• Korean Journal of Ecology and Environment
• /
• v.35 no.1 s.97
• /
• pp.28-35
• /
• 2002

The effect of physical parameters on water quality was analyzed using monitoring data of 193 agricultural reservoirs. The retention time of reservoirs ($t_d$) ranged between 10 and 140 days, and the ratio of drainage area (DA) to reservoir surface area (SA) was between 10 and 120. Both ratios of DA/SA and total area (TA)/ reservoir storage (ST) in Korean agricultural reservoirs were relatively greater than those in natural lakes in other countries. As retention time was plotted against DA/SA ratio, it was shorter in Korean reservoirs than natural lakes. The semi-logarithmic relationship between TA/SA and t>$t_d$ was $t_d\;=\;42.21(TA/ST)^{-1}$ (n = 50, $R^2\;=\;0.89$). While areal loading of total phosphorus (TP) was below $4\;gTP{\cdot}m^{-2}{\cdot}yr^{-1}$ in general, it exceeded $10\;gTP{\cdot}m^{-2}{\cdot}yr^{-1}$ in reservoirs where DA/SA ratio was greater than 100, which implies that areal loading of TP increases as DA/SA ratio increases. Chl-a concentration was positively related with the mean depth of reservoir, implying the higher Chl-a concentration with deeper the mean depth. Therefore, the deeper reservoir might be advantageous in water quality management perspective if other morphological conditions are similar. The empirical regression equation using physical parameters was also suggested in the estimation of TP concentration in the reservoirs. Combined information presented in this paper might be applicable to the water quality management in agricultural reservoirs.

• Korean Journal of Heritage: History & Science
• /
• v.53 no.1
• /
• pp.88-105
• /
• 2020

This study examined existing theories of the characteristics of the abandoned tumulus site located at the east side of the Silla era Hwang Bok Sa (皇福寺) site and attempted an archaeological approach based on the derived facts, combining both the results of this study and those of a recently conducted excavation survey. The results of this investigation exhibited the following outcomes. First, the excavation survey revealed that the huge rounded stones discovered on the surface of a rice paddy field located at the east side of the Silla era Hwang Bok Sa were all protecting stones, processed on the front side in the form of a bow, designating a royal tomb. Most of these protecting stones had deviated from their original positions due to subsequent farming practices and some had been re-cycled for construction purposes as fences or foundations for structures built in the Silla era. Considering the prevailing belief in the concept of reincarnation, the bone rank system, and royal authority in the Silla era at that time, it would seem likely that the royal tombs were not intentionally destroyed. Therefore, it is speculated that the stones in this royal tomb were abandoned during construction of the tomb of the King at that time and then naturally re-cycled as building components used in construction sites in later years. Second, this study comparatively analyzed the scale and quality of the supporting stones at the royal tomb site in Guhwang-dong. The analysis results verified that those supporting stones were the same stones from the royal tomb used as supporting stones for statues symbolizing the twelve earthly branch spirits that were restored at the site of the tower at the royal tomb. This confirmed that the statues of the twelve earthly branches spirits sitting at the Hwang Bok Sa site were the protecting stones from a different royal tomb. Accordingly, the conclusion that has been generally accepted to date-that the protecting stones of the statues of twelve earthly branches spirits sitting at Hwang Bok Sa site were probably moved from the royal tomb site in Guhwang-dong-must inevitably be modified. Third, based on the structure of the protecting stones and type of the royal tomb, it is speculated that the individual buried in the royal tomb at Guhwang-dong is one of the kings who followed King Heungdeok and similar times of the buried person of the tomb that was considered as King Gyeongdeok, and who was before the buried person of the tomb that was considered as Kim Yu-sin. In addition, when considering the historical art patterns on the supporting stones of the statues that symbolize the twelve earthly branches spirits, which were moved to the site of the tower at the royal tomb, it is reasonable to believe that the person buried at the royal tomb at Guhwang-dong is likely one of the Kings of the late Silla era of the 9^th century.

