• Journal of the Korean Magnetics Society
• /
• v.23 no.2
• /
• pp.49-53
• /
• 2013

A current sensor is one of important component which is used for the electrical current measurement during charge and discharge of the battery, and monitoring system of the motor controller in the electric and hybrid vehicle. In this study, we have developed an open loop type current sensor using GaAs Hall sensor and magnetic core has an air gap. The Hall sensor detect magnetic field produced by the current to be measured. The 3 mm air gap core was made by HGO electrical steel sheets after slitting, winding, annealing, molding, and cutting. Developed current sensor shows 0.03 % linearity within DC current range from -400 A to +400 A. Operating temperature range was extended to the range of $-40{\sim}105^{\circ}C$ using temperature compensating electronic circuit. To Improve frequency bandwidth limit due to the air flux of PCB (Printed Circuit Board) and Hall sensor, We employed an air flux compensating loop near Hall sensor or on PCB. Frequency bandwidth of the sensor was 100 kHz when we applied sine wave current of $40A{\cdot}turn$ in the frequency range from 100 Hz to 100 kHz. For the dynamic response time measurement, 5 kHz square wave current of $40A{\cdot}turn$ was applied to the sensor. Response time was calculated time reach to 90 % of saturation value and smaller than $2{\mu}s$.

• Food Science and Preservation
• /
• v.15 no.4
• /
• pp.491-496
• /
• 2008

To develop a freshness indicator of Chonggak-kimchi for marketing purposes, Chonggak-kimchi was prepared and pH, total acidity, total aerobic bacterial load, lactic acid bacterial levels, and reducing sugar content were measured. Sensory evaluation tests on product stored at $4^{\circ}C,\;10^{\circ}C,\;and\;20^{\circ}C$, were performed. The pH increased slightly early in storage, and then decreased to pH 4.2-4.3 for all samples. The rate of decrease of pH rose with increasing storage temperature. Total acidity values rapidly increased after 1, 5, and 7 days of storage at $20^{\circ}C,\;10^{\circ}C,\;and\;4^{\circ}C$, respectively. Populations of total aerobic bacteria and lactic acid bacteria increased slightly until 4 days, 10 days, and 30 days of storage at $20^{\circ}C,\;10^{\circ}C,\;and\;4^{\circ}C$, respectively, and then decreased drastically. Sensory evaluation data showed that Chonggak-kimchi was edible until 4 days(pH 4.5), 10 days(pH 4.4), and 30 days(pH 4.3) of storage at $20^{\circ}C,\;10^{\circ}C,\;and\;4^{\circ}C$, respectively. These results clearly suggest that the shelf-life of Chonggak-kimchi depends on storage temperature, and the pH limit for marketing is 4.3; this is a freshness indicator for Chonggak-kimchi.

• Korean Journal of Materials Research
• /
• v.3 no.5
• /
• pp.553-561
• /
• 1993

In this study, thr effect of $Bi_2O_3$ and BN addition as grain boundary modifiers on sintering and electrical properties of semiconducting PTCR(Positive Temperature Coefficient of Resistivity) mate rial were analyzed using TMA, XRD and Complex Impedance Spectroscopy method. Bismut.h Ox~de and Boron Nitride were added to Y-doped $BaTiO_3$ respectively. Bismuth sesquioxide up to O.lmol%solubil~ ty limit of $Bi_2O_3$ in Y--$BaTiO_3$ ceramics-retarded densification and grain growth, and further addition mitigated these retardation effects. The resistivity at room temperature increased with increasing amount of $Bi_2O_3$ and thus decreased the PTCR effect, probably due to the $Bi_2O_3$ segregation on the grain boundaries. From the complex ~mpedance pattern, it is known that the grain boundary resisitivity is dominant on the whole resistivity of sample. In the result of applying the defect chemistry, $Bi^{3+} \;and \; Bi^[5+}$ are substituted for Ua and Ti site, respectively. Boron nitride decomposed and formed liquid phase among the $BaTiO_3$ grains. The decomposed com~ ponents made the second phase and existed the tr~ple juntion from the result of EPMA. From the complex impendencc pattern, the gram and grain boundary resistivity were small. The grain size increased with increasing BN contents, and decreased grain boundary resistivity enhanced the PTCR effect.

