• 한국해양공학회지
• /
• 제25권3호
• /
• pp.28-33
• /
• 2011

The thermal shock properties of SiC materials were investigated for high temperature applications. In particular, the effect of thermal shock temperature on the flexural strength of SiC materials was evaluated, in conjunction with a detailed analysis of their microstructures. The efficiency of a nondestructive technique using ultrasonic waves was also examined for the characterization of SiC materials suffering from a cyclic thermal shock history. SiC materials were fabricated by a liquid phase sintering process (LPS) associated with hot pressing, using a commercial submicron SiC powder. In the materials, a complex mixture of $Al_2O_3$ and $Y_2O_3$ powders was used as a sintering additive for the densification of the microstructure. Both the microstructure and mechanical properties of the sintered SiC materials were investigated using SEM, XRD, and a three point bending test. The SiC materials had a high density of about 3.12 Mg/m3 and an excellent flexural strength of about 700 MPa, accompanying the creation of a secondary phase in the microstructure. The SiC materials exhibited a rapid propagation of cracks with an increase in the thermal shock temperature. The flexural strength of the SiC materials was greatly decreased at thermal shock temperatures higher than $700^{\circ}C$, due to the creation of microcracks and their propagation. In addition, the SiC materials had a clear tendency for a variation in the attenuation coefficient in ultrasonic waves with an increase in thermal shock cycles.

• 한국자동차공학회논문집
• /
• 제25권3호
• /
• pp.297-308
• /
• 2017

One of the major engine thermal management system(TMS) strategies for improving fuel economy is to operate the engine in high temperatures. Therefore, this work performed a numerical and experimental study to examine the effect of several different STOs(Starting Temperature of Opening) of wax-thermostat, ranging from $85^{\circ}C$ to $105^{\circ}C$, of gasoline engine on fuel economy and emission characteristics. In this study, a gasoline car equipped with waxthermostat was tested and simulated under FTP-75 and HWFET mode. CRUISE $M^{TM}$ was used to simulate vehicle dynamics, transient engine performance and TMS. The test results showed fuel savings for both drive cycles due to higher STO of $100^{\circ}C$, which is slightly worse than that of $90^{\circ}C$ and amounts between 0.34 and 0.475 %. These controversial results are attributed to experimental errors and uncertainty. The computational results for three STOs, $85^{\circ}C$, $95^{\circ}C$ and $105^{\circ}C$, showed that fuel savings attributed to the application of higher STOs of $95^{\circ}C$ and $105^{\circ}C$ are relatively small and range from 0.306 to 0.363 %. It is also found that the amount of HC and CO emissions from the tailpipe tends to decrease with higher engine coolant temperature because of faster catalyst light-off and improved combustion.

• 공업화학
• /
• 제8권1호
• /
• pp.122-131
• /
• 1997

아연-티타늄 복합금속산화물 탈황제를 제조하여 석탄가스중의 $H_2S$를 제거하는 고온탈황성능을 연구하였다. $H_2S$ 흡수에 의한 탈황제의 황화반응실험을 충전층 관형 흐름반응기를 사용하여 $550{\sim}750^{\circ}C$ 범위에서 수행한 결과 탈황율과 아연성분의 손실측면에서 $650^{\circ}C$가 최적 황화반응 온도임이 밝혀졌다. SEM 분석에 의해서 $650^{\circ}C$에서의 황화반응과 $750^{\circ}C$에서의 재생반응에 따른 탈황제 입자의 구조변화를 관찰하였다. 탈황성능의 지속성과 탈황제 내구성을 평가하기 위하여 연속적인 황화-재생 cycle 반응실험을 수행하였으며 10번째 cycle 이후에 수거반 탈황제 시료의 특성을 BET, XRD, SEM/EDX에 의해서 분석하였다. 아연-티타늄 복합 산화물 탈황제는 연속적인 황화-재생 cycle 동안에 거의 일정한 탈황성능을 나타내었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.135-136
• /
• 2006

