• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.438-442
• /
• 2001

Much attention has given to EMI effects created by variable speed ac drive system. This paper focuses on the switching technique to mitigate common mode voltage. Zero switching states of inverter control invoke large common mode voltage. Using inversed carrier wave, zero switching states are removed. In addition, proposed technique is easy to apply to existing 2-level inverter design. And common mode mitigation technique for sinusoidal PWM is also presented. Proposed switching technique is implemented with a 2.2kw 1735rpm induction motor.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.5
• /
• pp.530-535
• /
• 2004

We have studied 90$^{\circ}$ twisted nematic mode switching by fringe electric field(F-TN mode) using a liquid crystal (LC) with negative dielectric anisotropy. In the device, two polarizers are parallel each other, electrodes exist only on bottom substrate, and one of rubbing direction is coincident with polarizer axis. Therefore, the cell shows a black state before a voltage is applied. With a bias voltage generating fringe-electric field, the LC twists perpendicular to fringe electric field such that the LCs are almost homogeneously aligned except near the bottom surface since the negative type of the LC is used. Consequently, the new device exhibits much wider viewing angle than that of the conventional TN mode due to in-plane switching and relatively high transmittance since the LC director above whole electrode area aligns parallel to the polarizer axis.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.5
• /
• pp.425-430
• /
• 2006

To meet an increasing demand for high performance in gun dynamic plant, both a precise and a fast response positioning are strongly required for the gun servo system. A mode switching control(MSC) scheme, which includes a fine stabilizing controller, fast positioning one and a switching function, is widely used to meet this requirement. Stabilization is performed through PID controller, while a time optimal control method is used for target designation. In this paper, a modified PTOS(Proximate Time Optimal Servomechanism) algorithm is derived so as to accommodate the damping term in the gun plant model. Also, applying a mode switching strategy, the bumpless transfer is made possible when the controller switches from PTOS to PID. To show the effectiveness of the overall control system, simulation results are given including the gun dynamics.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.493-498
• /
• 2004

The EMI noise source in a switching mode power supply is dominated by a common mode noise. If we can understand the common mode noise occurring mechanism, it is resulted to find out the method to suppress the EMI noise source in the switching mode power supply. The common mode noise is occurring mostly due to circuit is unbalanced which is caused by the capacitive coupling to frame ground, which passes through a heatsink of the switching devices. This research paper presents a new effective balancing method of buck converter circuit by mean of grounding the parasitic and compensation capacitors in correct proportion which is called that the common mode impedance balance (CMIB). The CMIB can be achieved by source, transmission line and termination balanced, such balancing, the common mode current will be cancelled out in the frame ground. The greatly reduced common mode noise can be confirmed by the experimental results.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.215-217
• /
• 2009

The authors propose a novel dual mode liquid crystal display (LCD) which has both dynamic and memory operating LCD modes. The mode uses a horizontal switching and bistable chiral splay nematic (BCSN) LCD. The proposed dual mode does not require pixeldivision and has a higher aperture ratio and resolution than the previously proposed dual mode. Experimental results of the memory and dynamic mode show a high contrast ratio of over 100:1.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.3
• /
• pp.243-249
• /
• 2001

This paper proposes a full wave mode ZVT-PWM boost converter. The converter with the auxiliary switch in a full wave mode makes possible soft switching operation of all switches including the auxiliary switch whereas the auxiliary switch is turned off with hard switching in the conventional converter. Therefore, the proposed converter reduces the turn-off switching loss and switching noise of the auxiliary switch without additional passive and/or active elements and high power density system can be realized.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.12 no.1
• /
• pp.47-52
• /
• 2012

This paper focuses on discrete-time sliding mode control with SIIM fuzzy adaptive switching gain. The adaptive switching gain is calculated using the simplified indirect inference fuzzy logic. Two fuzzy inputs are the normal distance from the present state trajectory to the switching function and the distance from the present state trajectory to the equilibrium state. The fuzzy output $f_{out}$(k) out f k is used to adjust the speed the adaptation law depending on the location of the state trajectory. The simulation results showed that the proposed method had no chattering in case of uncertain parameter without disturbance. Moreover the convergent rate of the switching gain was faster and more stable even in case of disturbance.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.5-6
• /
• 2000

Fringe-field switching (FFS) technology exhibiting a high image quality has been developed. In this paper, one pixel concept, manufacturing process, materials, and electro-optic characteristics of FFS mode comparing with conventional in-plane switching mode, and its possible application to reflective type will be discussed.

• Journal of Power Electronics
• /
• v.16 no.6
• /
• pp.2327-2337
• /
• 2016

The mode-switching control of transient process is important to grid-connected 400 Hz solid-state power supply systems. Therefore, this paper analyzes the principle of on-grid and islanding operation of the system with or without local loads in the grid-connected process and provides a theoretical study of the effect of different switching sequences on the mode-switching transient process. The conclusion is that the mode switch (MS) must be turned on before the solid-state switch (STS) in the on-grid process and that STS must be turned off before the MS in the off-grid process. A strategy of mode-switching smooth control for transient process of the system is proposed, including its concrete steps. The strategy utilizes the average distribution of peak currents and the smooth adjustment of peak currents and phases to achieve a no-shock grid connection. The simulation and experimental results show that the theoretical analysis is correct and that the method is effective.

• Journal of Information Display
• /
• v.1 no.1
• /
• pp.9-13
• /
• 2000

In liquid crystal displays, the display mode that represents initial liquid crystal alignment and method of applying voltage, mainly determines the image quality of display. Recently we have developed the fringe-field switching (FFS) mode exhibiting high image quality. In this paper, a pixel concept, manufacturing process, materials, and electro-optic characteristics of the FFS mode comparing with conventional in-plane switching mode, and its possible application to reflective type are discussed.