• KEPCO Journal on Electric Power and Energy
• /
• v.2 no.2
• /
• pp.143-165
• /
• 2016

The amount of greenhouse gas emission reduction based on INDCs (Intended Nationally Determined Contributions) submitted to UN by each party is not sufficient to achieve the Paris Agreement's aim to "hold the increase in the global average temperature to well below $2^{\circ}C$ above pre-industrial levels and to pursue efforts to limit the temperature increase to $1.5^{\circ}C$" which was determined in the $21^{st}$ Conference of the Parties to the UNFCCC (COP 21). Accordingly, the emission reduction target of each party will be revised for the $2^{\circ}C$ goal. Among the several options to reduce the carbon emission, CCS (Carbon Capture and Storage) is a key option to curb $CO_2$ emissions from large emission sources such as fossil-based power plants, cement plants, and steel production plants. A large scale CCS demonstration projects utilizing $1^{st}$ generation $CO_2$ capture technologies are under way around the world. It is anticipated, however, that the deployment of those $1^{st}$ generation $CO_2$ capture technologies in great numbers without government support will be difficult due to the high capture cost and considerable increase of cost of electricity. To reduce the carbon capture cost, $2^{nd}$ and $3^{rd}$ generation technologies are under development in a pilot or a bench scale. In this paper, current status of large scale CCS demonstration projects and the $2^{nd}$ and $3^{rd}$ generation capture technologies are summarized. Novel capture technologies on wet scrubbing, dry sorbent, and oxygen combustion are explained in detail for all capture areas: post-combustion capture, pre-combustion capture, and new combustion technologies.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.3
• /
• pp.99-106
• /
• 1998

The performance of the turbofan engine, a medium scale civil aircraft which has been developing in Rep. of Korea, was analyzed and the control scheme for optimization the performance was studied. The dynamic and real-time linear simulation was performed in the previous study The result was that the fuel scedule of the step increase overshoot the limit temperature(3105 $^{\cire}R$) of the high pressure turbine and got small surge margine of the high pressure compressor. Therefore a control scheme such as the LQR(Linear Quadratic Regulator) was applied to optimizing the performance in this studies. The linear model was expected for designing controller and the real time linear model was developed to be closed to nonlinear simulation results. The system matrices were derived from sampling operating points in the scheduled range and then the least square method was applied to the interpolation between these sampling points, where each element of matrices was a function of the rotor speed. The control variables were the fuel flow and the low pressure compressor bleed air. The controlled linear model eliminated the inlet temperature overshoot of the high pressure turbine and obtained maximum surge margins within 0.55. The SFC was stabilized in the range of 0.355 to 0.43.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.2
• /
• pp.61-67
• /
• 2017

As transistor density increases rapidly, a heat flux from IC device rises at fast rate. Thermal issues raised by high heat flux cause IC's performance and reliability problems. To solve these thermal management problems, the conventional cooling methods of IC devices were reached their thermal limit. As a result, alternative cooling methods such as liquid heat pipe, thermoelectric cooler, thermal Si via and etc. are currently emerging. In this paper microchannel liquid cooling system with TSV was investigated. The effects of 2 coolants (DI water and ethylene glycol 70 wt%) and 3 metal bumps (Ag, Cu, Cr/Au/Cu) on cooling performance were studied, and the total heat flux of various coolant and bump cases were compared. Surface temperature of liquid cooling system was measured by infrared microscopy, and liquid flowing through microchannel was observed by fluorescence microscope. In the case of ethylene glycol 70 wt% at $200^{\circ}C$ heating temperature, the total heat flux was $2.42W/cm^2$ and most of total heat flux was from liquid cooling effect.

