• Progress in Superconductivity and Cryogenics
• /
• v.5 no.1
• /
• pp.35-39
• /
• 2003

A typical HTS power transmission cable has multi-layer conductor structure to increase the current capacity. The tapes of the innermost layer are wound on a round former, and adjacent tapes of another layer are separated by a thin insulating film. However, usually the current is not evenly distributed among the layers because of inductance difference of each layer, and the inductance is provided by the winding pitch of each layer's tape. Consequently n method to make the current distribution more uniform is a adjusting the tape winding pitch, hence reduce the AC loss. This paper describes a current distribution by adjusting a tape winding pitch of each layer. Also, this paper shows recommendations for future cable conductor prototypes.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.12
• /
• pp.1112-1117
• /
• 2006

The properties of LTCC green tape with addition of binder were investigated in order to understand an effects of binder on multilayer processing. A green sheet form was fabricated through tape casting method with the MLS-22 powder. The lamination density increased with increasing amount of binder and lamination pressure. With increasing amount of binder, the elongation of ceramic sheets increased but the tensile stress and air-permeability decreased. The addition of excessive binder is caused defects in the green sheet during via hole punching. The optimum condition of the via hole without defects was observed from amount of the binder 10 wt%.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1136-1141
• /
• 2003

Among various methods to manufacture the PDP barrier ribs, the pressing and the roll forming methods are simple and economical because they form the ribs by utilizing the plastic flow of the green tape in a relatively short time without generating air-polluting dusts. In the present study, the roll forming method was investigated by experiments as well as numerical analyses and in result the groove roll and the preform were designed. The effect of draft angle, comer radius, and initial thickness of the green tape on the plastic flow was examined by a series of parametric studies. The preform was recommended to ease the plastic flow into the grooves and to avoid the occurrence of crack during rolling and sintering processes.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.2
• /
• pp.81-88
• /
• 2014

Synthetic products such as casting tape and splints are rapidly replacing conventional plaster casts to treat orthopedic patients. Most synthetic products are produced through a polymerization process with related chemical agents. In this study, the effect of the process parameters on the residual NCO content within a prepolymer for casting tape and the hardening temperature for casting tape were experimentally evaluated. In order to verify the effects of the process parameters, an experimental method was adopted. From an S/N ratio analysis, optimal parameter combinations were determined to produce a pre-polymer with a suitable residual NCO content and alower hardening temperature. Prediction models for the NCO content and the hardening temperature were developed and confirmed.

• Progress in Superconductivity and Cryogenics
• /
• v.14 no.3
• /
• pp.28-32
• /
• 2012

The critical current of the HTS(High Temperature Superconductor) tape is governed by cooling temperature, magnetic field and its angle to HTS tape originated from its geometrical structure. At the HTS coil design stage, the critical current of the coil is calculated by considering the Ic-B characteristics of the 2G tape and the operating current is determined based on the critical current. The operating current and the structure of the 5 T coil are suggested through the FEM (Finite Elements Method) analysis and calculation. As a part of our on-going research on a 20 T LTS/HTS magnet, we have designed and constructed a 5 T HTS insert coil and tested it in liquid helium temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.295-299
• /
• 1996

In order to investigate the relation between the microstructure and the V-I characteristics of HTSC wire, single and 19 filamentary silver-sheathed Bi2223 tapes were fabricated using the powder-in-tube method. Higher J$\_$c/ at 77.3 K(0 T) and 4.2 K(in magnetic field) can be achieved for the 19 filamentary Bi tape, comparing the single filamentary tape. However, the I$\_$c/ distribution of 19 filamentary Bi2223 tape was found to be wider by analyzing the curve obtained from 2nd differential of V-I data. This was considered to be resulted from worse uniformity of oxide filament due to severe cold working.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.7 no.2
• /
• pp.13-20
• /
• 1970

The dispersion characteristics of tape meander line were analyzed by electromagnetic field theory. The several different tape meander lines were photoetched on copper printed-bakelit substrate, and these tape meander line structures were inserted into the X-band waveguide. Phase bridge method was used for the dispersion characteristics measurement of meanderline. The measured. results were plotted on diagram(Brillouin diagram) and compared with theoretical values. Measured results were consistent with theoretical Values. But, on the measured diagram, passband midfrequency was lower than theoretical value. It was believed that the discrepancy was due to the backelite loading. The group velocity of stagger tuned meander line was higher than that of uniform meander live, and the freqnency band of constant group velocity of stagger tuned meanderline was sider than that of uniform meander line.

• Journal of the Korean Ceramic Society
• /
• v.37 no.8
• /
• pp.824-831
• /
• 2000

Alumina tapes, having various ratios of alumina to alumina＋binder＋plasticizer (a/(a＋o)) and binder to binder＋plasticizer(b/(b＋p)), were prepared by the tape casting method. The tapes were thermocompressed varying the thermocompression parameters such as temperature, pressure, and duration time. Among the parameters, the pressure was the most influential to the tape packing density. The packing density varied in two different ways depending on the a/(a＋o) ratio. For the tapes having low a/(a＋o) ratio, a saturation density was reached by applying very a low pressure of 1 MPa. For tapes with high a/(a＋o), on the contrary, the saturation density was obtained at a relatively high pressure. These different responses to the pressure are attributed to the fact that the rearrangement of alumina particles by the pressure becomes easy as an organic content in the tapes is high.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.3
• /
• pp.247-253
• /
• 2000

We evaluated the electric properties of Bi-2223 jointed tapes processed by both resistive-and superconducting-joint methods. For resistive-joint. filler materials of wood metal Pb/Sn. In and silver paste were used whereas for superconductive-joint lap joint method was used. In the resistive joint tape. critical transport property(CCR) n-value and contact resistance were observed to be in the range of 10-85% 1-8,9. and 0.71x10$\^$-6/-0.13x10$\^$-6/Ω, respectively. depending on their filler materials. Specifically it is believed that the electrical properties of resistive joint tape are significantly related to the resistivity of filler materials. On the other hand the CCR of superconductin joint type was varied 55 to 85% with uniaxial pressure probably due to the irregular microstructure in the transition region.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.10
• /
• pp.2082-2088
• /
• 2002

Among various methods to manufacture the PDP barrier ribs, the pressing and the roll forming methods are simple and economical because they form the ribs by utilizing the plastic flow of the green tape in a relatively short time without generating air-polluting dusts. In the present study, the roll forming method was investigated by experiments as well as numerical analyses and in result the groove roll and the preform were designed. The effect of draft angle, corner radius, and initial thickness of the green tape on the plastic flow was examined by a series of parametric studies. The preform was recommended to ease the plastic flow into the grooves and to avoid the occurrence of cracks during rolling and sintering processes.