• 대한전기학회논문지:전력기술부문A
• /
• 제54권6호
• /
• pp.284-292
• /
• 2005

Because all of the short-circuit testing laboratories have the limitation of test facilities, the synthetic making test methods have been used to estimate the short-circuit making performance of the ultra high-voltage circuit breaker as the alternative to direct test methods. So, KERI(Korea Eelctrotechnology Research institute) has completed the construction of the synthetic making test facilities using the low capacity step-up transformer method which fulfill the requirements specified in newly revised IEC 62271-100 Edition 1.1(2003) and have the testing capability up to 550kV, 63kA full-pole circuit breaker. The test facilities using the low capacity step-up transformer method presented in this paper are made up of the unit equipments such as HCS(High-speed Closing Switch), ITMC(Initial Transient Making Current) circuit and UP TR(low capacity step-up transformer) and have the operating range of 17.6$^{\circ}$ $\~$ 145.1$^{\circ}$ for testing the circuit breaker rated on up to 50kA and 43.1$^{\circ}$ $\~$ 119.6$^{\circ}$ for more than 50kA.

• 비파괴검사학회지
• /
• 제20권6호
• /
• pp.562-567
• /
• 2000

발전 및 산업설비에 사용되는 많은 압력용기는 저합금강을 사용하여 제작되고 있다. 압력용기의 내면은 부식이 미치는 영향을 최소화하기 위하여 오스테나이트계 스테인리스강으로 덧살용접을 하고 있으나, 용접층간의 계면에서 발생하고 있는 박리균열은 압력용기의 신뢰성에 중요한 변수가 되고 있다. 본 연구에서는 DSP를 사용하여 오버레이 용접부를 고속으로 검사할 수 있는 C-scan 시스템을 개발하였다. 본 시스템은 신호 처리부 (오실로스코프, 펄서/리시버, 디지타이저, DSP), 스캐너, 프로그램 및 위치 제어부로 구성되어 있다. 개발된 시스템을 사용하여 실제 오버레이 용접부에 대한 초음파검사를 실시한 결과 고속으로 신뢰성 높은 검사결과를 얻을 수 있었다.

• 한국철도학회논문집
• /
• 제10권6호
• /
• pp.800-805
• /
• 2007

철도차량용 대차의 한계 성능에 대한 검증은 설계 검증 및 안전성 확보관점에서 매우 중요하다. 차량의 안정성과 관련된 대차의 임계속도는 차량 개발 단계에서 총상 주행시험대를 이용하여 시험을 수행한다. 그러나 실물 대차를 이용한 시험과정에서 다양한 시제차량 제작 및 시험 조건 설정의 어려움, 시험 소요시간의 과다 등에 의한 단점을 내포한다. 따라서 철도 선진국등에선 과거 오래전부터 축소모델을 이용한 차량 개발 연구가 활발하였다. 따라서 본 연구에서는 대차의 임계속도 및 동적 거동 분석을 위하여 상사기법을 적용한 축소대차를 제작하였고 이를 시험하기 위한 축소 주행 시험대를 개발하였다. 축소대차 임계속도에 대한 수치해석을 수행하였으면 주행시험대상에서의 임계속도 시험을 통하여 해석결과가 시험결과에 부합함을 확인할 수 있었다.

• 한국태양에너지학회 논문집
• /
• 제26권4호
• /
• pp.63-71
• /
• 2006

The installed capacity of wind turbines in KOREA are growing and enlarging by the central government's support program. Thus, the importance of power performance verification and its uncertainty analysis are recognizing rapidly. This paper described the Power testing results of a 1.5MW wind turbine and analysed an uncertainty level of measurements. The measured power curves are very closely coincide with the calculated one and the annual power production under the given Rayleigh wind speed distribution are estimated with the $4.7{\sim}22.0%$ of uncertainty but, in the dominant wind speed region as $7{\sim}8m/s$, the uncertainty are stably decreased to $7{\sim}8%$.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제10권6호
• /
• pp.2583-2605
• /
• 2016

Fingerprint positioning is a main stream and key technique for seamless positioning systems. In this paper, we develop a performance evaluation testbed for fingerprint based Wireless Local Area Network (WLAN) positioning system. The testbed consists of positioning server, positioning terminal, Access Point (AP) units, positioning accuracy analysis system and testing scenarios. Different from other testbeds tended to focus on testing in same situation, in the proposed testbed, a couple of scenarios are set to test the positioning system including indoor and outdoor environments. Handset-side positioning mode and network-side positioning mode are provided simultaneously. Variety of motion models, such as static model, low-speed model and high-speed model are considered as well as different positioning algorithms. Finally, some implementation cases are analyzed to verify the credibility of the testbed.

