• E2M - 전기 전자와 첨단 소재
• /
• 제9권3호
• /
• pp.277-283
• /
• 1996

The temperature dependent characteristics of hydrogenerated amorphous silcon thin film transistor (a-Si:H TFT) with a bottom gate of N-Type <100> Si wafer were investigated. Drain current on the hysteresis characteristic curve showed an exponential variation. Hysteresis area of TFT increased with the gate voltage increased and decreased with the small gate voltage. According to the variation of gate voltages, drain current of TFT increased by temperature increase, and hysteresis characteristics mainly depended on the temperature increase. The hysteresis current showed negative characteristics curve over 383K. The hysteresis occurance area and the differences of forward and reverse sweep were increased at the higher temperature. Hysteresis current of I$_{d}$(on/off) ratio decreased at the lower temperature and increased at the higher temperature.e.

• 전기의세계
• /
• 제28권9호
• /
• pp.43-50
• /
• 1979

Silicon nitride films were chemically deposited on silicon substrates by reacting SiCl$_{4}$ and NH$_{3}$ in a nitrogen atmosphere at 700~1100 .deg.C. The deposition rate increased rapidly with deposition temperature upto about 1000 .deg.C, and became less temperature dependent above this temperature. The etch rate of films in buffered HF solution decreased, with an increase of deposition temperature, and a heat treatment at a temperature higher than that of the deposition considerably reduced the etch rate. It indicates that the heat treatment resulted in a densification of the films. Surface charge density of 3~4 * 10$^{11}$ /cm$^{2}$ was determined from the C-V characteristics of MNS diode, and it was also found that surface charge density depended on deposition temperature, but not film thickness. The current-voltage characteristics displayed a logI-V$^{1}$2/ dependence in the temperature range of 300~500.deg.K. Measurement of the slope of this characteristics and its dependence on temperature and bias polarity suggest that conduction in sili con nitride films arises from the Poole-Frenkel mechanism.

• The Korean Journal of Ecology
• /
• 제15권2호
• /
• pp.127-135
• /
• 1992

The effects of nacl concentration, temperatura, light and growth regulator(GA3, kinetin) on the tuber germination of s. maritimus were investigated. The germination percentage increased with decreasing nacl, showing salt tolerance through time, and with increasing temperature untile 20~30oC light / dark (12/12 hr) of optimal temperature. The multiplication of nacl and temperature on germination percentage and velocity, increased significantly in higher temperature than lower temperature in saline. The germination percentage showed high value in dark condition than in light condition which is the charracteristics of underground organ. and ga3 act as germination stimulator to overcome the inhibitory effect of nacl. The effect of ga3 showed significant differances on tubers of s. maritimus of germination but that of kinetin had a litter sffects on germination. Factors of nacl and temperature interacted significantly and the effects of nacl on germination percentage and velocity depended on temperature condition.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2000년도 학술발표회 발표논문집
• /
• pp.302-307
• /
• 2000

The wintering honey bee chambers were constructed and inside environment factors were analyzed to provide high technology for efficient wintering of honeybee colonies. As a result of this study, inside air temperature of yongin chamber under the wide range of outside temperature condition was found to be appropriated for wintering of bee, and inside temperature of beehive was about 2$^{\circ}C$ higher than the air temperature in the chamber. The fan operation schedule did not control the high temperature down properly in the chamber, It was necessary to find a new fan operation schedule to be able to provide the optimum temperature for wintering honey bee colonies. inside humidity variation of Yongin chamber was very much depended on outside humidity.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1992년도 춘계학술대회 논문집
• /
• pp.34-38
• /
• 1992

Low temperature device processing has become of great interest within the last few years. In such low temperature processes, SiO$_2$films formed by Plasma-enhanced chemical vapor deposition (PECVD) have been studied. PECVD SiO$_2$films were formed with substrate temperature, and annealing time and temperature of RTP changed, and its'characteristics were obsreved by C-V measurement. We found that the quality of SiO$_2$films formed by PECVD depended on annealing time rather than substrate temperature.