Bismuth titanate ($Bi_4Ti_3O_{12}$, BIT) thin film has been studied intensively in the past decade due to its large remanent polarization, low crystallization temperature, and high Curie temperature. Substitution of various trivalent rare-earth cations (such as $La^{3+}$, $Nd^{3+}$, $Sm^{3+}$ and $Pr^{3+}$) in the BIT structure is known to improve its ferroelectric properties, such as remanent polarization and fatigue characteristics. Among them, neodymuim-substituted bismuth titanate, ((Bi, Nd)$_4Ti_3O_{12}$, BNT) has been receiving much attention due to its larger ferroelectricity. In this study, Ferroelectric $Bi_{3.3}Nd_{0.7}Ti_3O_{12}$ thin films were successfully fabricated by liquid delivery MOCVD process onto Pt(111)/Ti/$SiO_2$/Si(l00) substrates. Fabricated polycrystailine BNT thin films were found to be random orientations, which were confirmed by X-ray diffraction and scanning electron microscope analyses. The remanent polarization of these films increased with increase in annealing temperature. And the film also demonstrated fatigue-free behavior up to $10^{11}$ read/write switching cycles. These results indicate that the randomly oriented BNT thin film is a promising candidate among ferroelectric materials useful for lead-free nonvolatile ferroelectric random access memory applications.

• 한국항공우주학회지
• /
• 제39권7호
• /
• pp.627-633
• /
• 2011

연료전지 무인기 탑재용 수소발생기의 온도환경변화에 따른 성능평가를 수행하였다. 수소 저장 및 발생을 위해 화학수소화물 중 수소함량이 높고 저장성이 우수한 수소화붕소나트륨($NaBH_4$)을 연료로 사용하였으며, 촉매를 이용한 가수분해반응을 통해 수소를 발생하였다. 수소발생기의 온도환경변화를 위한 저온 및 고온 챔버를 각각 준비하였으며, 온도범위는 $-20^{\circ}C$에서 $60^{\circ}C$까지 $20^{\circ}C$의 간격으로 설정하였다. 20과 25wt.%의 $NaBH_4$ 용액 농도에서 수소발생기의 수소발생률과 반응기와 분리기의 온도변화를 측정하였다. 수소 발생률은 반응주기가 반복될수록 감소하였으며, 저온 환경에서는 높은 수소발생률을 보였지만, 고온 환경에서는 수소발생률이 급격히 감소하였다. 수소발생률의 감소는 촉매유실과 촉매표면의 $NaBO_2$ 도포가 원인으로 확인되었다.

• The Korean Journal of Ceramics
• /
• 제3권4호
• /
• pp.263-268
• /
• 1997

RuO$_3$ thin films were deposited on Si(100) substrate at low temperatures by hot-wall metalorganic chemical vapor deposition. Bis(cyclopentadienyl) ruthenium, Ru$(C_5H_5)_2$, was used as the precursor RuO$_2$single phase was obtained at a low deposition temperature of 25$0^{\circ}C$ and the crystallinity of RuO$_2$thin films improved with increasing deposition temperature. RuO$_2$thin films grow perpendicularly to the substrate and show the columnar structure. The grain size of RuO$_2$films drastically increases with increasing the deposition temperature. The resistivity of the 180 nm-thick RuO$_2$thin films deposited at 27$0^{\circ}C$ was 136 $\mu$$\Omega$-cm and increased with decreasing film thickness. SrBi$_2Ta_2O_4$ thin films deposited by rf magnetron sputtering on the RuO$_2$bottom electrodes showed a fatigue-free characteristics up to ~10$^10$ cycles under 5 V bipolar square pulses and the remanent polarization, 2 P$_r$ and the coercive field, 2 E, were 5.2$\mu$C/$\textrm{cm}^2$ and 76.0 kV/cm, respectively, for an applied voltage of 5 V The leakage current density was about 7.0$\times$10$^{-6}$ A/$\textrm{cm}^2$ at 150 kV/cm.