• Horticultural Science & Technology
• /
• v.32 no.6
• /
• pp.872-878
• /
• 2014

This study aimed to enhance storage and freshness of strawberry fruits and foliage vegetables by spray treatment with Chlorella vulgaris as a bio-fertilizer. The tested strain, C. vulgaris CHK0008, was isolated from an organically cultivated rice paddy and identified as C. vulgaris by its morphology and 18S rDNA and 23S rDNA sequence homology. We successfully cultured C. vulgaris CHK0008 in BG11 modified medium (BG11MM) and adjusted $2.15{\times}10^6cell/mL$ C. vulgaris CHK0008 to one OD value by measuring the optical density at 680 nm using a UV-vis spectrophotometer. The soluble solid content of 'Seolhyang' and 'Yukbo' strawberry fruits treated by spray application with C. vulgaris CHK0008 was enhanced by 22.2% and 11.5% respectively, compared to untreated controls. Additionally, the decay rates of treated 'Seolhyang' and 'Yukbo' strawberry fruits decreased 63.8% and 74.4% respectively, compared to untreated control. Surface color changes and chlorosis of leaves in leaf vegetables such as lettuce, kale, red ornamental kale, white ornamental kale and beet were observed in samples treated with water spray for 10 days after cold storage. However, the decay rate of leafy vegetables treated with foliar application of 25% C. vulgaris CHK0008 liquid culture was significantly decreased compared to that of the untreated control during storage at $4^{\circ}C$.

• Journal of dental hygiene science
• /
• v.13 no.3
• /
• pp.223-229
• /
• 2013

The aim of this study was to examine the effectiveness of oral health promotion program in a group of 9~18-year-old children and adolescents living in four orphanages in Dong-gu, Daejeon. The program was based on oral disease prevention program including oral health education, fluoride application and scaling every six months. Oral health status of total 109 orphans was examined by one dentists who were trained in 2010 Korean National Oral Health Survey. Dental caries index, community periodontal index and modified patient hygiene performance index (M-PHP) were checked using dental unit chair. Child oral health impact profile (COHIP) and subjective oral health recognition survey were carried out. Compared with data of 2010 national sample, the mean of decayed, missing and filled teeth showed no difference between the subjects and test values, but the means of decayed teeth, decayed surface, toothbrushing frequency of the subjects showed to become worse with advancing years in spite of oral health promotion program. COHIP, subjective oral health status showed lower than test values, too. In M-PHP and Calculus index, the subjects showed better by periodic oral health education and scaling. We suggest that oral health promotion program for orphans include oral disease treatment program as well as preventive program to improve oral health of orphans efficiently. And, oral health promotion program has to be connected with psychological support for improving quality of life of orphans.

• Radiation Oncology Journal
• /
• v.14 no.3
• /
• pp.237-244
• /
• 1996

Purpose : The accurate dosimetry of independent collimator equipped for 6MV and 15MV X-ray beam was investigated to search for the optimal correction factor. Materials and Methods : The field size factors, beam quality and dose distribution were measured by using 6MV, 15MV X-ray Field size factors were measured from $3{\times}3cm^2$ to $35{\times}35cm^2$ by using 0.6cc ion chamber (NE 2571) at Dmax. Beam qualities were measured at different field sizes, off-axis distances and depths. Isodose distributions at different off-axis distance using $10\times10cm^2$ field were also investigated and compared with symmetric field. Result: 1) Relative field size factors was different along lateral distance with maximum changes in $3.1\%$ for 6MV and $5\%$ for 15MV. But the field size factors of asymmetric fields were identical to the modified central-axis values in symmetric field, which corrected by off-axis ratio at Dmax. 2) The HVL and PDD was decreased by increasing off-axis distance. PDD was also decreased by increasing depth For field size more than $5{\times}cm^2$ and depth less than 15cm, PDD of asymmetric field differs from that of symmetric one ($0.5\~2\%$ for 6MV and $0.4\~1.4\%$ for 15MV). 3) The measured isodose curves demonstrate divergence effects and reduced doses adjacent to the edge close to the flattening filter center was also observed. Conclusion . When asymmetric collimator is used, calculation of MU must be corrected with off-axis and PDD with a caution of underdose in central axis.

