• 대한치과보철학회지
• /
• 제34권1호
• /
• pp.31-69
• /
• 1996

The purpose of this investigation was to analyze stress distribution in implant supporting tissue according to different types of attachments such as combination bar attachment, Hader bar attachment, O-Ring attachment and Dal-Ro attachment that are used in mandibular overdenture by using two osseointegrated implants, to study the influence that POM IMC used in bar type attachment has in implant supporting tissue and compare the preceding analyses to find out an effective stress distribution method. Three dimensional photoelastic method was used to obtain the following results. (A) Analysis of stress distribution according to attachment type 1. Under vertical load condition, compressive stress was seen at implant supporting area of working side on all the photoelastic models but in Hader bar attachment tensional stress was seen at distal upper area of implant supporting area. Relatively Hader bar and O-Ring attachment showed even stress distribution pattern. 2. Under vertical load condition, compressive stress at implant apex area and tensional stress at implant lateral supporting area were seen at nonworking side of all models. 3. Under $25^{\circ}$ lateral load condition, general compressive stress was seen at working side implant supporting area in most of the models, especially at distal upper supporting area higher compressive stress concentration was seen in combination bar attachment and tensional stress concentration, in Hader bar attachment. 4. Under $25^{\circ}$ lateral load condition, compressive stress at implant apex area and tensional stress at implant lateral supporting area were seen at nonworking side of all models, except O-Ring model which showed compressive stress only. (B) Influence of POM IMC to stress distribution in bar type attachment 5. Under vertical load condition, better stress distribution pattern was seen at working side of combination bar and Hader bar attachment model using POM IMC. 6. Under vertical load condition, stress value was increased at nonworking side of combination bar attachment model using POM IMC and tendency of increasing compression was seen at nonworking side of Hader bar attachment model using POM IMC. 7. Under $25^{\circ}$ lateral load condition, better stress distribution pattern was seen at working side of combination bar attachment model using POM IMC but tendency of increasing stress was seen on working side of Hader bar attachment model using POM IMC. 8. Under $25^{\circ}$ lateral load condition, stress reduction was seen at nonworking side of combination bar attachment model using POM IMC but tendency of increasing stress was seen at nonworking side of Hader bar attachment model using POM IMC.

• 항공우주기술
• /
• 제3권2호
• /
• pp.149-159
• /
• 2004

축방향 인장 및 압축하중을 받는 점탄성층을 갖는 복합재료 적층보의 동력학적 거동을 해석하였다. 개선된 지그재그 보이론과 지배방정식에 기초한 기하학적 상관식을 이용하여 점탄성층을 갖는 복합재료 적층보를 모델링하였고 이에 기초한 보 유한요소를 개발하였다. 축방향 인장 및 압축하중하의 고유진동수와 감쇠계수는 복소수 유일법을 이용하여 계산하였다. 축방향 인장 및 압축하중이 고유진동수 및 감쇠계수에 미치는 영향을 조사하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.850-853
• /
• 2008

In the motorized retractor of the smart seat belt system, anti-overload clutch is a very important element to prevent the excessive belt tensional force. Anti-overload clutch is the essential device to protect drivers from chest damage by the excessive belt tension. It generates slipping motion under excessive webbing moment and the belt tensional force is limited below critical value. In this study, slipping mechanism in the antioverload clutch is investigated by analysis and experiment. On the prototype model, finite element analysis is performed to identify the slipping condition and to determine the critical load. Analysis result is compared with the experimental result and the validity of the analysis model is verified. The purpose of the study is to provide the analytical background for the systematic design of the anti-overload clutch mechanism.

