• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.136-137
• /
• 2008

Solar cell's efficiency depends on silicon's characteristic itself, or additional process such as texturing, coating, etc. Using PC1D, by adjusting Texturing, Base Resistivity, Emitter Doping, simulate many situation and observe the result. When texture Angle=$80^{\circ}$, Texture Depth=2um, Base Resistivity = 0.2, Emitter Doping = 8*Exp(19) are set, the solar cell's efficiency si 19.89%, and optimized.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2008.06a
• /
• pp.387-390
• /
• 2008

소음지도는 공간의 소음값을 3차원적으로 분석하여 GIS 데이터에 소음분석결과값을 RGB 값으로 표현한 것이다. 현재의 GIS는 2차원 데이터이므로 3차원 소음분석결과값을 표현하고 사용자들에게 제공하는 것에 효과적이지 못하다. 따라서 본 연구에서는 소음분석결과값을 보다 효과적으로 사용자들에게 제공하기 위하여 3차원 소음지도를 제작하고자 한다. 3차원 소음지도는 도시공간모델의 지형과 건물을 각각 소음분석결과값을 이용하여 texturing하여 가시화한 후 통합하여 완성한다. 지형의 경우, 지형의 기하학적 가시화완 지형의 texturing의 두 단계를 거쳐 완성하고 건물의 경우, 건물의 기하학적 3차원 가시화와 건물의 texturing의 두 단계를 거쳐 생성한다. 건물과 지형의 texturing의 단계에서 texture file은 소음분석결과값을 RGB코드로 변환하여 jpg파일로 생성한다. 생성된 3차원 소음지도는 영등포구 전체 영역을 대상지로 하였고 web기반의 VRML파일이다. 가시화의 효율성을 고려하여 영등포구 영역을 $200m{\times}200m$로 구역을 설정 607개의 구역으로 나누어 가시화하였다. 도시공간 모델을 이용하여 3차원 소음지도를 제작함으로써 도시공간모델을 이용하는 응용분야에서 3차원 공간분석의 가시화를 위한 방법을 제시할 수 있었다. 이를 통하여 공간 문제들의 결과를 사용자들에게 보다 효율적으로 제공할 수 있을 것이다.

• Fashion & Textile Research Journal
• /
• v.1 no.2
• /
• pp.166-172
• /
• 1999

An experimental investigation has done for studying the changes of physical properties of the air-jet textured polyester yarn. Through the experiments of polyester 85/72 drawn yarn and 50/36 partially oriented yarn doubling' the following results are obtained. The tenacity of textured yarn decreased as the number of tension rings increased when the nozzle diameter was 1.2 mm. In the case when the tension ring was not used during the texturing process, the tenacity of textured yarn decreased as the nozzle diameter increased. But this tendency changed according to the number of tension rings used, the diameter of the nozzle, and yarn take-up speed. Breaking elongation decreased as the number of tension rings increased from one to four and the take-up speed increased at diameter 1.2 mm of the nozzle. The higher the diameter of the the nozzle the higher the breaking elongation until 1.4 mm. The number of interlacing went down as the diameter of the nozzle increased and the take-up speed of the yarn increased. The higher the number of tension rings, the lower the number of interlacing.

• International Journal of Advanced Culture Technology
• /
• v.11 no.4
• /
• pp.333-339
• /
• 2023

In three-dimensional(3D) modeling, texturing plays a crucial role as a visual element, imparting detail and realism to models. In contrast to traditional texturing methods, the current trend involves utilizing AI tools such as Leonardo.Ai and Meshy to create textures for 3D models in a more efficient and precise manner. This paper focuses on 3D texturing, conducting a comprehensive comparative study of AI tools, specifically Leonardo.Ai and Meshy. By delving into the performance, functional differences, and respective application scopes of these two tools in the generation of 3D textures, we highlight potential applications and development trends within the realm of 3D texturing. The efficient use of AI tools in texture creation also has the potential to drive innovation and enhancement in the field of 3D modeling. In conclusion, this research aims to provide a comprehensive perspective for researchers, practitioners, and enthusiasts in related fields, fostering further innovation and development in this domain.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.2
• /
• pp.121-125
• /
• 2011

Ribbon silicon solar cells have been investigated because they can be produced with a lower material cost. However, it is very difficult to get good texturing with a conventional acid solution. To achieve high efficiency should be minimized for the reflectance properties. In this paper, acid vapor texturing and anti-reflection coating of $SiN_x$ was applied for EFG Ribbon Si Wafer. P-type ribbon silicon wafer had a thickness of 200 ${\mu}m$ and a resistivity of 3 $\Omega-cm$. Ribbon silicon wafers were exposed in an acid vapor. Acid vapor texturing was made by reaction between the silicon and the mixed solution of HF : $HNO_3$. After acid vapor texturing process, nanostructure of less than size of 1 ${\mu}m$ was formed and surface reflectance of 6.44% was achieved. Reflectance was decreased to 2.37% with anti-reflection coating of $SiN_x$.

