• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.895-898
• /
• 1997

These days, most of new materials, which is in use widely as cutting process materials have a characteristic in common. That is hard cutting. So, it happens that hardness by cutting temperature. And hardness on cutting process has an effect on tool wear or life shortness of tools. To solve these problems hot-machining is proposed. When a material is heated, organization of material is soften. So cutting process becomes easy. When such a hot-machining method applies on drilling process and then heated material is processed, cutting force is less than usual drilling process cutting force. In this paper, when a material is heated, cutting force on drilling process is measured. It is decided that the best suitable temperature area. And it suggest that the better hot-machining condition as surface accuracy is measured.

• 전기전자학회논문지
• /
• 제11권3호
• /
• pp.122-128
• /
• 2007

Sinusoidal voltage-controlled oscillators (VCOs) based on Colpitts and Hartley oscillators are presented. They consist of a LC parallel-tuned circuit connected in a negative-feedback loop with an OTA-R amplifier and two diode limiters, where the inductor is simulated one realized with temperature-stable linear operational transconductance amplifiers (OTAs) and a grounded capacitor. Prototype VCOs are built with discrete components. The Colpitts VCO exhibits less than 1% nonlinearity in its current-to-frequency transfer characteristic from 4.2 to 21.7 MHz and ${\pm}$95 ppm/$^{\circ}C$ temperature drift of frequency over 0 to $70^{\circ}C$. The total harmonic distortion (THD) is as low as 2.92% with a peak-to-peak amplitude of 0.7 V for a frequency-tuning range of 10.8-32 MHz. The Hartley VCO has the temperature drift and THD of two times higher than those of the Colpitts VCO.

• 한국태양에너지학회 논문집
• /
• 제34권2호
• /
• pp.66-72
• /
• 2014

Ground source heat pump system can achieve high efficiency of performance by utilizing annually constant underground temperature to provide heat source for space heating and cooling. Generally, the depth of constant-temperature zone under the ground depends on surface heat flux and soil properties. The deeper the ground heat exchanger is installed, the higher the heat exchange rate can be acquired. However, in order to optimally design the system, it is necessary to consider both the installation cost and the system performance. In this study, performance analysis of ground source heat pump system according to the depth has been conducted through the case study.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.43-46
• /
• 2007

To find out the optimum design of hydrogen storage and supply tank using Metal Hydride (briefly MH) and to make clear the performance characteristics under various conditions are our research purpose. In order to use the low-temperature exhaust heat, $LaNi_{4.7}Al_{0.3}$ which operates under the low pressure of 1MPa is chosen, and we measure the basic properties, namely density, specific heat, PCT(Pressure-Concentration-Temperature) characteristic, and effective thermal conductivity. Then, a numerical calculation model of hydrogen storage using MH alloy is suggested and this thermal diffusion equation of model is solved by the backward difference method. This calculation results rate compared with the experimental results of the systems which installed 1kg MH alloy and, it is found out that our calculation model can well predict the experimental results. By the experimental using MH alloy, it is recognized that the hydrogen flow rate can control by the step adjustment of brine temperature.

• 한국정밀공학회지
• /
• 제10권2호
• /
• pp.138-145
• /
• 1993

The bath cryostat of cryogenic apparatuses which are generally used to study physical phenomena under low temperature and ultra low temperature has been desigened and constructed. The practical use of the cryostat is verified by the measurement of the storage life of liquid heloum and liquid nitrogen vessels. The cryostat consists of triple structure of high vacuum environment in order to minimize the evaporation rate of liquid helium and liquid nitrogen by thermal conductivity and radiant heat. The minimum thickness which can stand against inner and outer pressures is calculated from considering the strength of the material.

• Journal of Welding and Joining
• /
• 제15권3호
• /
• pp.56-64
• /
• 1997

Macrostructural characteristic of the transverse cracks and fatigue behavior were studied for EH 32 TMCP 50mm thick plate welded with FACW under the variation in preheat and interpass temperatures. Transverse cracks were detected in specimen welded with preheat and interpass temperature below $30^{\circ}C$, but cracks were not detected in the specimens welded with preheat and interpass temperatures at the range of $100~120^{\circ}C$.C. The location of crack formation was found to strongly depend upon the thickness of weld layers as regard to the plate thickness.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제15권2호
• /
• pp.249-254
• /
• 2015

Solution-derived amorphous indium-gallium-zinc oxide (a-IGZO) thin-film-transistor (TFTs) were developed using a microwave irradiation treatment at low process temperature below $300^{\circ}C$. Compared to conventional furnace-annealing, the a-IGZO TFTs annealed by microwave irradiation exhibited better electrical characteristics in terms of field effect mobility, SS, and on/off current ratio, although the annealing temperature of microwave irradiation is much lower than that of furnace annealing. The microwave irradiated TFTs showed a smaller $V_{th}$ shift under the positive gate bias stress (PGBS) and negative gate bias stress (NGBS) tests owing to a lower ratio of oxygen vacancies, surface absorbed oxygen molecules, and reduced interface trapping in a-IGZO. Therefore, microwave irradiation is very promising to low-temperature process.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 제2회 학술대회 논문집 일렉트렛트 및 응용기술전문연구회
• /
• pp.59-63
• /
• 2000

BSCCO thin films are fabricated via a co-deposition process by an ion beam sputtering with an ultra-low growth rate, and sticking coefficients of the respective elements are evaluated. The sticking coefficient of Bi element exhibits a characteristic temperature dependence : almost a constant value of 0.49 below $730^{\circ}C$ and decreases linearly with temperature over $730^{\circ}C$ This temperature dependence can be elucidated from the evaporation and sublimation rates of bismuth oxide, $Bi_2O_3$, from the film surface. It is considered that the liquid phase of the bismuth oxide plays an important role in the Bi(2212) phase formation in the co-deposition process.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.74-76
• /
• 2004

This paper deals with the analytical method to calculate the high temperature demagnetization characteristics of a high-speed machine with diametrically magnetized permanent magnet rotor. The equivalent magnetic circuit model is used to analyze the magnet operating point on high temperature condition. Agreements have been obtained between the results of the analytical model and finite-element analysis on prototype high-speed motors.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.144-147
• /
• 2000

A numerical method for the solution of one-dimensional inverse heat conduction problem is established and its performance is demonstrated with computational results. The present work introduces the maximum entropy method in order to build a robust formulation of the inverse problem. The maximum entropy method finds the solution that maximizes the entropy functional under given temperature measurement. The philosophy of the method is to seek the most likely inverse solution. The maximum entropy method converts the inverse problem to a non-linear constrained optimization problem of which constraint is the statistical consistency between the measured temperature and the estimated temperature. The successive quadratic programming facilitates the maximum entropy estimation. The gradient required fur the optimization procedure is provided by solving the adjoint problem. The characteristic feature of the maximum entropy method is discussed with the illustrated results. The presented results show considerable resolution enhancement and bias reduction in comparison with the conventional methods.