• 비파괴검사학회지
• /
• 제23권6호
• /
• pp.583-593
• /
• 2003

The effect of liquid confined in a pipe on elastic waves propagating in the pipe wall was studied theoretically and experimentally. The axisymmetric motion of the wave was modeled with the cylindrical membrane shell theory. The liquid pressure satisfying the axisymmetric wave equation was included in the governing equation as a radial load. The phase speed of the wave propagating in the axial direction was calculated, accounting for the apparent mass of the liquid. Experiments were performed in a pipe equipped with ring-shaped, piezoelectric transducers that were used for transmitting and receiving axisymmetric elastic waves in the pipe wall. The measured wave speeds were compared with the analytical ones. This work demonstrates the feasibility of using pipe waves for the determination of the density and, eventually, the flow rate of the liquid in a pipe.

• 비파괴검사학회지
• /
• 제32권6호
• /
• pp.696-702
• /
• 2012

In this study, a noncontact laser ultrasonic system is proposed for rail defect detection. An Nd-Yag pulse laser is used for generation of ultrasonic waves, and the corresponding ultrasonic responses are measured by a laser Doppler vibrometer. For the detection of rail surface damages, the shape of the excitation laser beam is transformed into a line. On the other hand, a point source laser beam is used for the inspection of defects inside a rail head. Then, the interactions of propagating ultrasonic waves with defects are examined using actual rail specimens. Amplitude attenuation was mainly observed for a surface crack, and reflections were most noticeable from an internal damage. Finally, opportunities and challenges associated with real-time rail inspection from a high-speed train are discussed.

• Tribology and Lubricants
• /
• 제13권1호
• /
• pp.76-81
• /
• 1997

The lubrication characteristics of high-speed roller bearings at oil-starvation have been investigated empirically using the bearings employed in small industrial gas turbine engines. Testing was done by simulating the oil-starvation conditions in engines, such as stopping the oil-supply to the bearing during normal operating, starting without oil-supply at atmospheric temperature, and accelerating with oil-supply at atmospheric temperature. During testing, the temperature of bearing, the power consumption, and the rotating resistance of the bearing were measured. From this study, on the contrary to the ball bearing, it was found that the resistance of the bearing was higher at the regime of without oil-supply than that at the regime of with oil-supply, despite less power consumption.

• Journal of Electrical Engineering and Technology
• /
• 제2권4호
• /
• pp.485-493
• /
• 2007

This paper deals with the problem of detection of induction motor incipient faults. Artificial Neural Network (ANN) approach is applied to detect two types of incipient faults (1). Interturn insulation and (2) Bearing wear faults in single-phase induction motor. The experimental data for five measurable parameters (motor intake current, rotor speed, winding temperature, bearing temperature and the noise) is generated in the laboratory on specially designed single-phase induction motor. Initially, the performance is tested with two inputs i.e. motor intake current and rotor speed, later the remaining three input parameters (winding temperature, bearing temperature and the noise) were added sequentially. Depending upon input parameters, the four ANN based fault detectors are developed. The training and testing results of these detectors are illustrated. It is found that the fault detection accuracy is improved with the addition of input parameters.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1059-1062
• /
• 2003

Micro-tensile testing system has been developed and micro-tensile tests for copper foil have been carried out. The system consisted of a micro tensile loading system and a micro-ESPI system for measuring strain. The loading system has a maximum loading capacity of 50N and a stroke resolution of 4.5nm. Stress-strain curves for the electro-deposited copper foil with the thickness of 18$\mu\textrm{m}$ were obtained, and tensile properties, including elastic modulus, yielding strength and tensile strength, were determined. The tensile properties obtained under three different conditions of testing speed showed a dependency on the speed.