased amount of rice in a diet rice bowl may implicitly suggest what might be construed as an appropriate amount to consume and eventually it suggests smaller consumption norms.

• Journal of the Korean Society for Heat Treatment
• /
• v.13 no.4
• /
• pp.265-271
• /
• 2000

The microstructural change and transformation characteristics with cooling rate i.e. wheel speed were investigated in 82.8wt%Cu-12.8wt%Al-4.3wt%Ni SMA ribbons fabricated by melt-spinning. The thickness and width of ribbon were decreased with increasing wheel speed, while the uniformity of it was improved. At same wheel speed, the grain size of the contact surface of ribbon was smaller than that of free surface. The mean grain size was decreased with increasing wheel speed, resulted in obtaining grains with $3{\mu}m$ in mean diameter in the wheel speed of 30 m/s. However, micro-voids and cracks at grain boundary could be observed at higher wheel speed. $M_s$ and $A_s$ temperatures were decreased, and $M_s{\sim}M_f$ and $A_s{\sim}A_f$ temperature ranges were broadened with increasing wheel speed. All the ribbons were retained the ordered $D0_3$ due to rapid cooling, the volume fraction of it was increased with increasing wheel speed.

• Journal of the Korean Magnetics Society
• /
• v.11 no.4
• /
• pp.157-162
• /
• 2001

Rheological characteristics of Sm-Co type plastic magnet compound for powder injection molding process were investigated with the variation of the magnetic powder size, their relative contents and volume fraction using the mixture of fine and coarse powder. Shear viscosity of Sm-Co type compound was decreased with increasing the size of coarse powder due to the increase of powder packing density. However, the smaller the average size of fine powder resulted in the higher viscosity of compound due to the increase of agglomeration force. In case of mechanically milled Sm-Co type powder, the viscosity of compound with the mixture of coarse powder of 125∼75 ㎛ and fine powder of average size of 4.9 ㎛ greatly depends on their relative contents and shows a minimum value at the 60 % coarse powder fraction. This means that the compound shows a maximum packing density at the 60% coarse powder fraction. Compound viscosities satisfied well the rheological model with the volume fraction of magnetic powder, and maximum volume fraction of magnetic powder in Sm-Co type compound for powder injection molding was about 66%.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.532-537
• /
• 2000

The purpose of this study is to determine the performance of a commercial air cleaner in removing tobacco smoke indoors. Following injection of tobacco smoke in a room, decay rates for particle concentrations were obtained far mass concentration at each point. The size distribution of the tobacco smoke particles was approximately $1.266{\mu}m$ in mass median diameter with a geometric standard deviation of 1.313. The air cleaner consisted of an electrostatic filtration unit and a fan operated at a flow rate of 5.98 CMM. The collection efficiency for $>1\;{\mu}m$ was more than 99%. Without air cleaner operation, tobacco smoke concentration ratio in room decreased to 30% of initial values within 30 minutes and with air cleaner operation, decreased to 90% of initial values in the test chamber, volume $51.27\;m^3$. Without air cleaner operation, tobacco smoke concentration ratio in room decreased to 10% of initial values within 30 minutes and with air cleaner operation, decreased to 30-70% of initial values in the test chamber, volume $149.2\;m^3$.

• Journal of Korea Foundry Society
• /
• v.14 no.5
• /
• pp.438-446
• /
• 1994

The effect of various thermomechanical treatments on the structure and rheological behaviour of Al-6.2wt%Si alloy in its solidification range were investigated using a Searle type high temperature viscometer. During continuous cooling, the viscosity increases gradually with increasing fraction of solidified alloy, until a critical fraction of solidified alloy is reached above which the viscosity sharply increases. The viscosity of the slurry, at a given volume fraction wolid, decreased with increasing shear rate. The size and morphology of primary solid particles during stirring is influenced strongly by shear rates, cooling rates, volume fraction and stirring time of solid. Morphological changes during stirring as a function of solid volume fractions, shear rate and processing time were also reported. In this study, the size of primary solid particles in these alloys consistently increases and the it`s aspect ratio decrease with the increase in fraction solid and decrease in shear rate. Crystal morphology changes from rosette type to spheroid type with the increase in shear rate and solid fraction.