• Journal of Electrical Engineering and Technology
• /
• v.6 no.4
• /
• pp.551-555
• /
• 2011

The Crab label tag with a loop matching feed and a modified dipole antenna structure was proposed. The antenna impedance is conjugated easily to a radio frequency identification IC chip impedance by a loop matching feed. The reading range of the crab structure tag is 0.9-1.0 m from the upper side of the formula milk can lid. The fabricated label tag size is $44.0{\times}44.0mm^2$. The operating frequency at -3 dB return loss is 861.0-929.0 MHz, and the maximum reading range at the anechoic chamber is 1.5 m.

• ETRI Journal
• /
• v.28 no.2
• /
• pp.216-218
• /
• 2006

This letter presents the design for a low-profile planar inverted-F antenna (PIFA) that can be stuck to metallic objects to create a passive radio frequency identification (RFID) tag in the UHF band. The designed PIFA, which uses a dielectric substrate for the antenna, consists of a U-slot patch for size reduction, several shorting pins, and a coplanar waveguide feeding structure to easily integrate with an RFID chip. The impedance bandwidth and maximum gain of the tag antenna are about 0.3% at 914 MHz for a voltage standing wave ratio (VSWR) of less than 2 and 3.6 dBi, respectively. The maximum read range is about 4.5 m as long as the tag antenna is on a metallic object.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.9B
• /
• pp.1092-1097
• /
• 2011

An anti-collision protocol which tries to minimize the collision probability and identification time is the most important factor in all identification technologies. This paper focuses on methods to improve the efficiency of tag's process in identification systems. Our scheme, Binary Slotted Query Tree (BSQT) algorithm, is a memoryless protocol that identifies an object's ID more efficiently by removing the unnecessary prefixes of the traditional Query Tree (QT) algorithm. With enhanced QT algorithm, the reader will broadcast 1 bit and wait the response from the tags but the difference in this scheme is the reader will listen in 2 slots (slot 1 is for 0 bit Tags and slot 2 is for 1 bit Tags). Base on the responses the reader will decide next broadcasted bit. This will help for the reader to remove some unnecessary broadcasted bits which no tags will response. Numerical and simulation results show that the proposed scheme decreases the tag identification time by reducing the overall number of request.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.12B
• /
• pp.1452-1458
• /
• 2009

In this paper, Our proposed Multipurpose Complex Card UHF band RFID small-size Tag antenna. Multi purpose Complex Card UHF band RFID small-size Tag antenna that is to minimize the low efficiency of RFID Tag Read Range that generates space limitation and a conductor surrounded by inducing fingerpring system with dual(HF, UHF) Card is presented. Our proposed UHF band RFID small-size Tag antenna is for the Multipurpose Complex Card that is mounted on the fingerpring system as well as the HF Tag. It also enables to minimize and facilitates Tag chip matching by adjusting Tapered, Meander line and Loop structure. Given the card substance properties and periphery circuit, the proposed small-size Tag antenna, in this report, is designed with PET film with size of $50{\times}15mm^2$. The RFID small-size Tag method for measurements is used by EPCglobal Static Test instrument in Anechoic Chamber, which is tested with dual Card, within the car and in wallet. It is found that Read Range is 3.8m from the EPCglobal Static Test, Maximum Read Range within the car from the field test results in 7.6m. Proposed Tag antenna is will be used in the parking control security system.

• Journal of Electrochemical Science and Technology
• /
• v.1 no.1
• /
• pp.39-44
• /
• 2010

1.5 V and 3.0 V-class film-type primary batteries were designed for radio frequency identification (RFID) tag. Efficient fabrication processes such as screen-printings of conducting layer ($25{\mu}m$), active material layer ($40{\mu}m$ for anode and $80{\mu}m$ for cathode), and electrolyte/separator/electrolyte layer ($100{\mu}m$), were adopted to give better performances of the 1.5 V-class film-type Leclanch$\acute{e}$ primary battery for battery-assisted passive (BAP) RFID tag. Lithium (Li) metal is used as an anode material in a 3.0 V-class film-type $MnO_2||$Li primary battery to increase the operating voltage and discharge capacity for application to active sensor tags of a radio frequency identification system. The fabricated 3.0 V-class film-type Li primary battery passes several safety tests and achieves a discharge capacity of more than 9 mAh $cm^{-2}$.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.62-67
• /
• 2005