• Clean Technology
• /
• v.24 no.1
• /
• pp.55-62
• /
• 2018

The adsorbent used in water-adsorption cooling system utilizing low-temperature heat of below $90^{\circ}C$ is required to exhibit high water uptake capacity at a relative humidity ($P/P_0$) between 0.1 and 0.3. Mesoporous silica (MCM-41) and MOF(MIL-101) exhibit quite large water adsorption capacity under saturated water vapor at $35^{\circ}C$. However, these adsorbents show small water adsorption capacity ($0.027{g_{water}\;g_{ads}}^{-1}$, $0.074{g_{water}\;g_{ads}}^{-1}$, respectively) in the relative humidity ($P/P_0$) range of 0.1 to 0.3. In this study, the surface properties of mesoporous silica and MOF were modified by simple methods to develop an adsorbent having a higher water uptake than the conventional water adsorbents at a relative humidity ($P/P_0$) of 0.1 ~ 0.3. In the case of mesoporous silica (MCM-41) exhibiting mainly water adsorption at $P/P_0=0.5{\sim}0.7$, aluminum species was functionalized on the mesopore walls and then cations existing near the aluminum were exchanged with various cations (e.g., $Na^+$, ${NH_4}^+$, and $(C_2H_5)_4N^+$). In addition, 20 wt% (to total weight of the composites) of hygroscopic inorganic salt ($CaCl_2$) was impregnated on the MCM-41. In the case of the MIL-101 (MOF), 20 wt% of hygroscopic inorganic salt ($CaCl_2$) was impregnated on the MIL-101. The MCM-41 which was ion-exchanged with various cations has main adsorption branch around 0.5 of $P/P_0$ which was slightly shifted with low-pressure direction in comparison with pristine MCM-41. However, tiny increases were observed on the adsorption in the range of $P/P_0$ between 0.1 and 0.3. After salt impregnation on the MCM-41, the adsorption capacity under $P/P_0=0.1{\sim}0.3$ at $35^{\circ}C$ was increased from $0.027{g_{water}\;g_{ads}}^{-1}$ to $0.152{g_{water}\;g_{ads}}^{-1}$. In the case of MIL-101, the amount of water adsorption at $35^{\circ}C$ under $P/P_0=0.1{\sim}0.3$ was increased from $0.074{g_{water}\;g_{ads}}^{-1}$ to $0.330{g_{water}\;g_{ads}}^{-1}$ after the salt impregnation.

• Journal of the Korean Electrochemical Society
• /
• v.9 no.3
• /
• pp.124-131
• /
• 2006

For commercialization of molten carbonate fuel cell (MCFC), it has some problems to be overcome such as decrease of porosity and thickness of the anode under the operating condition (at $650^{\circ}C$ and working pressure of more than 2 $kg_f/cm^2$). Recently, Ni-Al alloy anode has been proposed to replace the conventional Ni-Cr anode as an alternative material to resist a creep and inhibit the sintering. The objective of this research is to sinter the green sheet of Ni-Al alloy anode during single cell pre-treatment process, which has several advantages like cost down and simplification of manufacturing process. However, the Ni-Al alloy anode prepared with a conventional pre-treatment process showed the phase separation of Ni-Al alloy and formation of micropore(${\leqq}0.4{\mu}m$), resulting in low creep resistance and high electrolyte re-distribution. In order to prevent the Ni-Al alloy anode from phase-separating, nitrogen gas was used in the process of pre-treatment. Introducing the nitrogen, the phase separation from Ni-Al alloy into nickel and alumina was minimized and increased creep resistance. However, there was some micropore formation on the surface of Ni-Al alloy anode during the cell operation due to creation of lithium aluminate. Addition of more amount of electrolyte into a cell, especially at cathode, made the cell performance stable for 2,000 hrs. Consequently, it was possible to make the Ni-Al alloy anode with good creep resistance by the modified in-situ sintering technique.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.45 no.11
• /
• pp.1673-1680
• /
• 2016

