• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.158-161
• /
• 1999

This Paper proposes the architecture of WDM(wavelength division multiplexed) based large scale photonic packet switch network, which is composed of the FC(frequency converter) and OM (output module). The features of the proposed WDM based photonic packet switch network are 2-stage switch network, and WDM based internal optical link that is connected between FC and OM. This paper evaluates the internal call blocking characteristics of the photonic packet switch network. In results, we confirmed that the proposed WDM based photonic packet switch network has the potentiality in the practical implementation.

• TTA Journal
• /
• s.87
• /
• pp.157-161
• /
• 2003

한국정보통신기술협회(TTA)는 2003년 3월 7일 대은전자㈜(http://www.dek.co.kr/) Gate Hub(모델명: DEK1521)의 성능시험을 수행하여 TTA Verified 인증서(번호: TTA-V-N-03-014)를 발급하였다. 또한 2003년 4월 3일 ㈜네오정보시스템(http://www.neoinfosys.co.kr/) 세대통신 분배장치(모델명: NIS - HM1616A)의 성능시험을 수행하여 TTA Verified 인증서(번호: TTA-V-N-03-026)를 발급하였다. 위의 두 장비는 Fast Ethernet Switch module과 전화 및 데이터 라인 연결 module을 함께 갖추었으며, TTA가 위의 두 장비를 이용하여 수행한 시험은 Fast Ethernet Switch module의 성능을 측정하는 것이었다. 본 고에서는 TTA가 마련한 Fast Ethernet Switch에 대한 인증기준(TTA-V-N-03-004-CC20)을 바탕으로 위의 두 장비에 대해 수행한 Fully meshed Throughput/Aging 시험 결과를 소개한다.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.2 s.35
• /
• pp.105-109
• /
• 2005

A compact antenna switch module for GSM/DCS dual band applications based on multilayer low temperature co-fired ceramic (LTCC) substrate is presented. Its size is $4.5{\times}3.2{\times}0.8 mm^3$ and insertion loss is lower than 1.0 dB at Rx mode and 1.2 dB at Tx mode. To verify the stability of the developed module to the process window, each block that is diplexer, LPF's and bias circuit is measured by probing method in the variation with the thickness of ceramic layer and the correlation between each block is quantified by calculating the VSWR In the mean while, two types of bias circuits -lumped and distributed - are compared. The measurement of each block and the calculation of VSWR give good information on the behavior of full module. The reaction of diplexer to the thickness is similar to those of LPF's and bias circuit, which means good relative matching and low value of VSWR, so total insertion loss is maintained in quite wide range of the thickness of ceramic layer at both band. And lumped type bias circuit has smaller insertion itself and better correspondence with other circuit than distributed stripline structure. Evaluated ceramic module adopting lumped type bias circuit has low insertion loss and wider stability region of thickness over than 6um and this can be suitable for the mass production. Stability characterization by probing method can be applied widely to the development of ceramic modules with embedded passives in them.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.15 no.4
• /
• pp.291-297
• /
• 2022

This Paper is about the study that design performance and reliability measurement circuits of the IPM which is an intelligent switching switch module included at an inverter circuits for driving of A.C. Servo motors in home appliance. IPM is a core device of motor driver and it's switching characteristics should be retained uniformly during the driving of a servo system. All of it's specification, the collector emitter switch on voltage Vce(on) spec. is very important. As the IPM are core part of inverters and producing from several brands and versions, for optimal performances of application systems a method and measurement & evaluation system to measure Vce(on) value, collector emitter switch on voltage, of the IPM IGBT switches with various brands are required. Especially, the proposed method can measure and evaluate Vce(on) values of IPM with load at mounting state on the motor driving circuits and proposed measurement & evaluation system can be important instrument systems for IPM user companies.

• International Journal of Internet, Broadcasting and Communication
• /
• v.12 no.3
• /
• pp.9-17
• /
• 2020

In this paper, as part of the research for the infrastructure of very high flexible and reconfigurable data center using very high speed crossbar switches, we developed a simulator that can model two and three dimensional connection structure of switches with an efficient control algorithm using software defined network and verified the functions and analyzed the performance accordingly. The simulator consists of a control module and a switch module that was coded using Python language based on the Mininet and Ryu Openflow frameworks. The control module dynamically controls the operation of switching cells using a shortest multipath algorithm to calculate efficient paths adaptively between configurable computing resources. Performance analysis by using the simulator shows that the three-dimensional switch architecture can accommodate more hosts per port and has about 1.5 times more successful 1:n connections per port with the same number of switches than the two-dimensional architecture. Also simulation results show that connection length in a 3-dimensional way is shorter than that of 2-dimensional way and the unused switch ratio in a 3-dimensional case is lower than that of 2-dimensional cases.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.2
• /
• pp.203-210
• /
• 2015