Object recognition in the field of robotics generally has depended on a computer vision system. Recently, RFID(Radio Frequency IDentification) technology has been suggested to support recognition and has been rapidly and widely applied. This paper introduces the more advanced RFID-based recognition. A novel tag named 3D tag, which facilitates the understanding of the object, was designed. The previous RFID-based system only detects the existence of the object, and therefore, the system should find the object and had to carry out a complex process such as pattern match to identify the object. 3D tag, however, not only detects the existence of the object as well as other tags, but also estimates the orientation and position of the object. These characteristics of 3D tag allows the robot to considerably reduce its dependence on other sensors required for object recognition the object. In this paper, we analyze the 3D tag's detection characteristic and the position and orientation estimation algorithm of the 3D tag-based RFID system.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.5
• /
• pp.2134-2143
• /
• 2018

This work introduces a fault diagnosis method for transformer based on self-powered radio frequency identification (RFID) sensor tag and improved Hilbert-Huang transform (HHT). Consisted by RFID tag chip, power management circuit, MCU and accelerometer, the developed RFID sensor tag is used to acquire and wirelessly transmit the vibration signal. A customized power management including solar panel, low dropout (LDO) voltage regulator, supercapacitor and corresponding charging circuit is presented to guarantee constant DC power for the sensor tag. An improved band restricted empirical mode decomposition (BREMD) which is optimized by quantum-behaved particle swarm optimization (QPSO) algorithm is proposed to deal with the raw vibration signal. Compared with traditional methods, this improved BREMD method shows great superiority in reducing mode aliasing. Then, a promising fault diagnosis approach on the basis of Hilbert marginal spectrum variations is brought up. The measured results show that the presented power management circuit can generate 2.5V DC voltage for the rest of the sensor tag. The developed sensor tag can achieve a reliable communication distance of 17.8m in the test environment. Furthermore, the measurement results indicate the promising performance of fault diagnosis for transformer.

• Journal of Navigation and Port Research
• /
• v.33 no.1
• /
• pp.51-56
• /
• 2009

This paper presents the design of high sensitive/broadband tag antenna for Radio Frequency Identification (RFID) in Ultra High Frequency(UHF) band. A proposed tag antenna size is $60\;mm\;{\times}\;10\;mm\;{\times}\;1\;mm$. The resonant frequency is 910MHz and bandwidth is about 900 MHz at -10 dB below. The measured return loss and directional pattern have been confirmed a good agreement with the calculation results. The read range of proposed tag antenna with chip is observed about 6.5 m and proposed tag antenna has been observed an average 0.5 m for more than read range of the commercial tag antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.2
• /
• pp.93-98
• /
• 2018

This paper introduces the development of HF(NFC) and UHF band(13.56 MHz, 920 MHz) tag antennas, imbedded in a box. In dual band antennas, the HF band tag can be used to inspect the box using NFC, and the UHF band tag can be used for logistics. The dielectric constant of the box material is measured and used for simulation. The Ntag213 chip manufactured by NXP is used in HF loop antennas, since NFC is possible with Ntag213. For the UHF band, the Higgs-3 chip manufactured by Alien is used. The HF tag antenna is located at the center of the UHF tag antenna, and the location of the HF tag antenna is calculated while considering coupling effects. The designed tag can be used by both the bands for the purposes of logistics and authentication.

• ETRI Journal
• /
• v.31 no.4
• /
• pp.376-386
• /
• 2009

An active radio frequency identification (RFID) system has the advantages of a long identification distance and a good identification rate, overcoming passive RFID drawbacks. Therefore, interest in the development of active RFID systems has been gradually increasing in areas of harbor logistics and national defense. However, some identification failures between active RFID systems developed under the same standards have been reported, presumably due to a lack of development of accurate evaluation methods and test equipment. We present a realization of the hardware and software of an emulator to evaluate the standard conformance of an active RFID system in a fully anechoic chamber. The performance levels of the designed emulator are analyzed using Matlab/Simulink simulations, and the applicability of the emulator is verified by evaluating the standard conformance of a real active RFID tag. Finally, we propose a new evaluation method by incorporating a self-running test mode environment into the RFID tags to reduce testing time and increase testing accuracy. The application of the suggested method to actual tags improves measurement uncertainty by 0.56 dB over that obtained using existing methods.