• 대한치과기공학회지
• /
• 제33권3호
• /
• pp.193-202
• /
• 2011

Purpose: The aim of this study was to evaluate the effect of pre-treatment of core and hydrothermal treatment on the bond strength and flexural strength of ceramic veneered zirconia. Methods: 3Y-TZP specimens(KaVo Zr, $25mm{\times}3mm{\times}1mm$)were prepared by five pre-treatment methods and divided into seven groups including control two groups, subsequently the specimens veneered with the E-MAX ceram according to manufacturer's information(total specimen thickness 1.5mm). Two groups from ceramic-zirconia specimens(n=105, n=15 per group)were assigned into two experimental fatigue conditions, namely storage in an autoclave at $134^{\circ}C$ for 5h, thermo-cycling(3,000cycles, between 5 and $55^{\circ}C$, dwell time 45s, transfer time 2s). A flexural strength test was performed in a universal testing machine(crosshead speed: 0.5mm/min). Data were statistically analyzed using one-way ANOVA and Tukey's test(${\alpha}$=0.05). Results: The ceramic-zirconia bond strength value for liner application group(LLW, $27.3{\pm}3.8$) were significantly lower than those of the pre-treatment groups($30.72{\pm}5.3$). The ceramic-zirconia bond strength and zirconia flexural strength was not affected by thermo-cycling(p>0.05), whereas it was affected by storage in an autoclave at $134^{\circ}C$ for 5h(p<0.05). Conclusion: The results indicated that the ceramic-zirconia bond strength and zirconia flexural strength was affected by low temperature degradation.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2000년도 High Temperature Superconductivity Vol.X
• /
• pp.111-120
• /
• 2000

Recently, metal oxide films such as MgO or ZrO$_2$ have been studied as buffer layers to fabricate the superconductor with preferred orientation and as diffusion barriers to prevent the reaction between superconductor and metal substrate. In this research, we focused fabrication and characterization of MgO and ZrO$_2$ films on textured metal substrates. We fabricated MgO and ZrO$_2$ films on the Ni metal sheets by sol-gel dipping method. The microstrcures of the films were investigated by SEM and AES analyses. The films were coated with different cycles and dryed at 400$^{\circ}$C and 500$^{\circ}$C . The final films were heat-treated at 700$^{\circ}$C, 800$^{\circ}$C, and 1000$^{\circ}$C, in air atmosphere. We investigated the alignment of MgO and ZrO$_2$ films on Ni metal sheets by XRD and pole figure. The grain growth of metal oxide films was improved by the increase of the drying temperature and annealing temperature. The grain growth was increased with the annealing temperature. The alignment of metal oxide films depended on the thickness.

• 마이크로전자및패키징학회지
• /
• 제17권3호
• /
• pp.27-32
• /
• 2010

Cu pillar 범프와 Sn 패드로 구성된 플립칩 접속부를 형성한 후, Sn 패드의 높이에 따른 Cu pillar 플립칩 접속부의 열 싸이클링 및 고온유지 신뢰성을 분석하였다. Cu pillar 플립칩 접속부를 구성하는 Sn 패드의 높이가 5 ${\mu}m$에서 30 ${\mu}m$로 증가함에 따라 접속저항이 31.7 $m{\Omega}$에서 13.8 $m{\Omega}$로 감소하였다. $-45^{\circ}C{\sim}125^{\circ}C$ 범위의 열 싸이클을 1000회 인가한 후에도 Cu pillar 플립칩 접속부의 접속저항의 증가가 12% 이하로 유지되었으며, 열 싸이클링 시험전과 거의 유사한 파괴 전단력을 나타내었다. $125^{\circ}C$에서 1000 시간 유지시에도 Cu pillar 플립칩 접속부의 접속저항의 증가가 20% 이하로 유지되었다.

• Journal of the Korean Data and Information Science Society
• /
• 제28권6호
• /
• pp.1437-1445
• /
• 2017

환경시험의 목적은 시험대상 제품이 수명주기 중 겪을 수 있는 환경에 노출되었을 때 정상적인 기능을 수행할 수 있도록 설계 제조되었는지를 시험 평가하는 것이다. 본 논문은 한반도 연해안지역에서 운용할 군수장비의 운용환경조건에 대한 온도시험의 설계 기준을 제안한다. 온도기준은 과도하거나 과소하지 않게 합리적으로 설계되어야하는데 본 연구에서는 한반도 해안지역에서 가장 더웠던 지역과 가장 추웠던 지역을 기준으로 고온 및 저온에 대한 다양한 백분위별 발생빈도를 제시하여 사용군이 선택할 수 있도록 한다. 1904년부터 2015년까지 한반도 28개 연해안 지역 관측지점의 기온 자료를 분석한 결과 1개월 기준으로 가장 더운 지역은 포항, 가장 추운 지역은 신의주로 확인되었다. 한반도 해안 환경에서 고온과 저온의 1% 발생빈도값은 각각 $37.7^{\circ}C$와 $-23.7^{\circ}C$로 추정되었다. 아울러 상대습도, 풍속, 태양복사를 포함하는 고온과 저온의 일주기표도 제시한다.