This paper investigates the failure of a car with a 2.5-liter CRDi engine of the Hyundai Company. The failure is caused by intermittent poor acceleration while driving. To analyze the cause, we investigated the air intake volume, the fuel injection, and the air-fuel ratio, which were determined to be normal. The brake switch signal error was discovered while analyzing the function that limits the output of the engine. While investigating the cause, we discovered the corrosion of the pins on the connector of the brake switch. We determined that it was generated by soapy water flowing in the solar film. Therefore, the cause of the failure was the brake switch signal errors. Additionally, we determined that ECM was the normal fail-safe mode that implemented the override device for safety during normal acceleration. Based on these results, further solar film experiments must be conducted to fully elucidate the causes.

• Journal of Internet Computing and Services
• /
• v.20 no.2
• /
• pp.21-27
• /
• 2019

The terrestrial ATSC 3.0 broadcasting system, which is capable of converging broadcast and communication services, uses IP based technology for data transmission between broadcasting equipment. In addition, data transmission between broadcasting equipment uses IP-based technology like existing wired communication network, which has advantageous in terms of equipment construction and maintenance In case IP based data transmission technology is used, however, it may inevitably cause an error that a packet is lost during transmission depending on the network environments. In order to cope with a broadcasting accident caused by such a transmission error or a malfunction of a broadcasting apparatus, a broadcasting system is generally configured as a duplication, which can transmit a normal packet when various types of error may occur. By this reason, correction method of error packets and intelligent switching technology are essential. Therefore, in this paper, we propose a design and implementation of intelligent IP switch for Ensuring Reliability of ATSC 3.0 Broadcast Streams. The proposed intelligent IP consists of IP Stream Analysis Module, ALP Stream Analysis Module, STL Stream Analysis Module and SMPTE 2022-1 based FEC Encoding/Decoding Module.

• Korean Journal of Optics and Photonics
• /
• v.10 no.1
• /
• pp.73-79
• /
• 1999

Semiconductor optical switch modules of 1$\times$2, 1$\times$4, and 4$\times$4 types for 1550 nm optical communication systems were fabricated by using laser welding technique, embodying in 30-pin butterfly package. For better coupling efficiency between switch chip and optical fiber, tapered fibers of 10~15mm lens radii were used, which provided up to 60% optical coupling efficiency. With the help of new laser hammering process, we could recover the lost optical power almost completely up to average 82% of initially obtained power. The fabricated optical switch modules showed good thermal stability of less than 5% degradation even after 200 times thermal cycling test. The 2.5 Gbps optical transmission characteristics of the 4$\times$4 switch module showed low sensitivities of less than -30dB for all possible switching paths. The transmission penalties of 1$\times$2 switch module at $10^{-10}$ BER were 0.6dB and 0.7dB for 50Xm and 90 Km optical fibers, respectively.

• Proceedings of the KIEE Conference
• /
• 1993.07a
• /
• pp.460-463
• /
• 1993

In this paper, The laser transmitter module is designed as the subsystem of the high repetitive laser rangefinder. The module consists of high voltage power supply, high voltage control circuits, high voltage discharger, electro-optic Q-switch driver, and laser resonator. The high voltage power supply is composed of 2-phase flyback converter. And it has 220W power level and 78% conversion efficiency. From the Q-switch driver of the crossed porro resonator, the phase retardation voltage is switched from 600V to -1500V with 200ns falling time. The module can be operated up to 15Hz. And it generates the laser pulse which has 20ns width and 80mJ.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.4 s.119
• /
• pp.364-371
• /
• 2007

In this paper, the design and implementation of high-power PIN diode switch modules and high-speed switch driver circuits are presented for Wibro base stations. To prevent isolation degradation due to parasitic inductances of conventional packaged PIN diodes and to improve power handling capabilities of the switch modules, bare diode chips are used and carefully placed in a PCB layout, which makes bonding wire inductances to be absorbed in the impedance of a transmission line. The switch module is designed and implemented to have a maximum performance while using a minimum number of the diodes. It shows an insertion loss of ${\sim}0.84\;dB$ and isolation of 80 dB or more at 2.35 GHz. The switch driver circuit is also fabricated and measured to have a switching speed of ${\sim}200\;nsec$. The power handling capability test demonstrates that the module operates normally even under a digitally modulated 70 W RF signal stress.