• 환경위생공학
• /
• 제13권3호
• /
• pp.72-78
• /
• 1998

For investigation into gas permeation characteristics, the porous alumina membrane with asymmetrical structure, having upper layer with 10 nanometer under of pore diameter and lower layer with 36 nanometer of pore diameter, was prepared by anodic oxidation using DC power supply of constant current mode in an aqueous solution of sulfuric acid. The aluminium plate was pre-treated with thermal oxidation, chemical polishing and electrochemical polishing before anodic oxidation. Because the pore size depended upon the electrolyte, electrolyte concentration, temperature, current density, and so on, the the membranes were prepared by controling the current density, as a very low current density for upper layer of membrane and a high current density for lower layer of membrane. By control of current quantity, the thicknesses of upper layer of membranes were about $6{\;}{\mu}m$ and the total thicknesses of membranes were about $80-90{\;}{\mu}m$. We found that the mechanism of gas permeation depended on model of the Knudsen flow for the membrane prepared at each condition.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1153-1154
• /
• 2006

Effects of sintering conditions such as sintering temperature and heating rate on oxygen content, density, microstructure and toughness of sintered Mo were investigated. The oxygen content of the sintered Mo significantly depended on the sintering conditions. The oxygen content of the primary sintered(below 1673 K) Mo influenced the densifications. The number of pores at grain boundaries of the secondary sintered(at 2073 K)Mo depended on the oxygen content of the primary sintered Mo. Grain growth of the secondary sintered Mo was inhibited by the existence of pores at the grain boundaries. The secondary sintered Mo having larger number of pore and smaller grain size demonstrated higher strength.

• 한국안전학회지
• /
• 제7권1호
• /
• pp.13-19
• /
• 1992

Supercritical fluid technology was applied to the regeneration of industrial catalyst contaminated with toxic materials. The regeneration process of activated loaded with phenol was proposed, then the adsorphon tower was packed with the activated carbon-bed. Phenol diffuses into supercritical carbon dioxide(SCC) through the micro-pore and voldge of the activated carbon. The saturated solubility of phenol in SCC depended on the density of SCC varing with temperature and pressure conditions. Therefore, the fasile phase equilibrium calculation model of dxpanded liquid One was proposed, and equilibrium solubility of phenol in SCC was calculated using the model theoretically. The regeneration mechanism of activated carbon was analysed by degree of saturation of phenol and diffusion in SCC. The solubility prediction was more satisfactory for the wide range of SCC density than the dense gas model and the desorption of phenol depended on the degree of saturation of phenol in SCC.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.37-41
• /
• 2002

Thermal characteristics of hydrostatic guideway is largely depended on the temperature of supplied oil. For improving the positioning accuracy of hydrostatic guideway, relationship between setting temperature of oil cooler and thermal characteristics is analyzed, and influence of thermal characteristics on positioning accuracy is also analyzed experimental1y in this paper. Laser scale which has 0.01 $\mu\textrm{m}$ of resolution is used as feed-back unit. From the experimental results, it is confirmed that positioning error and repeatability is minimize upto 0.21 $\mu\textrm{m}$ and 0.18 $\mu\textrm{m}$ when the temperature of supplied oil is setting equal to temperature of atmosphere, and also confirmed that thermal deformation, which occurs by the temperature deviation between table and rail or scale supporter, works as limit of repeatability in long time operation.

• 대한기계학회논문집A
• /
• 제23권7호
• /
• pp.1215-1222
• /
• 1999

It is advantageous to use an NDE method to assess the mechanical properties of materials since the conventional method is time-consuming and sometimes requires cutting of sample from the material/component. This paper shows that the ultrasonic and the Barkhausen noise(BHN) methods can be used to accurately characterize forged reactor vessels. The attenuation coefficient of the ultrasonic wave was changed with heat treatment temperature and condition[as-quenched, tempered, PWHT]. The RMS[root mean square] voltage of Barkhausen noise depended on heat treatment temperature and conditions. The fracture appearance transition temperature(FATT) can be predicted using nondestructive evaluation methods.