Since the digital TV signal band is very wide ($54{\sim}806MHz$), the VCO used in the frequency synthesizer must also have a wide frequency tuning range. Multiple LC VCOs have been used to cover such wide frequency band. However, the chip area increases due to the increased number of integrated inductors. A general method for achieving both reduced VCO gain(Kvco) and wide frequency band is to use the switched-capacitor bank LC VCO. In this paper, a scheme is proposed to cover the full band using only one VCO. The RF VCO block designed using a 0.18um CMOS process consists of a wideband LC VCO with reduced variation of VCO gain and frequency steps. Buffers, divide-by-2 circuits and control logics the simulation results show that the designed circuit has a phase noise at 100kHz better than -106dBc/Hz throughout the signal band and consumes $9.5{\sim}13mA$ from a 1.8V supply.
Rf magnetron sputtering을 이용하여 InP, GaAs 기판위에 ZnO 박막을 증착시켰다. 진공 ampul 및 $Zn_3P_2$ 분위기 하에서 열처리 과정을 통해 P와 As을 ZnO 박막내에 도핑하였으며, 박막의 전기적 특성 측정 결과 정공의 농도가 $10^{16}cm^{-3}-10^{19}cm^{-3}$ 으로서 p-형 전기전도도를 나타내었다. XRD 측정을 통하여 ZnO 박막의 내부에 이상이 존재하지 않는다는 것을 확인하였다. 또한 FESEM을 이용하여 p-형 ZnO 박막의 표면을 관찰하였으며 그 위에 n-형 ZnO 박막을 sputtering을 이용하여 증착시켜 I-V 특성을 관찰하였다. 본 실험을 통해 P 및 As의 확산을 통한 p-형 ZnO 박막의 성장이 가능하였으며, I-V 특성으로부터 ZnO의 발광소자 및 자외선 검출기로의 응용이 가능함을 확인하였다.
A new spatial localization technique using high-order surface gradient coil (SGC) is proposed. Although the Spatial Selection with High-Order gradient (SHOT) can provide a 2-D selection with only one selective RF pulse, the high-order gradient produced by cylindrical-shape coils has not been clinically useful for clinical systems due to the large minimum selection size caused by the limited radial gradient intensity. However, by using the proposed high-order SGCs located near the imaging region, the size of volume selection can be reduced to a clinically useful 1-4 cm in diameter by applying stronger radial gradient with much less gradient driving power. A 40 cm-by-40 cm $r^{2}$ SGC has been designed and constructed, and phantom and volunteer studies have been performed. Experimental results using spatially localized MRI show good agreement to the theoretically predicted behavior.
We presented a channel model for the inter vehicle radio link including the reflection from the road surface, side road vehicle and concrete wall. Then we theoretically derived the path loss and delay profile characteristics using the Ray tracing method efficiently analyzing millimeter wave or optic wave. Finally, we shown the improvement of propagation characteristics by diversity techniques, BCH coding and convolution coding techniques. At the result, MRC diversity techniques and BCH coding can't obtained PER = $10^{-6}$ which is considered to be data service criterion. But, we knew that Packet Error Rate Characteristic can obtained PER = $10^{-6}$, which is considered to be data service criterion, when convolution coding scheme are adopted in Rician fading.
The relation between the height of ascending solvents and its velocity were studied with strips of Toyo No. 50 filter paper. The filter paper strip of 3cm width and cat 30 cm length is hooked down or fixed between two sheets of glass plates inside a cylinder containing the solvent, in which the lower end of the strip is dipped. As the solvents, acetone, hydrochloric acid, water or mixtures of these are used. For short time intervals, Ostwald's folmula $h = Kt^n$ was found to be most suitable to express the relation between the height of the solvent front, h, and time, t. For longer time intervals, results will be discussed in the next paper. The mean values of the constant m in the above formula for pure acetone and pure water were 0.44 and 0.485, respectively, and that of K were 0.05 and 2.4, respectively. The time interval whose the above formula applies, for each solvent was 2 hours for the former, and a half hour for the later, respectively. The movement of solutes, such as $Cu^{++}$ and $Fe^{++}$ showed that the Rf values of solutes become constant values after a long periods; e.g., ca. 6 hours with 10N-HCl-Acetone (1 : 9) solvent.
Kang, Jin-Suk;Jeon, Young-Jun;Sung, Mee-Young;Shin, Seung-Ho;Jeong, Tai-Keong T.