• Korean Journal of Materials Research
• /
• v.11 no.6
• /
• pp.453-459
• /
• 2001

It is important for the fabrication of nuclear cladding to optimize the microstructure, because the properties of Zr-based nuclear claddings such as mechanical properties, oxidation-resistance and corrosion- resistance vary widely with its microstructure. The microstructure in Zr-based alloy is strongly dependent on the solubility of alloying element. However, it is very difficult to measure the solubility due to the low solution limit of alloying elements in Zr-based alloy. In this study, Thermoelectric Power(TEP) measurements are used to determine the solubility of Nb in Zr-0.8Sn alloy, which is confirmed by optical microscopy and transmission electron microscopy. The solutioning of Nb obtained by a homogenization treatment and water-quench leads to a decrease of TEP The saturation of TEP appears with the increase of homogenization temperature, which means the saturation of the Nb content in the matrix. From these results, the solubility ($C_{Nb}$) of Nb in Zr-0.8Sn with temperature could be expressed as fellow equation : $4.69097{\times}10^{16}{\times}e^{-25300\times\;I/T}$(ppm.at.%)

• Applied Biological Chemistry
• /
• v.28 no.4
• /
• pp.252-260
• /
• 1985

The changes of the qualities and the components of 5 different Takju (Korean wine) in various stroage temperatures were evaluated. Commercial Takju didn't change in acidity and alcoholic degree at $5{\sim}10^{\circ}C$ for 36 hours. But at $30{\sim}35^{\circ}C$ the alcohollic degree has inversed to $5.0{\sim}7.0$. As time went by, pH nearly went down to pH 3.7 and went up back over 4.0. Amino acidity was risen continuously during the stroage terms and the change of reducing sugar was irregular. The number of vegetable cell of yeast in commercial Takju at $30{\sim}35^{\circ}C$ after 18 hours was $2.4{\times}10^8$, at $5{\sim}10^{\circ}C$ after 36 hours $2.4{\times}10^8$, and each of them was reduced below $1{\times}10^8$ after exceeding the limit of shelf-life. Number of general bacteria was increased suddenly in a high temperature at the first and it was decreased afterwards, but the tendency of increase and decrease was slow in a low temperature. It was possible to keep the quality for 5 days at $5{\sim}10^{\circ}C$ in case of commercial Takju and the shelf-life of pasteurized Takju was extended over 7 days.

• International Journal of Highway Engineering
• /
• v.9 no.4
• /
• pp.193-204
• /
• 2007

Deformation strength($S_D$) is a property which shows relatively good correlation with rut resistance of asphalt mixtures at high temperature. The Asphalt Pavement Analyzer (APA) is widely used as an equipment for estimating rut resistance of asphalt mixtures. The APA was used as corresponding property of the $S_D$ to estimate rutting resistance of asphalt mixtures. Many data were collected to establish the correlation of $S_D$ with APA. For $S_D$ test, the specimen is submerged into the $60^{\circ}C$ water for 30 minutes before applying a vertical load at the speed of 50mm/min to obtain peak load (P) and deformation (y) for $S_D$ calculation. For the same materials, APA test was performed. Relation of the $S_D$ with APA rut depth was evaluated using regression analysis. The $R^2$ value was 0.76, indicating this simple test procedure being a possible method for predicting deformation resistance of asphalt concretes at high temperature. It was also shown that, using the regression model, minimum value(s) of $S_D$ of surface course asphalt mixture or binder course for a particular road level can be determined. The limit values may be possible to use as cut-off value(s) of asphalt mixtures for the layer after further elaborated studies.

• Journal of Wetlands Research
• /
• v.15 no.1
• /
• pp.35-41
• /
• 2013

In this study, we tried to overcome a limit in cutting timing of reed culm by applying a plant hormone, indole-acetic acid (IAA) as a growth regulator with various contents ($10^{-3}$ M, $10^{-6}$ M, $10^{-9}$ M, $10^{-12}$ M). 19 shoots emerged from 240 segments of hardened reed culm from montane fen and eight out of the 19 shoots emerged by $10^{-6}$ M IAA treatment as the most in $5^{th}$ Sep. 2012. 50 shoots emerged from 60 segments of non-hardened reed culm from a population in Seoul National University transplanted from Mt. Odae by $10^{-6}$ M IAA treatment despite the cutting was performed about two weeks later ($19^{th}$ Sep.). Via third cutting experiment performed about 40 days later ($29^{th}$ Oct.), only two shoots out of 60 segments were observed by the same experimental condition except atmospheric temperature. It seemed likely that it was too low temperature in third experiment ($10^{\circ}C$) than the former experiments (about $20^{\circ}C$) to form adventitious buds from culm segment. We recommend to utilize the thick reed culm in culm cutting as possible because the thicker culm segment we used, the thicker emerged shoot we could observe (i.e., diameters of emerged shoots were about 20% of the planted segment's diameters).