The purpose of this study was to examine how customer orientation (CO) reduces employee stress to customers (CSS). As emotional labor strategies [surface acting (SA) and deep acting (DA)] may mediate a role between CO and CSS, we verified multiple parallel mediator roles of SA and DA between CO and CSS. Our survey was administered to 323 school foodservice employees in Daegu and Gyeongbuk. The results show that CO increased DA but did not decrease SA, and SA had a positive effect on CSS while DA did not influence CSS. These results did not support the parallel multiple mediator model. We conducted post-hoc model modification and proposed the serial multiple mediator model as a modified model. As a result, CO increased DA, DA reduced SA, and SA showed a positive relation with CSS. This double mediating effect through DA and SA between CO and CSS was significant. Based on these results, we found that CO did not have a direct effect on SA and CSS. DA did not directly reduce CSS while CO reduced SA and CSS through DA indirectly. DA had a negative effect on CSS through SA indirectly. Finally, implications and limitations of this are discussed.

• Korean Journal of Food Science and Technology
• /
• v.34 no.6
• /
• pp.1048-1056
• /
• 2002

Quality of fresh ginger deteriorates rapidly during low temperature storage, and its storage life is short due to sprouting and microbial spoilage. The objectives of this research were to develop, using additives, a minced ginger product, which could maintain acceptable quality for over 30 days, and to investigate its quality changes during the cold storage. Storage stability of minced ginger product was investigated from the standpoint of the inhibition of brown discoloration, gas formation and liquid-solid separation. Fresh ginger was peeled and ground to produce minced ginger (control). Sodium bisulfite, L-cysteine, NaCl, sodium benzoate, modified starch, and/or xanthan gum were added to the control to minimize quality loss during storage, and to develop an optimum formula (A) of minced ginger. Samples were packed in Nylon/PE films, stored at $5^{\circ}C$, sampled at a 30-day interval, and subjected to quality evaluations. Changes in pH, surface color, gas formation, liquid-solid separation, contents of free amino acids, free sugars, organic acids, and fatty acids were determined. Gas formation was effectively inhibited in samples with sodium benzoate and/or NaCl. Samples with xanthan gum did not result in liquid-solid separation. L-Cysteine and sodium bisulfite were effective in controlling discoloration. pH decreased during storage in all samples, except sample A. Organic acid contents of all samples increased during storage, with lactic acid content showing the highest increase. Free amino acid content decreased with increasing storage time. Free sugar content of all samples decreased during storage. Sensory results showed sample A maintained acceptable quality until 90 days of storage. These results suggest that quality of minced ginger could be successfully maintained with the additions of selected additives for up to 90 days.

• Applied Chemistry for Engineering
• /
• v.33 no.2
• /
• pp.173-178
• /
• 2022

A lateral flow immunoassay (LFIA) method using carbon nanodot@silica as a signaling material was developed for analyzing the concentration of retinol-binding protein 4 (RBP4), one of the lung cancer biomarkers. Instead of antibodies mainly used as bioreceptors in nitrocellulose membranes in LFIA for protein detection, aptamers that are more economical, easy to store for a long time, and have strong affinities toward specific target proteins were used. A 5' terminal of biotin-modified aptamer specific to RBP4 was first reacted with neutravidin followed by spraying the mixture on the membrane in order to immobilize the aptamer in a porous membrane by the strong binding affinity between biotin and neutravidin. Carbon nanodot@silica nanoparticles with blue fluorescent signal covalently conjugated to the RBP4 antibody, and RBP4 were injected in a lateral flow manner on to the surface bound aptamer to form a sandwich complex. Surfactant concentrations, ionic strength, and additional blocking reagents were added to the running buffer solution to optimize the fluorescent signal off from the sandwich complex which was correlated to the concentration of RBP4. A 10 mM Tris (pH 7.4) running buffer containing 150 mM NaCl and 0.05% Tween-20 with 0.6 M ethanolamine as a blocking agent showed the optimum assay condition for carbon nanodot@silica-based LFIA. The results indicate that an aptamer, more economical and easier to store for a long time can be used as an alternative immobilizing probe for antibody in a LFIA device which can be used as a point-of-care diagnosis kit for lung cancer diseases.