Journal of information and communication convergence engineering
/
v.5
no.4
/
pp.389-393
/
2007
The distribution of donated blood for medical purpose is an area that presents many challenges. In order to establish a comprehensive solution, the current patterns of distribution must be reviewed and problems related to it need to be clearly understood. This paper introduces 'Radio Frequency Identification (RFID) System', as a potential solution to some of the problems which arise in the process of blood supply distribution, and a way to systematically manage the blood supply. For the various possible RFID systems, the reader and tag must be suitable for the purpose of blood distribution. A database has been designed that can recognize tags and objects in a ubiquitous RFID blood distribution system. In this paper, we design the real-time software to control the RFID reader system and transponder, using the EEPROM memory by RFID. The experimental results confirm that the transmission rate of 3.9kbps for RF is 125 KHz. The electric power usage of transponder chip is $100{\mu}W$, with the recognition distance is about 7cm range.
Na, N.;Choi, J.;Han, T.;Ahn, D.;Lee, D.;Hong, Y.;Hwang, I.
Proceedings of the KIEE Conference
/
2001.11c
/
pp.380-382
/
2001
This paper presents the implementation of IEEE 802.11 Medium Access Control and Physical Layer Protocol that can be applied to wireless LAN system. We have used PRISM2 chipsets from Intersil to build the baseband, IF, and RF parts. DSSS(Direct Sequence Spread Spectrum) physical layer at 2.4GHz ISM band is adopted in the hardware prototype. To meet the high-speed requirement of physical layer, we have designed the MAC protocol layer with embedded firmware and FPGA. The prototype board is shown to be able to support the physical layer of 5GHz and 600Hz wireless LAN systems.
Journal of Advanced Marine Engineering and Technology
/
v.32
no.6
/
pp.964-973
/
2008
In this study, a short-wavelength coplanar-type transmission line employing periodic ground structure (PGS) was developed for application to miniaturized on-chip passive component on Si Radio Frequency Integrated Circuit (RFIC). The transmission line employing PGS showed shorter wavelength and lower characteristic impedance than conventional coplanar-type transmission line. The wavelength of the transmission line employing PGS structure was 57 % of the conventional coplanar-type transmission line on Si substrate. Using the theoretical analysis. basic characteristics of the transmission line employing PGS (e.g., bandwidth. loss, impedance, and resonance characteristics) were also investigated in order to evaluate its suitability for application to a development of miniaturized passive on-chip components on silicon RFIC. According to the results. the bandwidth of the transmission line employing PGS was more than 895 GHz as long as T is less than 20${\mu}m$, and the resonance characteristic was observed in 1239 GHz, which indicates that the PPGM structure is a promising candidate for application to a development of miniaturized on-chip passive components on Si RFIC.
Journal of the Society of Naval Architects of Korea
/
v.51
no.3
/
pp.212-219
/
2014
As subsea production has been revived up, the demand of subsea equipment has also been increased. Among the equipment, subsea tree plays a major role in safety. The tubing hanger is one of the most important components in subsea tree. In this study structural reliability analysis on dual bore tubing hanger of subsea tree is performed. The target reliability which is introduced in ISO regulation is used for judging whether tubing hanger is safe or not. The considered loads are working pressure, working temperature and suspended tubing weight. Thermal-stress analysis on tubing hanger is performed and kriging model is created based on the results of FEM analysis. According to von Mises criterion, limit state equation can be estimated. Reliability analysis is performed by using level 2 method and the result is verified by that of Monte Carlo Simulation. For finding most probable failure point, enhanced HL-RF method is adopted. Because the reliability of model doesn't reach target reliability, an improvement measure should be considered. Thus, it is suggested to change the material of tubing hanger main body to AISI 4140.
Proceedings of the International Microelectronics And Packaging Society Conference
/
2003.11a
/
pp.53-58
/
2003
The Wafer Level Packaging is one of the most important technologies in the semiconductor industry today. Its primary advantages are its small form factor and low cost potential for manufacturing including test procedure. The CASIO's WLP samples, application example and the structure are shown in Fig.1, 2&3. There are dielectric layer , under bump metal, re-distribution layer, copper post , encapsulation material and terminal solder .The key technologies are 'Electroplating thick copper process' and 'Unique wafer encapsulation process'. These are very effective in getting electrical and mechanical advantages of package. (Fig. 4). CASIO and CMK are developing a new System Packaging technology called the Embedded Wafer Level Package (EWLP) together. The active components (semiconductor chip) in the WLP structure are embedded into the Printed Wiring Board during their manufacturing process. This new technical approach has many advantages that can respond to requirements for future mobile products. The unique feature of this EWLP technology is that it doesn't contain any solder interconnection inside. In addition to improved electrical performance, EWLP can enable the improvement of module reliability. (Fig.5) The CASIO's WLP Technology will become the effective solution of 'KGD problem in System Packaging'. (Fig. 6) The EWLP sample shown in Fig.7 including three chips in the WLP form has almost same structure wi_th SoC's. Also, this module technology are suitable for RF and Analog system applications. (Fig. 8)
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.