• 대한치과보철학회지
• /
• 제36권2호
• /
• pp.203-244
• /
• 1998

The human mandible is always under the condition of loading by the various forces extorted by the attached muscles. The loading is an important condition of the stomatognathic system. This condition is composed of the direction and amount of forces of the masticatory muscles, which are controlled by the neuromuscular system, and always influenced by the movement of both opening and closing. Mandible is a strong foundation for the teeth or various prostheses, nevetheless it is a elastic body which accompanies deformation by the external forces on it. The elastic properties of the mandible is influenced by the various procedures such as conventional restorative treatments, osseointegrated implant treatments, reconstructive surgical procedures and so forth. Among the treatments the osseointegrated implant has no periodontal ligaments, which exist around the natural teeth to allow physiologic mobility in the alveolar socket. And so around the osseointegrated implant, there is almost no damping effect during the transmission of occlusal stress and displacements. If the osseointegrated implants are connected by the superstructure for the stabilization and effective distribution of occlusal stresses, the elastic properties of mandible is restricted according to the extent of 'splinting' by the superstructure and implants. To investigate the change of elastic behaviour of the mandible which has osseointegrated implant prosthesis of various numbers of implant installment and span of superstructre, a three dimensional finite element model was developed and analyzed with conditions mentioned above. The conclusions are as follows : 1. The displacements are primarily developed at the area of muscle attachment and distributed all around the mandible according to the various properties of bone. 2. The segmentation in the superstructure has few influence on the distribution of stress and displacement. 3. In the load case of ICP, the concentration of tensional stress was observed at the anterior portion of the ramus($9.22E+6N/m^2$) and at the lingual portion of the symphysis menti($8.36E+6N/m^2$). 4. In the load case of INC, the concentration of tensional stress was observed at the anterior portion of the ramus($9.90E+6N/m^2$) and the concentration of tensional stress was observed at the lingual portion of the symphysis menti($2.38E+6N/m^2$)). 5. In the load case of UTCP, the relatively high concentration of tensional stress($3.66E+7N/m^2$) was observed at the internal surface of the condylar neck.

• 콘크리트학회논문집
• /
• 제16권5호
• /
• pp.581-589
• /
• 2004

본 논문에서는 일정진폭 휨인장 및 쪼갬인장 반복하중을 받는 콘크리트의 피로신뢰성과 모델제안을 위하여 도로포장에 사용되는 콘크리트를 대상으로 연구하였다. 실험데이터는 2-모수 Weibull 확률분포함수를 사용하여 신뢰성 해석을 수행하였고, 적합도 검정을 통하여 이를 기반으로 한 모델을 제시하였다. 피로실험은 $150 mm{\times}75 mm$ 시험체의 쪼갬인장피로 실험방법과 $150 mm{\times}150 mm{\times}550 mm$ 시험체의 휨인장피로 실험방법을 적용였으며 일정 진폭 피로하중에 대하여 수행하였다. 두 가지의 실험방법에 대하여 응력 수준 90, 80, $70\%$로 변화하여 실험하고 이때 적용한 응력비는 0.1, 하중재하속도 20Hz, 정현파(sine)를 적용하였다. 연구결과 콘크리트 피로데이터의 분산성으로 인하여 보다 정확한 해석을 위해 두 가지의 해석 기준을 설정하여 제시하였으며, 그래픽방법, 모멘트방법 및 최우도법에 의해 2-모수 Weibull의 매개변수 $\alpha$와 u를 계산하고 이를 이용하여 확률밀도함수(P.D.F)와 누적분포함수(C.D.F)를 도시하였다. 또한, Weibull의 확률분포함수를 이용한 신뢰성 해석은 Kolmogorov-Smirnov의 방법을 사용하여 $5\%$의 유의수준에서 적합도 검정을 수행한 결과 채택되는 것으로 나타났다. 이러한 해석에 기초하여 쪼갬인장피로실험과 휨인장피로 실험에 대한 피로모델을 제시하고 응력수준에 따른 피로수명과 200만회 및 1,000만회에서의 피로강도를 산정하여 제시하였으며 국외의 주요 피로모델과 비교하였다.

• Structural Engineering and Mechanics
• /
• 제9권4호
• /
• pp.323-338
• /
• 2000

An analytical approach for the prediction of the behaviour of steel-fiber reinforced concrete beams subjected to torsion is described. The analysis method employs a special stress-strain model with a non-linear post cracking branch for the material behaviour in tension. Predictions of this model for the behaviour of steel-fiber concrete in direct tension are also presented and compared with results from tests conducted for this reason. Further in this work, the validation of the proposed torsional analysis by providing comparisons between experimental curves and analytical predictions, is attempted. For this purpose a series of 10 steel-fiber concrete beams with various cross-sections and steel-fiber volume fractions tested in pure torsion, are reported here. Furthermore, experimental information compiled from works around the world are also used in an attempt to establish the validity of the described approach based on test results of a broad range of studies. From these comparisons it is demonstrated that the proposed analysis describes well the behaviour of steel-fiber concrete in pure torsion even in the case of elements with non-rectangular cross-sections.

