• Journal of the Optical Society of Korea
• /
• v.18 no.6
• /
• pp.788-792
• /
• 2014

It has been a critical issue to reduce the size of spectrometers in many fields such as on-chip chemical and biological sensing. The proposed plasmonic channel-waveguide with a sub-micrometer width has a cutoff frequency which enables us to control wavelength dependent propagation properties. We focused on the capability of the waveguide for spectral-to-spatial mapping when the waveguide width changes gradually. In this paper, we propose a plasmonic tapered channel-waveguide structure as a compact spectrometer with a physical size of $0.24{\times}2.0{\times}0.20{\mu}m^3$. The scattering point just above the tapered waveguide moves linearly depending on the wavelength of the injecting light. The spectral-to-spatial mapping can be improved by increasing the tapered length.

• ETRI Journal
• /
• v.29 no.6
• /
• pp.811-813
• /
• 2007

We report on a ridge waveguide laser diode with laterally tapered waveguides fabricated in a single growing step using a double patterning method. In this structure, nearly constant output power is obtained with the change of the lower tapered waveguide width, and the facet power ratio of 1.4 to 1.5 is observed over the current range. The asymmetric facet power property is also investigated.

• Journal of the Optical Society of Korea
• /
• v.14 no.4
• /
• pp.337-341
• /
• 2010

A high sensitivity fiber optic temperature sensor based on a side-polished fiber (SPF) coupled to a tapered multimode overlay waveguide (MMOW) is proposed and studied. Both tapered and non-tapered MMOW were considered to study the effect of tapering of MMOW on the characteristics of the device and to investigate the criticality of the uniformity of the multimode overlay waveguide over the SPF. Present study shows that tapering of the MMOW can be used to tune the desired wavelength range without any loss in the sensitivity. Sensitivity up to 9 nm/$^{\circ}C$ within the temperature range of 25 to $100^{\circ}C$ can be achieved with the proposed sensor, almost 6 times higher compared even to state-of-the-art high-sensitivity grating-based fiber optic temperature sensors.

• Journal of electromagnetic engineering and science
• /
• v.18 no.4
• /
• pp.248-253
• /
• 2018

An electromagnetic boundary-value problem of a tapered rectangular waveguide is rigorously solved based on eigenfunction expansion and the mode-matching method. Scattering parameters of the tapered rectangular waveguide are represented in a series form and calculated in terms of different rectangular waveguide combinations. Computation is performed to analyze reflection and transmission characteristics. Conductor loss by surface current density is also calculated and discussed.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.87-90
• /
• 2000

In this paper. we present a method for a systematic design of a dielectric slab polarizer in the circular waveguide. This structure is realized using a tapered dielectric slab inside a circular waveguide. Commercial software is used to obtain the equivalent dielectric constant of the circular waveguide partially filled with a dielectric slab. The length of the tapered region is determined so that the reflection from the dielectric slab is sufficiently low. A polarizer operating at 10 GHz band is designed, fabricated and tested.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.1338-1342
• /
• 2006

This paper presents the theoretical approach to describe the wave propagation in the waveguide with varying cross-section. The waveguides considered in this paper are stepped-rod, tapered-rod, and stepped rod with a tapered section at the middle of wave-transmission. The wave transmission ratio for displacement, stress, and power was calculated for these three rods. The distribution of the stress and displacement along the stepped rod with a tapered section was calculated and compared with the results obtained by FEM analysis.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.3
• /
• pp.156-161
• /
• 2014

We have investigated the optical properties of plamonic waveguide with tapered structure based on InP material for photonic integrated circuit(PIC). The proposed plasmonic waveguide is covered with the Ag thin film to generate the plasmonic wave on metallic interface. The optical characteristics of plasmonic waveguide were calculated using the three-dimensional finite-difference time-domain method. The plasmonic waveguide was fabricated with the lengths of 2 to $10{\mu}m$ and the widths of 400 to 700 nm, respectively. The plasmonic mode and optical loss were measured. The optimum plasmonic length is $10{\mu}m$ and widths are 600 and 700 nm in the fabricated waveguide. This plasmonic waveguide can be directly integrated with other conventional optical devices and can be essential building blocks of PIC.

• Korean Journal of Optics and Photonics
• /
• v.34 no.6
• /
• pp.235-240
• /
• 2023

The optical signal injected into an end-fire optical phased array propagates along the waveguides inside the device and is emitted from the edge of the antenna. In general, reflection and scattering occur at the boundary, thereby reducing the emission efficiency of the optical signal. In this article, we propose a silicon nitride (Si₃N₄) tapered waveguide antenna structure whose width is tapered toward the emitting edge, achieving high emission efficiency operating at the 1,550 nm wavelength. The Si₃N₄ tapered waveguide antenna was numerically designed using the 3D finite-difference time-domain method. The optical signal emission efficiency increased from 78% to 96.3%, while reflectance decreased from 22% to 3.7% compared with the untapered waveguide antenna counterpart. This result will not only boost the optical signal intensity but also mitigate optical noise resulting from back reflection along the waveguide in the end-fire optical phased array device.

• Korean Journal of Optics and Photonics
• /
• v.15 no.1
• /
• pp.22-27
• /
• 2004

In this paper, we designed a mode size converter to reduce coupling loss between optical waveguide and single mode fiber. The proposed mode converter is composed of periodically segmented tapered waveguide to achieve small size and easy fabrication. For the optimally designed mode size converter at 1550nm, the taper length is 500(equation omitted), the segmentation period 5ß:, the waveguide width of fiber contact section 1.3ß:, and duty cycle 0.95. The coupling loss of the optimized mode size converter is 0.33㏈/point, which is 1.27㏈/point lower than that without the mode size converter.

• Journal of the Optical Society of Korea
• /
• v.1 no.1
• /
• pp.44-47
• /
• 1997

The integration of a GaAs/AlGaAs multi-quantum well electroabsorption modulator and a tapered waveguide vertical direction optical interconnect has been performed without the complicated regrowth process. Zn impurity-induced layer disordering of MQW layer is used to achieve the energy transfer between SQW and MQW regions. Light coupled into a SQW region was transferred to an MQW region and an intensity modulation of 10 dB extinction ratio was demonstrated.