• Science of Emotion and Sensibility
• /
• v.17 no.3
• /
• pp.75-82
• /
• 2014

This study investigated the physical properties of aramid/nylon ATY and aramid ATY for protective garments according to the aramid and nylon characteristics fed on the core and effect components of air jet texturing equipment. Tenacity decrease of aramid ATY was much more higher than that of nylon ATY because of slick of aramid filament surface. Tenacity of aramid/nylon ATY was most affected by the tenacity of nylon on the effect component of ATY. Breaking strain of nylon ATY was two times higher than that of nylon before air jet texturing, then, in case of aramid ATY and aramid/nylon ATY, were 5.9-6.7 times higher than those before air jet texturing. Initial modulus decrease of aramid ATY showed 86.5% of initial modulus of aramid before air jet texturing, then aramid/nylon hibrid ATY showed arithmetic average value of initial modulus of aramid and nylon ATY. Wet and dry thermal shrinkages of aramid/nylon hybrid ATY were dominated by those of nylon filament on the effect component of ATY.

• Tribology and Lubricants
• /
• v.38 no.5
• /
• pp.191-198
• /
• 2022

With the world's fast expanding energy usage comes a slew of new issues. Because one-third of energy is lost in overcoming friction, tremendous effort is being directed into minimizing friction. Surface texturing is the latest surface treatment technology that uses grooves and dimples on the friction surface of the machine to significantly reduce friction and improve wear resistance. Despite the fact that many studies on this issue have been conducted, most of them focused on parallel surfaces, with relatively few cases of converging films, as in most sliding bearings. This study investigated the lubrication performance of surface-textured inclined slider bearings. We analyzed the continuity and Navier-Stokes equations using a commercial computational fluid dynamics code, FLUENT. The results show the pressure and velocity distributions and the lubrication performance according to the number and orientation of rectangular dimples. Partial texturing somewhat improves the lubrication performance of inclined slider bearings. The number of dimples with the maximum load-carrying capacity (LCC) and minimum friction is determined. When the major axis of the dimple is arranged in the sliding direction, the LCC and friction reduction are maximized. However, full texturing significantly reduces the LCC of the slider bearing and increases the flow rate. The results have the potential to improve the lubrication performance of various sliding bearings, but further research is required.

• Tribology and Lubricants
• /
• v.20 no.5
• /
• pp.266-271
• /
• 2004

The aim of this paper is to investigate the effect of surface texturing on reduction friction and to understand the potential of friction reduction through micro-scale dimple to fabricate by photolithography on pin-on-disk test using flat-on-flat contact geometry. It was verify that the friction property with respect to the same pitch has been influence on the size of dimple under lubricated sliding contact. Also, we can recognize from Stribeck curve that the friction property has a connection with the size of dimple. It can explain a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. The friction property has been an effect on the size of surface texture on reduction friction, not only because the density of dimple, but also because the ratio of diameter/pitch. This ratio of approximately 0.5 recommend under the tested friction condition. It suggested that the ratio of d/p is an important parameter for surface texture design.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.10a
• /
• pp.39-40
• /
• 2003

This research surveys the effects of POY physical properties and processing conditions of belt texturing machine to the draw textured yarns. The various textured yarns are made with variation of 1st heater temperature, draw ratio and velocity ratio, and the physical properties of these specimens such as yarn linear density, tensile properties and wet and dry thermal shrinkages are measured and analyzed with POY physical properties and processing conditions of texturing machine. Especially yarn mechanical properties of DTY are analysed with the variation of untwisting tension (T$_2$) on the untwisting part in DTY process and thin and thick DTY yam model are proposed with surging phenomena in DTY process.

• Textile Coloration and Finishing
• /
• v.20 no.2
• /
• pp.47-52
• /
• 2008

Nylon textured yarn is usually manufactured by disk type false twist texturing. Dyeing properties of nylon textured yam have not been studied yet. In this study, dyeing properties of nylon textured yam according to draw ratio out of process parameters were investigated. The fact that microstructure of nylon textured yarn in amorphous region particularly is transformed by draw ratio was confirmed indirectly by measurement of dyeing rate because dyeing rate was affected by the structure of amorphous region. Dyeing rate at draw ratio 1.29 was the lowest because the higher draw ratio increase amorphous orientation and disturb dye diffusion into amorphous region. The microstructure according draw ratio was indirectly confirmed by 5% strength, tenacity, elongation. But difference in K/S value and fastness was insignificant.