• 대한구순구개열학회지
• /
• 제12권1호
• /
• pp.21-32
• /
• 2009

Generally, an adult cleft lip or/and palate patient shows some amount of maxillary deficiency due to limitation of bony growth caused by heavy scars resulted from previous operations such as a cheiloplasty and/or a palatoplasty at an early child age. To solve the problem, advancement of the maxilla is usually required during orthognathic surgery. However, severe tensional force resulted from heavy scars on the palate and/or the lip, as well as the bony defect at the cleft area limited sufficient advancement of the maxillary segment and finally caused relapse of the reposed maxilla. Therefore, distraction osteogenesis of the maxilla was introduced for the successful maxillary advancement inthose kinds of patients. As both hard and soft tissues can be simultaneously and gradually extended with this technique, tensional force caused by heavy scars opposed to forward movement of the maxilla can be reduced to an extent not to develop severe relapse of the advanced maxilla. Since distraction osteogenesis of the maxilla was applied as one of standard protocols for the treatment of the patients with severe maxillary hypoplasia dueto cleft lip and/or palate, the devices for the distraction was improved to control the vectors of distraction with better and more stable. We have treated a 23-year-old male cleft patient with a severe maxillary hypoplasia using a newly developed a maxillary distraction device and a RP model for a pre-operative simulation surgery. As a result, we could successfully move the maxilla as we designed pre-operatively and also reduce much of operation time. Therefore, we report of the case to share our experience with colleagues.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제34권2호
• /
• pp.151-156
• /
• 2008

Different kinds of forces can be applied to the biological tissue. The analysis of the applied force is highly important to explain the mechanism of cellular response. In this study, the applied force to the collagen gel was analyzed by the finite elements analysis. The model received two different kinds of static force (compression and tension). The force range was 50g to 400g. In results, von Mises stress was concentrated in the peripheral region in the compression model. It was concentrated in the central area in the tension model. However, the compressive force was high in the peripheral area of the compression model and the tensional force was also high in the same area of the tension model. In conclusion, the applied force could be different to the region and it should be considered in the experiment to analyze the effects of the mechanical force on the cells.

• 대한기계학회논문집A
• /
• 제26권11호
• /
• pp.2342-2354
• /
• 2002

The present study has numerically predicted both the flow -induced and thermally-induced residual stresses and birefringence in injection o. injection/compression molded center -gated disks. Analysis system for entire molding process was developed based on an ap propriate physical modeling including a nonlinear viscoelastic fluid model, stress-optical law, a linear viscoelastic solid model, free volume theory for density relaxation phenomena and a photoviscoelasticity and so on. Part I presents physical modeling a nd typical numerical analysis results of residual stresses and birefringence in the injection molded center-gated disk. Thermal residual stress was found to be extensional near the center, compressive near the surface and tend to become toward tensional at the surface. A double-hump profile was obtained across the thickness in birefringence distribution: nonzero birefringence is found to be thermally induced, the outer peak is due to the shear flow and subsequent stress relaxation during the filling stage a nd the inner peak is due to the additional shear flow and stress relaxation during the packing stage. Predicted birefringence including both the flow -induced and thermally-induced one becomes quite similar to the experimental one.

• Computers and Concrete
• /
• 제22권6호
• /
• pp.573-592
• /
• 2018

An analytical methodology for the calculation of the flexural and the shear capacity of concrete members with Fibre-Reinforced-Polymer (FRP) bars as tensional reinforcement is proposed. The flexural analysis is initially based on the design provisions of ACI 440.1R-15 which have properly been modified to develop general charts that simplify computations and provide hand calculations. The specially developed charts include non-dimensional variables and can easily be applied in sections with various geometrical properties, concrete grade and FRP properties. The proposed shear model combines three theoretical considerations to facilitate calculations. A unified flexural/shear approach is developed in flow chart which can be used to estimate the ultimate strength and the expected failure mode of a concrete beam reinforced with longitudinal FRP bars, with or without transverse reinforcement. The proposed methodology is verified using existing experimental data of 138 beams from the literature, and it predicts the load-bearing capacity and the failure mode with satisfactory accuracy.